Isolated Digital Input Modules
-
Product
PCI Very High Density Multiplexer, 10-Channel, 16-Pole
50-670C-022-10/16
Multiplexer Module
The 50-670C-022-10/16 is a 10-channel, 16-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5280 Series
Digital I/O
The GX5280 Series are high performance, cost-effective 3U PXI dynamic digital I/O boards with 32 TTL input or output channels and 32 LVDS input or output channels. The GX5280 Series offers an industry leading 512 MB of on-board memory and supports test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
Breadboard Module for 34980A
34959A
Breadboard Module
The Keysight 34959A module for the 34980A Multifunction Switch/Measure Unit can be used to create custom designs inside the Mainframe. You can control your circuits with access to both the +12V and +5V supplies, 16 GPIO ports, and 32 relay drive lines. The faceplate has cutouts for the most common connectors. The breadboard module can be programmed using standard read and write commands in SCPI.
-
Product
PXI High Density MUX BRIC, 20-Chan, 40-Pole
40-570-215
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
PXI Monitored Multiplexer, Single 64-Channel, 1-Pole
40-619-301
Multiplexer Module
The 40-619-301 is a high density PXI 2 A multiplexer module in single 64-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
Product
PXI Hex SPDT RF Switch 3GHz 50 SMB
40-870-006
Switch Module
The 40-870 is a 50 RF Switch available with 3 or 6 separate SPDT relays in a single PXI slot. Both versions exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40-870 has been minimized by careful attention to the mechanical and electrical design.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode
40-852A-018
Multiplexer Module
The 40/42-852A-018 is a PXI/PXIe 8-channel multiplexer with FC/APC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXIe-254, 6.6 GHz, 50 Ω, Solid-State, Dual 4x1 PXI RF Multiplexer Switch Module
780587-43
Multiplexer Module
PXIe, 6.6 GHz, 50 Ω, Solid-State, Dual 4x1 PXI RF Multiplexer Switch Module—The PXIe‑2543 features high-performance solid-state relays that offer unique benefits such as unlimited relay life and fast switching time. Front-mounted SMA connectors provide easy connection to your RF devices, and the module features termination on every COM line and channel.
-
Product
PXI Remote Mount Dual SP6T Multiplexer 2.5GHz 75, 1.6/5.6
40-785B-752-E
Multiplexer Module
The 40-785B range of PXI Microwave Multiplexers are available as a single or dual 6-channel panel mounted multiplexer with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI Prototyping Module, 1-Slot, 25-Pin D-Type
40-225A-301
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
500 MHz RF Multiplexer Plug-In Card
1260-150
Multiplexer Module
The Astronics 1260-150 is an RF multiplexer plug-in relay card for the Adapt-a-Switch™ carrier. It quickly and easily plugs into the front of the Astronics 1260-100 and 1260-101 Adapt-a-Switch™ VXIbus Carriers or Astronics 1256 GPIB/Ethernet and 1256L (LXI Core 2011 Compliant) switching mainframes.
-
Product
PXI High Voltage Power Multiplexer, Twelve 2:1 (SPDT)
40-331A-006
Multiplexer Module
The 40-331A-006 twelve 2:1 MUX is part of our range of 40-331A/332 High Voltage Power Multiplexer and Matrix Modules and is suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching.
-
Product
PC/104 Input/Output Module providing 96 lines of digital I/O
PCM-UIO96C-16
Digital I/O
The PCM-UIO96C-16 is a highly versatile PC/104 input/output module providing 96 lines of digital I/O. One important feature of this card is its ability to monitor 48 of the 96 lines for both rising and falling digital edge transitions, latch them, and then interrupt the host processor notifying that a change-of-input status has occurred. This is an efficient way of signaling the CPU of real-time events without the burden of polling the digital I/O.
-
Product
PXI/PXIe MEMS Optical Switch, Quad Insert/Bypass
40-860A-442
Multiplexer Module
The 40/42-860A-442 is a PXI/PXIe quad insert/bypass switch with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 8-Bank 40GHz SMA-2.9
60-802-408
Multiplexer Module
The 60-802-408 is a 4-channel, 8-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
640 Gb/s Digital Signal Processor
M8132A
Digital Signal Process
The M8132A is a powerful digital signal processing module featuring two customers accessible Xilinx Ultrascale+ FPGAs, four optical data interfaces (ODI) running at up to 160 Gb/s in+out each, and a PCIe Gen3 x8 link to the AXIe backplane. In addition, the module provides a trigger input and output, synchronization input and outputs for deterministic latency between compatible digitizers and AWG modules as well as a 10-general purpose I/O pins. The M8132A is part of Keysight’s Wideband Solution Platform that consists of a portfolio of compatible instruments, including digitizer, arbitrary waveform generator, digital signal processor and storage modules.
-
Product
PXI Monitored Multiplexer, Quad 25-Channel, 1-Pole
40-619-104
Multiplexer Module
The 40-619-104 is a high density PXI 2 A multiplexer module in quad 25-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
Product
Signal, Module, Receiver, QuadraPaddle, 90 Series, 192 Position, Fully Loaded w/ Twin Female Contacts & Square Posts for Wire Wrap (p/n's 610138200 & 610138118)
510150136
Receiver Module
Primary mating module 510151105. (May mate with other ITA modules, as well.)
-
Product
LXI Dual 2x2 Optical MUX LC Multi-Mode
60-851-405
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781775-01
Signal Module
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
LXI High Voltage Switching - 4-Bank, 1-Pole, 4:1 Multiplexer Plugin Module
65-231-713-HI
Multiplexer Module
High voltage multiplexer plugin module capable of cold switching up to 7 kV and hot switching up to 5 kV.
-
Product
RazorMax Express 16 CompuScope 16-Bit, 1 GS/s, PXIe Gen3 Digitizer / Oscilloscope
Digitizer
The GaGe RazorMax Express CompuScope PXIe Gen3 x8 digitizer features unprecedented speed and resolution with either four or two 16-bit channels at 1 GS/s and 600 MHz bandwidth, and PXIe Gen3 data streaming rates up to 5.2 GB/s in a 3U Single Slot PXIe form factor.
-
Product
PMC Module
PMC-1553-PLX
PMC Module
Operating temperatureCommercial: 0 to +70 °COptional: -40°C to +80°C• Airflow requirement: .5 CFM• Humidity: 5 to 90% (non-cond.)• Altitude: 0 to 20’000 ft
-
Product
LXI Microwave Multiplexer, SP4T, 6-Bank, 67GHz, 50Ω, SMA-1.85
60-803-806
Multiplexer Module
Our 60-803-806 is a 6 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 16-Bank 26.5GHz SMA
60-802-316
Multiplexer Module
The 60-802-316 is a 4-channel, 16-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXIe Microwave Multiplexer, Single SP6T, 26.5 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-785C-531-E
Multiplexer Module
The 40-785C-531-E (PXI) and 42-785C-531-E (PXIe) are single failsafe SP6T 26.5 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 50 GHz, 50 Ω, SMA-2.4, Terminated, Remote Mount, Failsafe
42-785C-552-TE
Multiplexer Module
The 40-785C-552-TE (PXI) and 42-785C-552-TE (PXIe) are dual failsafe SP6T 50 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber
40-852A-518-M50
Multiplexer Module
The 40/42-852A-518-M50 is a PXI/PXIe 8-channel multiplexer with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
LXI 8:1 Optical MUX SC/PC Single Mode
60-850-211
Multiplexer Module
Fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching
-
Product
PXI 8-slot BRIC Multiplexer, 64-Channel, 10-Pole (6 Sub-cards)
40-570A-414
Multiplexer Module
The 40-570A-414 is a 64-channel, 10-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
