Product

High Voltage Surge Current Monitors

HVSCM

-

Test Electronics

HVSCM - Test Electronics

Designed to be used with the Model HVST High Voltage Surge tester. The Surge Current Monitor allows simultaneously surge testing 20 units. The Surge Current Monitor monitors the current going through each unit under test at the time of the surge. If a unit under test breaks down or leaks, the Surge Current Monitor will identify the bad unit by lighting the corresponding LED. The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. In production testing we expect that most of the time the devices will pass. In the event that one should fail, the failed device would be removed and then all the parts would have ot undergo another surge test. Since most devices pass most of the time, simultaneous surge testing can be a real time saver.

Product

Raptor HV High Voltage Tester

-

EUROSMC, S.A.

EUROSMC, S.A.

The Raptor-HV, also called the high voltage slave, is an optional product that extends the Raptor’s applications to tests that require the use of a moderately high AC voltage.

Product

High Voltage

-

Mess- & Prüfsysteme GmbH

Mess- & Prüfsysteme GmbH

Accurate measurement of high voltages acc. to VDE 0432 und IEC 60060 in conjunction with a high voltage divider.For the measurement, the principle of capacitive or resistive divider is used, which can be selected in the peak voltage meter.

Product

High Voltage Power Sources

-

Electronic Test & Power Systems

Electronic Test & Power Systems

A comprehensive range of high voltage power sources are available from ETPS. Product families range from programmable high precision laboratory power supplies to HV Cassettes and PCB modules.

Product

High Voltage Probe: Single-Ended

-

Tektronix, Inc.

Tektronix, Inc.

A high voltage single-ended probe is typically used for measuring ground referenced signals up to 40 kV. However, some single-ended probes are designed for oscilloscopes with isolated or floating inputs for measurements that are not ground referenced. Users should select probes with a low input capacitance specification (< 4 pF) to minimize the probe’s loading effect on the circuit because a probe with lower input capacitance will offer higher input impedance at higher frequencies.

Product

High Voltage SMU 2500 V

AXV7607

-

VX Instruments GmbH

AXV7607 - VX Instruments GmbH

Generate extremely short, fully regulated voltage pulses of up to 2500 V. Measure leakage currents up to the pA range.

Product

High Voltage Breakdown Test Sets

HT-Series

-

Becker & Hickl GmbH

HT-Series - Becker & Hickl GmbH

Dielectric Voltage Withstand Test or High Potential Test (HIPOT test) is a 100% production line test to verify the quality & electrical safety characteristics of products.

Product

AC HIGH VOLTAGE TEST SET

-

International Biological Laboratories

International Biological Laboratories

IBL" make High voltage testing sets are suitable for Power frequency AC high voltage test on transformers, motors, insulators, cables etc. The sets are capable of giving continuously variable AC HIGH VOLTAGE from zero to maximum rated output voltage.

Product

High Voltage Programmable DC Power Supplies

-

TDK-Lambda Corp.

TDK-Lambda Corp.

High Voltage Programmable DC Power Supplies

Product

High Voltage Switching Systems

HXV Series

-

Cytec Corp.

HXV Series - Cytec Corp.

HXV products are high voltage systems intened for Hi-pot / IR or High voltage switching. They can be configured to drive from 32 to 128 switch points per chassis and can be configured as multiplexer (1xN) or Matrix (NxM) configurations. Stand HXV chassis are used for signals up to 5000 VAC rms ( 7400 V peak ) and can carry up to 5 amps of current. Custom systems can be built up to 25KV. Most of the modules used in these systems are 1xN multiplexers or 2x4 matrix modules that can be combined to form larger multiplexers or matrices. Connector options for standard HXV include 5 way banaba jacks / binding posts, Shrouded Banana Jacks or SHV ( High voltage BNC) if you need to use a high voltage cable with a grounded shield for safety applications. Control options include 10/100BaseT Ethernet LAN, RS232, GPIB or optional manual control. Standard HXV systems use high voltage reed relays. Custom HXV systems up to 25KV use application specific relays and connectors from a variety of vendors based on required specifications.