Tesla Meters
measures magnetic fields. 1 Telsa equals 1000 gauss.
See Also: Teslameters, Gaussmeters
-
Product
pH Pocket Water Meter
LAQUAtwin pH-11
-
The only pocket meter that directly measures pH in 0.1ml sample (or 0.05ml sample with sampling sheet B). Unique sensor allows measurement of viscous liquids, solids, and even powder samples. No need for a beaker to calibrate your meter or measure a sample. Just place few drops of the standard or sample onto the flat sensor. This procedure saves you time and prevents wasting your precious sample.
-
Product
Handheld Clamp Meter, 3 ½ Digit
U1212A
Digital Multimeter
Handle large currents up to 1000 A safely with 2-inch large jaw opening. Keysight Remote Link Solution allows datalogging wirelessly via Bluetooth.
-
Product
Benchtop Meter
pH 700
-
Economical, user-friendly and accurate, the Eutech pH 700 is your ideal choice for routine applications in laboratories, productions plants and schools.
-
Product
LCR Meters
4300 Series
-
Accurate and fast measurements may be made from 20Hz to 1MHz (43100) making the 4300 series the ideal choice for many applications in the test or production environments.
-
-
Product
Digital Lamp Cap Torque Meter
CX-L338
-
Shenzhen Chuangxin Instruments Co., Ltd.
Lamp Cap Torsion Meter is a newly developed intelligent product with microprocessor built-in.
-
Product
Digital Panel Meter
CM3-VA9
-
CM3-VA9 is a multifunctional 3-phase voltage/ current meter.With 3 phase voltage or current display at the same, configurable display range via front buttons, anti-inference design, reliable quality and easy to use and install, CM3-VA9 also has multiple I/O functions including 6relay outputs, 3 analogue output and a RS485 communication port running the Modbus RTU Protocol
-
Product
Resistivity Meter with Multi Electrode
POLARES
-
Till this moment the use of Electrical Resistivity Tomography (ERT) for geology has always been basically the same since its debut, based on the original vertical Electrical Soundings (VES) principles: applying a continuous current to two stakes inserted into the ground and measuring the corresponding voltage between other two. The applied current and thus the relative tension have always been continuous, with an inversion in polarity for each measure. The new tool POLARES uses an alternate current, instead, sinusoidal type, with an adjustable frequency.
-
Product
Portable Power Factor Meter
ST-2000 Cos∮
-
Standard Electric Works Co., Ltd
● Principle : Phase angle sensing transducer● Rated Accuracy : ±3% phase angle● Scale : Power Factor：Lead 0 – 0.3 – 1.0 – 0.3 – 0 Lag Power Angle： Lead 90° – 0° – 90° Lag● Effective Power Factor Measuring Range : Lead 0.5 – 1.0 – 0.5 Lag● Scale Length : Approx. 135mm(5-3/8”)● Frequency Influence : Within ±1.5° phase angle at 45 to 65Hz
-
Product
20J3 SHEET RESISTANCE METER
-
Non-contact measurement of Ohms/sq, Ohms-cm, resistivity, thickness, and moreMeasures nearly all thin conductive materials or coatingsChoose a sensor in one of four ranges, from .005 Ohms/sq to 100,000 Ohms/sqadd other sensors laterFor benchtop or inline applicationsSimple one-button operationSmall footprint with detached sensor probeOptions include vacuum-ready probe, PC-based productivity software, Ethernet connectivity, stage, and more
-
Product
Dew Point Meters
-
Measures and records climatic conditions including: Relative humidity, air temperature, surface temperature, dew point temperature, wind speed and difference between surface and dew point temperatures. Ideal for surface preparation as required by ISO 8502-4, BS 7079-B4, ASTM D3276, IMO PSPC, SSPC-PA7 and US Navy NSI 009-32. View Video
-
Product
Benchtop Water Quality Meters
LAQUA PH1200
-
Water quality analysis is repeatedly performed in laboratories on a daily basis. Our high-end benchtop model was developed to provide simplicity with excellent on-site usability - from operation and maintenance through to troubleshooting.
-
Product
Reference Meter
ST1000
-
Shenzhen Star Instrument Co., Ltd.
The ST1000 three-phase reference meter incorporates high-precision A/D converter, DSP, wide-range measuring and embedding industrial PC technologies. It has a high accuracy of class 0.01. The voltage measuring range (phase voltage): 1V~480V, current measuring range: 1mA~120A.
-
Product
Laser Power Meters
-
Laser Power meters are a vital tool in your Preventative Maintenance regime.They allow you to quickly test the the performance of your optical system (laser source / mirrors / lens) and pin point any potential issues before they can affect your product quality and production throughput.Power meters are great for determining if specific components are starting to deteriorate, allowing you to order and replace without impacting too seriously on your production.The power meter measures the laser output for the following laser sources and wavelengths:CO2 Glass DC Laser Tube / 8~11 microns or 8,000 ~ 11,000 nm wavelengthCO2 RF Metal or Ceramic Laser / 8~11 microns or 8,000 ~ 11,000 nm wavelengthYAG Laser / 900 ~ 1250nm wavelengthFiber Laser / 900 ~ 1250nm wavelength
-
Product
Benchtop pH/Conductivity Meter
LAQUA PC1500
-
Ideal for routine applications and student training.Good value for money: no fancy bells and whistles which sounds good but are rarely used.
-
Product
Current Meter
MTD32
-
The mezzanine module (mezzanine) MTD32 is designed to measure instantaneous current values over 32 channels.
-
Product
Rotating Torque Meter
NTS-6 series (S1/S2/S5/S10/S20)
-
Torque measurement of rotating body. Measure rotational torque during assembly of devices with rotating functions and on finished products. While the output shaft self-rotates, the built-in sensor catches load fluctuations on the rotating body. It is possible to measure the rotation starting torque of the rotating object ( which does not rotate by itself and does not have power) and the load torque during rotation. (Printers, copiers, zoom lenses, door knob mechanisms, hinge mechanisms, etc...)
-
Product
Multi-Featured Clamp Meters
-
Amprobe’s multi-featured clamp meters cover a broad range of industrial, HVAC and electrical applications.
-
Product
Light Flicker Meter
LiFli
-
The LiFli light flicker meter enables fast evaluation of light sources on the flickering part (flicker / flicker). Especially in the case of LED lamps, the flicker portion can be determined only by one measurement, since it is in the range of 0% to 100% for these luminous means.Audio features enable the flicker to be reproduced acoustically. A voltage output for further analysis by means of oscilloscope or voltage analyzer is available.
-
Product
Live-Dead-Live Meter Verifier
LDL-1200
-
The Live Dead Live (LDL) Meter Verifier is a small, lightweight, robust, portable, handheld power supply. It supplies just under 150 volts, AC (rms) or DC with a maximum current of less than 5 mA at rated voltage. The LDL-1200 Meter Verifier is specifically designed to facilitate voltage verification tests on most digital multi-meters, electronic voltage detectors, voltage testers, neon test lights, tic tracers and other commonly used electrical voltage test apparatus, while keeping the user as electrically safe as possible with its extremely low “volt-amp” output.
-
Product
T Series Panel Meter
ST-125
-
Standard Electric Works Co., Ltd
● Hz Meter : Measuring Ranges : 45~56 Hz, 45~55 Hz, 55~65 Hz Rated Voltage : 110V, 220V Accuracy : ± 2.0% full scale● Case and Composition: ABS case and PC cover Four studs mounting● Accuracy : ± 2.0% full scale value● Color：Black case and white scale plate.● Pointer：Knife-type, color in black.
-
Product
Electricity Meter Test Equipment
ELMA
-
The Electricity Meter Test Equipment ELMA due to modular concept enables to tailor specifications to specific laboratory demand. The available power and the maximum current of 240 A of extremely pure synthesized 4-quadrant test signal covers the needs of both precision and high capacity testing laboratories.
-
Product
Transformer Turns Ratio Meters
-
Vanguard Instruments Company, Inc.
The ATRT-01 S3 is Vanguard’s fourth generation, micro-processor based, single phase, automatic transformer turns-ratio tester. The ATRT-01 S3 uses the IEEE C57.12.90 measuring method to determine the transformer turns-ratio. The transformer turns-ratio is determined by precisely measuring the voltages across the unloaded transformer windings. The ATRT-01 S3’s measuring circuitry self adjusts before each measurement to ensure turns-ratio accuracy. Two selectable test voltages, 4Vac and 40Vac, offer flexibility in testing different types of transformers.
-
Product
Digital Panel Meter
MPF-5A
-
Mx-5A meter to provide power (Watt or Active Power or Re-active Power or Power Factor), high-precision measurement, display and remote communication capabilities.Additional purchase: 1 group of relay outputs, 1 analog output, an RS485 communication output (the Modbus RTU Mode) interface, so that can be installed in power management, remote input and output, alarm and variety of remote communication control the use of needs.120mm (D) is ideal for assembling in panels with limited penetration depth
-
Product
AC/DC TRMS Insulation Clamp Meter
CMi210
-
A unique insulation clamp meter for the installation, testing and maintenance of domestic and industrial installations. This high specification clamp meter can perform insulation tests to 6G Ohms with 5 test voltages from 50V to 1000V.
The clamp provides True RMS measurement of AC current to 1500A and AC voltage to 750V. It will also measure DC current to 2000A and DC voltage to 1000V. The CMi210 has all the same test functions you would expect to find on a high specification multimeter with the added benefit of temperature measurement.
-
Product
C/I Clamp Meters
-
AC current measuring capability up to 400 amps. Compact size, fits easily into tool pouch. Data hold and Max hold to capture important readings. Lifetime Limited Warranty.
-
-
Product
Paper Moisture Meters
-
A paper moisture meter measures the humidity of paper and paper products. Use of a paper moisture meter can prevent costly damages resulting from paper expansion or shrinking. A paper moisture meter determines paper moisture content based on either absolute humidity or relative humidity. Absolute humidity does not take into consideration temperature, while relative humidity relies on temperature and is expressed as a percentage of the total amount of moisture possible at the current temperature. Thus, many paper moisture meter devices feature automatic temperature compensation (ATC).For paper producers, paper manufacturers, paper mills and others in the pulp and paper industry, moisture and humidity control is essential, especially during the production process, as excessive moisture can lead to warming of the paper rolls. A paper moisture meter can be used to detect moisture streaks during the paper production process as well as to identify optimal drying times.Regardless of whether paper is stored in paper rolls in paper converting plants or stacked in sheets and paper bales in commercial printing warehouses, the porous surface of paper gradually takes in moisture relative to the humidity of the surrounding environment. This moisture can be problematic, as too much moisture can cause curling, buckling or the formation of waves in otherwise flat paper products. Moisture also can prevent inks, dyes, paints and coatings from covering and saturating paper properly during printing and processing.PCE Instruments (PCE) offers digital handheld moisture meter devices for measuring the moisture content of paper and paper products such as cardboard, paperboard, corrugated boxes, craft paper, wrapping paper, brown packaging paper, butcher paper, recycled paper, coated paper and more. Different paper moisture meter models utilize different paper moisture measuring techniques, performing moisture content tests of paper products via either destructive or nondestructive methods. Typically, a standard pinless paper moisture meter is nonpenetrating, thus allowing for the nondestructive measurement of paper water content.
-
Product
Plug in Meters
-
make accurately measuring the power (watts) and energy (kilowatt-hours) consumption of 117vac plug in appliances a snap!
-
Product
Transformer Winding Resistance Meters
TWA Standard Series
-
The TWA standard series instruments are designed to measure the resistance of six coils and simultaneously analyze the three-phase tap changer on load of the primary and secondary transformer coils (provided by model TWA40). This is done in a single cable configuration, with test currents up to 40A. Each transformer configuration has a special measurement algorithm that is optimized for rapid stabilization of test results. The TWA instruments generate a true DC current without ripple. Both current injection and magnetic circuit energy discharge are automatically regulated.
