Filter Results By:
Products
Applications
Manufacturers
Isolated Digital Output Modules
-
product
160 Channel Isolated Digital Output Module
DP-cPCI-3708
DP-cPCI-3708 provides 160 channels of Open-collector digital outputs supporting voltage levels from 5V to 35Vdc with 200mA current sink capability. The Darlington Open-collector transistors across each drive are suited for controlling relays, switches, external digital circuitry and other similar devices.
-
product
48 Channel Isolated Digital Input/Output Module
DP-VME-3078
DP-VME-3078 is a 48 Channel Isolated Digital Input Output Module. This module provides 48 input / interrupt channels and 48 digital output channels with isolation. The 48 channel inputs are divided into 12 groups, each group consisting of 4 channels and 1 common GND .The 48 output channels are divided into 6 groups, each group consisting of 8 channels and a common GND.
-
product
15-CH Isolated Digital Output Module
ND-6056
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
64 Channel Isolated Digital Input/Interrupt/Output Module
DP-VME-3636
DP-VME-3636 is a 64-Channel Isolated Digital Input/Interupt/Output Module. This module provides 32 channel digital input and 32 channel digital output with isolation. Channels are divided in 2 groups of 16 channels each and are routed to rear I/O. 16 non-isolated TTL channels are available.The module is used for digital interface, status setting, status monitoring, automatic test equipment, and high density industrial automation.
-
product
PXI 64-Channel Digital Output Module
40-412A-021
The 40-412A-021 (PXI) and 42-412A-021 (PXIe) are 64-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
product
96 Channel Isolated Digital Input / Interrupt Output Module
DP-cPCI-3096
96 Channel Isolated Digital Input / Interrupt Output Module
-
product
PXI-6713, 12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module
777795-01
12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6713 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6713 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
product
NI-9266, 8-Channel C Series Current Output Module
785047-02
8-Channel C Series Current Output Module - The NI‑9266 is ideal for interfacing and controlling industrial current-driven actuators. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9266 includes channel‑to‑earth ground isolation for safety and noise immunity.
-
product
8-CH 16-Bit PCI Express Analog Output Card
PCIe-6208
ADLINK PCIe-6208 series are 8-CH, 16-bit, PCI Express analog output cards which provide high resolution, high-density analog output functionalities and are suitable for ATE, signal generation, industrial process control, servo control and other industrial control applications.
-
product
Digital Output
VME-2170A
The VME-2170A optically coupled digital output board consists of VMEbus compatibility logic,data control logic, four 8-bit output registers, and 32 optically isolated high-level outputs. The board is implemented as a double Eurocard form factor PC board, and provides all necessary address decoding and data transfer control logic to accept both 8- and 16-bit data transfers. Optical couplers isolate the 32 outputs from each other and from the VMEbus.
-
product
PXI Analog Output/Current Loop Simulator Module - 16 Channel
41-765-001
The 41/43-765-001 is a PXI/PXIe 16-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
NI-9265, 4-Channel C Series Current Output Module
783733-01
4-Channel C Series Current Output Module - The NI‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
product
Digital Output Board
VME-2128A
VME-2128A 128-bit High-Voltage Digital Output Board with Built-in-Test
-
product
NI-9265, 4-Channel C Series Current Output Module
779334-02
4-Channel C Series Current Output Module - The NI‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
product
Analog Output PXI Card
GX1648
The GX1648 is a 3U PXI digital to analog output board is designed specifically for applications where multiple analog outputs are required. The GX1648 offers precision signal sourcing performance and quality at an economical price.
-
product
PXI-6723, 13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module
778998-01
13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module—The PXI‑6723 delivers low-cost, high-density analog outputs to meet a wide range of applications, such as stimulus-response, signal simulation, waveform generation, and actuator stimulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6723 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
product
PXI-6722, 13-Bit, 8-Channel, 800 kS/s PXI Analog Output Module
778999-01
13-Bit, 8-Channel, 800 kS/s PXI Analog Output Module—The PXI‑6722 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6722 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
product
PCI-6704, 16‑Bit, 32‑Channel, Static Analog Output Device
777306-01
The PCI‑6704 is a static analog output device that you can use for software‑timed voltage and current output applications.
-
product
PXI/PXIe Analog Output/Current Loop Simulator Module - 4 Channel
43-765-004
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
NI-9266 , 8-Channel C Series Current Output Module
785046-01
8-Channel C Series Current Output Module - The NI‑9266 is ideal for interfacing and controlling industrial current-driven actuators. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9266 includes channel‑to‑earth ground isolation for safety and noise immunity.
-
product
PXI/PXIe High Density Digital Input Module, 128-Channel, 50V
40-414-101
The 40-414-101 (PXI) and 42-414-101 (PXIe) are 128-channel digital input modules with 50 V inputs and provide a convenient way of determining the status of input lines by comparing the input voltage with two threshold voltages - quickly establishing if the input is low, high or in an intermediate logic state.
-
product
4/8-CH 12-Bit 1 MS/s Analog Output Multi-Function PXI modules
PXI-2500 Series
ADLINIK PXI-2501 and PXI-2502 are high-speed, high-performance analog output multifunction PXI modules. These devices are able to update up to 8-CH, 12-bit analog outputs imultaneously sustaining 1 MS/s. The reference sources and output polarities are programmable individually per channel. Combine this with the multiplying PXI architecture, ADLINK PXI-2500 series PXI modules can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory. The PXI-2500 series integrate up to 8-CH, 400 kS/s, 14-bit single-ended analog inputs with programmable polarity, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timer/counters.
-
product
Analog Output PXI Card
GX1642
The GX1642 is a 3U PXI digital to analog output board is designed specifically for applications where multiple analog outputs are required. The GX1642 offers precision signal sourcing performance and quality at an economical price.
-
product
PXIe 64-Channel Digital Output Module
42-412A-021
The 40-412A-021 (PXI) and 42-412A-021 (PXIe) are 64-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
product
PXIe-4322, 16-Bit, 8-Channel, 250 kS/s Ch-Ch Isolated PXIe Analog Output Module
782878-01
16-Bit, 8-Channel, 250 kS/s Ch-Ch Isolated PXIe Analog Output Module—The PXIe‑4322 is a channel‑to‑channel isolated analog output module with integrated signal conditioning. The device provides accurate, simultaneous dynamic voltage and current outputs. By combining signal conditioning and D/A converters on the same device, the PXIe‑4322 isolated analog output module delivers a smaller footprint and higher measurement performance. In current mode, the module operates in all four quadrants, so you can both sink and source current. Isolation and higher voltage and current outputs make this module ideal for automotive applications.
-
product
Digital Output Board
VME-2533
VME-2533 32-bit Differential Digital Output Board. VMEbus specification compatible double height form factor.
-
product
PXI/PXIe High Density Digital Input Module, 128-Channel, 50V
42-414-101
The 40-414-101 (PXI) and 42-414-101 (PXIe) are 128-channel digital input modules with 50 V inputs and provide a convenientway of determining the status of input lines by comparing the input voltage with two threshold voltages - quicklyestablishing if the input is low, high or in an intermediate logic state.
-
product
Combo Unit, 7.5 Digit Digital Multimeter (DMM) with 10-Bit 1GHz Digitizer in a Single VXI Slot
6084A
Increases test system performance and density with this combo unit, which packages a 7.5 digit Digital Multimeter (DMM) together with a 10-bit, 1 GHz Digitizer into a single VXI slot.Replaces the Wavetek 1362 DMM, Analogic DBS Series, and Agilent VXI DigitizersDigitizer with 4 Inputs, 10-bits, 1 GHz, up to 4 GS/s and Ranges up to 500V DMM with 7.5 Digits for DC Volts, Current and Ohms with AC Volts up to 1 MHzIVI-COM Drivers and Soft Front Panels ProvidedMore Dynamic Range (by 20 dB for DMM and 12 dB for Digitizer) for Better Legacy Range Mapping
-
product
PCIe 16 Bit High Speed Digitizer - 250 MS/s on 4 Channels
M4I.4421-X8
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
PXIe-5622 , 150 MS/s, 16-Bit PXI IF Digitizer
780412-02
150 MS/s, 16-Bit PXI IF Digitizer—The PXIe‑5622 includes onboard signal processing (OSP), which enables features such as quadrature digital downconversion (DDC), real DDC, and anti-alias filtering. The PXIe‑5622 is ideal for communications applications because of its high dynamic range front end and a high-throughput PXI Express interface that allows it to stream IF data to disk for hours at the full sample rate.
