Battery Internal Resistance Testers
See Also: Resistance Test, Battery Conductance Testers
-
Product
CellCorder Battery Tester 'EU Series'
CRT - 400
-
The new CRT-400 is the latest version in the leading line of CellCorder battery test instruments. Lightweight, stylish, rugged and durable. Special features include new user-friendly operation, USB and IR data transfer, modem, graphical reflective LCD display for better contrast, and new cables and clamps.
-
Product
Digital Battery Tester with Automatic Test
706
-
Controlled by microprocessor, simply activate the switch once and the #706 applies a precisely timed, 10 second load to the battery. The test results, “OK”,“WEAK” or ”BAD” are then displayed along with the test voltage, until the unit is disconnected. The #706 also tests charging voltage and relative starter current draw.
-
Product
Intelligent Battery Charger-Analyzer for Battery Systems
SuperMini
-
The SuperMini is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMini can satisfy the requirements of most ( Up to 40 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
Product
Battery Tester
G5.BT
-
The G5.BT series is bidirectional regenerative. It was developed specifically for testing energy storage devices and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The G5.BT series has an outstanding current accuracy of <0.02% FS, an additional high-resolution current measurement range, and a fast current rise time in the 100 μs range. Ripple modulation, an integrated safety relay for PL c according to EN ISO 13849 and a powerful CAN multi-protocol interface (1 kHz, 16 bit) as well as functions to avoid reverse-polarity problems, current surges, and unwanted deep discharges make the G5.BT series the ideal, versatile battery module and battery pack tester.
-
-
-
Product
Battery Module
BAT-200
-
The Battery module supplies power to a sensor, or chain ofsensors, operating in the Off-Line mode, and to sensors connectedto an RF communication module.The Battery module can be recharged by connecting it to the PC'sUSB socket via the USB module's USB cable.
-
Product
3 Wire (Digital) Earth Resistance Tester
1120 ER
-
Standard Electric Works Co., Ltd
● Waterproof: IP54● Capable of measuring earth resistance and earth voltage● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test● The test leads are supplied as standard accessories for simplified two-wire measuring system● 0Ω adjustment● Battery operated● Data hold function● Low battery indication
-
Product
Battery Tester
BAT-250
-
The Amprobe BAT-250 Battery Tester is designed for one-handed, comfortable and reliable battery measurements. The uniquely designed tester offers an ergonomic slider and a v-shaped side cradle to better hold batteries in place during testing and a contoured case shape that fits neatly in your hand. Testing your batteries has never been easier.
-
Product
Clamp Earth Resistance Testers
-
Is used for earth resistance test. This meter uses an EBTN screen with a dual display function (the resistance & current displayed). It also has functions such as a real-time clock, data storage, data review, alarm, and automatic shutdown.
-
Product
Ground Resistivity and EarthService Tester
AD-510
-
Large, readable LCD display (2000 counts), Instant battery life indicator, Test frequency: 128 Hz (quartz generator), Test Voltage: max 30 V peak-to-peak, Range: 0,01 W ? 2 k W. Accuracy resistance measurement: 1 % 2 digits,
-
Product
20V Battery Internal Resistance/Voltage Tester
TOB-BVIR
-
Xiamen Tob New Energy Technology Co., Ltd
Portable Internal Resistance Tester for All Batteries 0 - 20V With Charging Adapter. TOB-BVIR Battery internal resistance tester can be used for measuring the Internal Resistance and Open CircuitVoltage of almost all of the commercial batteries such as Secondary battery, Lead acid battery, Nickle cadmium, Nickle-metal Hydride and Li-ion battery.
-
Product
Battery Testers
-
designed to accurately measure the internal impedance of a single cell or battery stack with voltages as high as 80 V. In addition to impedance, auxiliary measurements include voltage, current, phase, capacitance, inductance, quality factor and more.
-
Product
Lead Acid Intelligent Battery Tester
612
-
This digital battery tester is designed for testing 6V and 12V standby SLA, cyclic GEL and car FLOODED batteries. Simple in operation, the ACT 612 simulates a full 20 hour (C20) discharge test in seconds and displays the DC Voltage results and Ah capacity available.
-
Product
Durable Hand-Held Battery Tester
6029
-
• Test 6 & 12 Volt batteries, alternators and starters• 125 Amp fixed load• Made in USA of US and Global Components
-
Product
Heavy Impact Tester, Battery Safety Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's battery impact tester tests the safety of the battery through different weights, different heights and different impact areas. After a series of tests on this battery impact tester, the battery must not have flame or explosion.
-
Product
Battery Chargers
-
The JUNXY intelligent battery charger covers three charging processes: (1)Constant current charging → (2)Constant voltage with decreasing current charging→ (3)micro current floating charging. Auto shut-down when reach any one of four charge cutt-off settings: (1)cell voltage, (2)charge duration, (3)charge capacity, (4)manual stop charge. It is especially designed for battery bank maintenance for different industries with nominal voltages: 24V, 36V, 48V, 80V, 96V, 110V/120V, 220V/240V, 380V etc with different charging current.
-
Product
Advanced Battery Tester
DBT-12+
-
The tester enables safe measurement of voltage, current rating, state of charge and state of health for 12V and 6V batteries. The device is powered by an internal battery, so it can test even discharged batteries and can be conveniently used as a voltmeter.
-
Product
Battery Discharger & Capacity Tester
IDCE-8X0
-
Fuzhou Fuguang Electronics Co., Ltd.
Wide Range: IDCE-8X0CT series can cover 10V~480V for multiple batteries test requirements like telecom (48VDC), powerutilities (110VDC, 220VDC), UPSs (300-60 VDC), traction batteries(12-96VDC)etc.
-
-
Product
Battery Management
-
Renesas' automotive-grade (AEC-Q100) Li-ion battery management solutions (BMS) are specifically designed to meet the stringent safety, reliability and performance requirements of next generation electric vehicle applications.
-
Product
Battery Gauges
-
Global Digital Instruments, LLC
Our battery fuel gauges and LED volt meters are designed to monitor the charge capacity of DC powered equipment and monitor information about the equipment's electrical system.
-
Product
Resistance Software
OhmRef
-
OhmRef provides the power of automation for Standards maintaining statistical control of resistance values in your laboratory. This program controls a Low Thermal Scanner along with other equipment commonly available in Standards Laboratories to compare resistance standards over the range of 100µΩ to 10GΩ . Comparison accuracies arebetter than 1 ppm in the midranges.
-
Product
Automatic Battery
BATLV400
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
Product
Battery Tester Battery Test Machine
2523
-
Shenzhen Chuangxin Instruments Co., Ltd.
With Chuangxin’s experience in impedance test and marketing survey, the new battery tester-TH2523 is successfully launched. It can be competitive with other similar products with its outstanding performance, easy operation and new look.
-
Product
Resistance Meter
MS8-2L
-
M-module MC8-2L is a mezzanine module designed to measure resistance using a two-wire measurement scheme in eight channels (eight-channel digitizer). М-module МС8-2Л is installed on the mezzanine carrier - NM module and is connected to it via a local information highway. Up to four m-modules of various types can be installed on the HM module. The NM module, together with the m-modules installed on it, forms a VXI module of size C-1 and is used to create information measuring VXI systems.
-
Product
Artificial Resistive Load
326
-
An industry staple for over 50 years, the TESCO Artificial Resistive Load (Catalog No. 326) has been redesigned to meet 21st century standards, making it the most cost effective, portable and light weight artificial load box on the market today.
-
Product
Surface Resistance Tester
MR – 1
-
The different specific resistances are specified by selecting one of the pre-programmed materials, or by measuring the specific resistance of unknown materials and entering the result. Preferably the coat thickness is displayed, but the measurement and display of the actual resistance, the square resistance and the specific resistance is possible, too. All measured values can be transmitted into a PC via a serial interface. Controlling the MR-1 on the other hand is not possible.
-
Product
Battery Tester
700
-
The #700 has an internal loading capacity of 100 amps. It is a great tool for finding batteries that can’t stand up to the load of today’s automotive accessories. It will also test relative starter current draw and charging voltage.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, 1 kV Isolation
41-752A-111
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
