Sensors
detect a physical event then translate to a representative analog signal.
See Also: Measurement, Detectors, Meters, Transducers
-
product
Spot Sensor
SP 1000-20R1
Advanced Thermal Solutions, Inc.
The SP 1000-20R1 is a single-sensor probe designed for measuring the surface temperature of solids. Its small size allows for the exact positioning of the sensor at the desired spot. The size of the sensor eliminates any conductive heat transfer that may occur through the lead wire, enhancing measurement accuracy.
-
product
Reference Cells For PIV-IV Systems
NREL calibrated cell used for calibration transfer.The Abet Technologies solar reference cell is a precision instrument for the determination of solar simulator irradiance levels. The sensor is a mono-crystalline silicon solar cell having an area of2x2cm(4cm).The back of the solar cell is attached to the device in such a way that a good heat transfer to the device housing is guaranteed. Below the solar cell a Pt100 RTD temperature sensor is mounted to allow monitoring of device temperature. The device is not shunted allowing the whole IV-curve to be measured. The solar cell is protected by a high quality fused silica window, assuring spectral sensitivity over a 320 -1100 nm range.
-
product
PXI High Density Precision Resistor Module, 9-Channel, 3Ω to 52.4kΩ
40-298-033
The 40-298-033 is a high density programmable resistor module with 9 channels which can be set between 3Ω and 52.4kΩ with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Thermal Camera Cores
Tenum® 640
With a 10 μm pixel pitch and <30 mK NETD sensitivity, the Tenum 640 represents the latest evolution in low SWaP long-wave infrared technology. Tenum® 640 precisely balances ultra-small pixel structure with ultra-sensitive microbolometer performance at a remarkable cost advantage. The 10-micron pixel pitch Vanadium Oxide (VOx) technology behind Leonardo DRS’ Tenum® 640 is the most advanced uncooled infrared sensor design available to Original Equipment Manufacturers (OEMs) today.
-
product
Local Discomfort Temperature Probe
TP3227K
Temperature probe composed of 2 independent probes, Pt100 sensor used for measuring local discomfort due to vertical thermal gradient.
-
product
Intelligent Refractive Index Sensor – Inline Process Refractometer
IRIS+
The MISCO IRIS+™ Intelligent Refractive Index Sensor is an enhanced version of the popular IRIS Sensor. The main differences are that the IRIS+ has an integrated stainless flow-through adapter, slightly expanded operational temperature and pressure limits, and slightly better precision.
-
product
High Precision Compression Type Load Cell
IR
A high-precision compression-type load cell is a sensor that accurately measures compressive (pushing) forces, designed for applications requiring very tight accuracy and reliability. It works by converting a downward force into an electrical signal, often using strain gauges to measure deformation, and is used in demanding fields like calibration, manufacturing, and medical equipment.
-
product
5MP MIPI Camera Module
E-CAM55_CUMI0521_MOD
e-CAM55_CUMI0521_MOD is a small form factor, 5 MP fixed focus camera module based on AR0521 CMOS image sensor from ON Semiconductor® has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs all the Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images and video. This low light camera module can stream uncompressed VGA (640 x 480) at 75 fps, HD (1280 x 720) at 100 fps, 1280 x 960 at 75 fps, FHD (1920 x 1080) at 65 fps, 2560 x 1440 at 38fps, 2592 x 1944 at 28 fps.
-
product
Carbon Monoxide Detector Tester
Solo C3
Many multi-sensor fire detectors detect carbon monoxide (CO) as well as smoke and / or heat. Under international codes and standards the CO cell needs to be functionally tested with a CO stimulus from the protected area through the detector vents to the sensor.
-
product
Bio-Threat Detection & Collection
IBAC 2
The IBAC 2 is a fully automated bio-detection sensor that can support continual, 24/7, air monitoring or can be set to targeting sampling windows to align to hours of operation. It alarms in less than 60 seconds when a bio-threat is present. IBAC can be configured to support automated aerosol sampling either in conjunction with its’ triggered alarms or at a set frequency sampling time. In wide service throughout the world, IBAC 2 is used to collect and detect aerosolized agents for all four classes of biological threats (spore, viral, cellular, and protein toxins) with low false alarm.
-
product
TEV Antenna
TEV sensor is a partial discharge sensor whose working principle is based on a direct Capacitive coupling with a Switchgears earthed metal case. The two ends of TEV sensor can be coupled magnetically to virtually any opening on a metal Surface. It picks up the electric signal given by PD activity onto the two metallic surfaces. Thanks to its special design has high sensitivity, larger than other single ended TEV sensors. His compact and robust design (passive sensor) makes the TEV the optimal sensor for direct installation on medium voltage Switchgears.
-
product
Stud Finders
Zircon offers a wide range of stud sensors with different combinations of features, allowing you to choose the tool that fits your unique needs. While Edge Finders locate stud edges, Center Finders simplify your project by pinpointing the stud center for you.
-
product
Exhaust Back Pressure Tester
33600
Use to test for clogged or obstructed catalytic converters and mufflers. Fast and easy to use - threads into Oxygen Sensor Port. Includes 12mm and 18mm adapters to fit most domestic and imported vehicles. Gage measures 2 1/2" diameter and has dual scale: 15 PSI and 1.00 Kg/Cm2. Hose is 41" long.
-
product
Piezoelectric Vibration Pickup
PU-6GHT6
*High-sensitivity type for sensoring*low-rotation from 0.2Hz
-
product
Capacitive Electromagnetic Flow Sensor
WFC
This is a flow sensor with a through structure.No foreign matter is clogged or detection failure occurs. Ideal for spot welding machines, various machine tools, induction hardening equipment, etc.
-
product
Environmental Test Chamber
The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip.The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1 and humidity is 0.1%R.HThe temperature sensor is platinum PT100 Ohms/MV resistor
-
product
Sonin Water Alarm with Flat Sensor
00701
Protect your home or business from costly water damage by placing a Sonin Water Alarm with Flat Sensor anywhere there is a potential for a leak.
-
product
Low Input Bias Current Amplifiers (<100 pA)
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
product
Current Probe
DCP-BTA
Vernier Software & Technology, LLC
The Current Probe measures DC and low-frequency AC currents up to 600 mA. Use Current Probes in combination with Differential Voltage Probes to investigate Ohm's Law and explore series and parallel circuits. The 0.1 shunt resistor minimizes changes to your circuit. If currents will exceed 1 A, use the High Current Sensor.
-
product
8-Channel VME Tachometer
V360
The V360 is a single-width, 6U height VME module designed specifically to acquire low frequency inputs from industrial speed sensors. The module can measure frequency and period over a wide dynamic range, and is specifically designed to ensure reliable measurement in high-noise industrial environments.
-
product
2MP Sony STARVIS® IMX290 Ultra-Lowlight Camera Module
e-CAM21_CUMI290_MOD
The e-CAM21_CUMI290_MOD is a 2 MP ultra-lowlight RAW MIPI camera module with the S-mount (M12) lens holder. This FHD camera module is based on SONY IMX290, one of the most popular Sony's STARVIS® CMOS sensor. SONY IMX290 is a 1/2.8" rolling shutter CMOS sensor with 2.9µm pixel size. Its effective pixel back-illuminated technology with improved sensitivity in the visible-light and near infrared light enables customers to capture images even in absolute darkness. The e-CAM21_CUMI290_MOD can stream uncompressed FHD @120 fps in 10-bit mode and 60fps in 12-bit mode.
-
product
Water Alarm with Remote Sensor
00800
Protect your home or business from costly water damage by placing a Sonin Water Alarm with Remote Sensor anywhere there is a potential for a leak.
-
product
Turbidity Sensor
AF56-N
AF56-N is a high precision sensor for direct installation into pipelines measuring NIR light absorption (turbidity) of various liquid samples. The optical path length can be individually configured to meet the process control requirements.
-
product
Q Travel mini
The Q.Travel-mini is based to the Q.raxx modules from Gantner Instruments. With one Controller (Q.gate) and three slots for sensor modules (Q.bloxx) a flexible system for all types of measurements is possible. All modules can be used in combination with each other. The different sensor modules are shown in the overview.
-
product
Angle Position On-Axis
The magnetic rotary position sensor product family detects the absolute angular orientation of an on-axis two-pole magnet rotating over the center of the IC. The absolute angular position can be provided in various formats, including PWM, ABI and UVW, or directly read through the host interface. According to the application’s requirements, resolutions from 8-bit up to 14-bit are available. This technology can be employed in high-accuracy angle position detection, high-speed rotation systems and brushless DC motor control. Any rotary magnetic position sensor can replace either absolute or incremental optical sensors, other magnetic and inductive technologies, potentiometers or magnetic switches.
-
product
Pressure Based Waves
5218
Measure pressure based Waves with the Aanderaa Wave Sensors- compact fully integrated sensors for measuring wave and tide conditionsThe 5218 wave sensor is designed to be mounted on the Aanderaa SeaGuard top-end plate or connected to SmartGuard using AiCaP CANbus or in other measurement systems using the RS-232 interface.The 5218R wave sensor sensor is designed for use with long cables by means of RS-422 full duplex interface.Both wave sensors are based on a silicon piezoresistive pressure sensor. The pressure measurements are sampled and temperature compensated by an advanced Digital Signal Processor.The wave sensor application areas are in fixed installations, either deployed in a seabed installation in shallow waters, or mounted onto a fixed structure in the upper water column.
-
product
NON CONTACT INFRARED THERMOMETER
IBL-MTX9
International Biological Laboratories
This Digital Non Contact type Infra Red cum Contact type Thermometer with laser sensor uses temperature sensor of Thermopile 7 - 14 mm to measure temperature from -18 to 1000 Degree C in the Non Contact Infra Red Mode and -20 to 1300 Degree C in the contact mode using K type Thermometer and also in Fahrenheit scale.
-
product
Distance Sensor Technology
Inductive sensors
Inductive sensors measure the position changes of metal objects without contacting them. The ever increasingly optimized repeatability paired with the outstanding precision in measuring paths, angles, and positions when applied increase the productivity of every machine.
-
product
MicroLogPRO III USB Data Loggers
The MicroLog product line includes a range of low-cost, portable data loggers for supply chain monitoring, featuring internal temperature and humidity sensors with one external input for connection to temperature, current and voltage sensors. With over a decade of customer satisfaction, the MicroLog continues to offer application reliability for a variety of mission critical industries such as cold chain, healthcare, pharmaceuticals, and storage.
-
product
PXI Precision Resistor Module 4-Channel, 1.5 to 1.81k
40-297-122
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
