Mil-Std-1553
Interface Standard for Digital Time Division Command/Response Multiplex Data Bus
See Also: MIL-STD, 1553, Mil-Std-1760
-
product
3.6 GS/sec Ultra Wideband RF/IF Extreme 1/2 ATR Recorder
Talon RTX 2589
- Rugged 1/2 ATR MIL-spec chassis- Designed for harsh mechanical and thermal environments- Environmentally sealed- Internally conduction-cooled- Fully sealed for RF emissions with EMI power line filter- MIL-STD circular connectors- Compact and lightweight design - 22 lb (10kg)- Ideal for UAVs, military vehicles, aircraft pods and outdoor environments- Capable of recording RF/IF frequencies to 2.8 GHz- Ultra Wideband recording with 3.6 GHz 12-bit A/D- Selectable 1.8 GHz dual channel mode- Up to 61 TB of solid state storage in removable QuickPac- Sustained real-time record rates up to 4 GB/s- 12 to 28 VDC power supply- Optional GPS receiver for precise time and position stamping- SystemFlow API, GUI and Signal Viewer analysis tools- Optional telnet remote connection to recorder
-
product
8" Cable
CONW1553-1
Transitions from a card end connector (with IRIG) on the QVME-1553 or QVXI-1553X into two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends, and four 8" cables with BNC cable jacks for I/O triggers and IRIG Rec/Gen.
-
product
Micro Coax, Contact, ITA, RG316 Double Shield
610141104
Primary mating contact 610140104. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - SolderInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC – 10.5 GHzVSWR 1.0225 +.05 f(GHz)Insertion Loss – √f(GHz) x .06 dBDWV 800 V RMSContact Resistance 6 mOhms center/4 mOhms outer Cable Specifications RG316 Double ShieldEnvironmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
Satellite & Payload Check-Out Systems
Rovsing delivers systems for complete satellite or satellite subsystem testing. Rovsing has developed a modular test system architecture, based on S/W and H/W modules developed by Rovsing for most common space interfaces such as Power, TM/TC, MIL-STD-1553B and SpaceWire. A dedicated test system can then be composed by configuration of the modular architecture, installation of monitoring and control software, as well as test definition and scheduling software as required. Besides reduced development time, this has the advantage that the system to a large extent consists of elements that have been validated on previous missions.
-
product
Low Phase Noise Amplifiers
Pasternack's low phase noise amplifiers cover select frequency bands ranging from 1.5 to 18 GHz with residual phase noise levels as low as -180 dBc/Hz @ 10 KHz offset. Additional performance specs include small signal gain ranging from 9 to 14 dB, with typical noise figure of 5.5 dB. Psat levels for these amplifiers range from +16 to +25 dBm with Output IP3 levels as high as +34 dBm. All models feature single DC voltage supplies and input/output RF ports are internally matched for 50 ohms with DC blocking capacitors. These compact module assemblies require no external components and are available in rugged Kovar metal drop-in packages that are gold-over-nickel-plated and support field replaceable SMA connectors. All models are EAR99 and guaranteed to meet MIL-STD-883 test conditions for hermeticity and temperature cycle.
-
product
AC Power Sources
GUPS (Global UPS)
AMETEK Programmable Power, Inc.
Elgar GUPS are ruggedized on-line "UPS's" that accept a broad range of worldwide utility and military AC input power. Without operator intervention, they automatically select the appropriate input power ranges to accommodate global operation. The GUPS Series has been specifically designed to withstand the rigors of mobile applications. They meet the vibration and shock requirements as specified in MIL-STD-810E, Methods 514.4 and 516.4. Their rackmounted aluminum chassis with stainless steel hardware withstands harsh environments and provides a strong, light weight enclosure.
-
product
Bus Monitor/Differential Scope Output
BT3-USB-MON
The BT3-USB-MON is like a Swiss Army Knife for MIL-STD-1553 users making it a must have, easy to use lab tool for anyone developing, troubleshooting, or maintaining a system that uses MIL-STD-1553. The monitor only bundle combines three tools into one easy to use product: 1553 visualization and recording with user friendly GUI BusTools-1553-BM; 1553 monitoring hardware; and an integrated differential scope output for electrical analysis - all available at an accessible price point.
-
product
Bus Controller
CPCI-1553-1
Single or dual UTMC 1553 Summit Controller, Bus controller, Remote terminal, Bus monitor modes.
-
product
Linear Rack Mount Power Supplies Current Stabilizers, Programmable, Local/Digital/Analog Control, Ultra Low Ripple/Noise
Series CC
These current stabilizers with built-in, dual range current-sensing resistors and a full complement of meters and controls, are 1/6-rack size units designed to plug directly into their own carrier cases and rack adapters. These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
product
Interface
RXMC1553
Abaco Systems’ RXMC-1553 is the latest generation of performance and flexibility for MIL-STD-1553A/B Notice II on a XMC.0 Mezzanine Card. With one or two dual-redundant channels, the RXMC-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
product
Intelligent Interface Card
IIB-1553-PC104+
The IIB-1553-PC104+ is an intelligent interface card giving full MIL-STD-1553 test, simulation and bus analysis capability on the PC104+ bus, providing 1553A, 1553B, McAir and STANAG 3838 variants in a single card. The IIB-1553-PC104+ supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
product
ACC-188 Synchronous Serial Radio Adapter
The ACC-188 synchronous serial radio adapter is interoperable among various tactical radio brands and models used by the defense community. The ACC-188 works with any radio that has a synchronous serial communication port using MIL-STD-188-184 and enables the tactical radios to send data such as GPS maps, images, coordinates, and IM-type communications.
-
product
Ferroresonant Power Supplies
Series PRM
These units are modular ferroresonant MIL-STD-461-compliant voltage stabilizers which obtain their source-isolated, overload-protected output from Kepco's proprietary transformer, Flux-O-Tran. This design lends itself to custom volt-ampere combinations, consult factory.
-
product
Interface Card - 1-2 Channels of MIL-STD-1553 Networks on a PMC Form Factor with Ethernet Backplane Interface
PMCE-1553
PMCE-1553™ is an innovative product that provides 1553 operations via 10/100/1000 Ethernet IP/UDP local area networks (LAN) backplane. PMCE-1553 is a standard PMC form factor card, but instead of PCI backplane, PMCE-1553 uses the P4 connector for Ethernet based control and communications.
-
product
Mini PCI Express Interface Card
MPCIE-1553
The MPCIE-1553 is a mini PCI Express Full-Mini Type 2 Interface Card for MIL-STD-1553 networks. Coupled with AltaAPI Represents the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software - in an amazingly small package.
-
product
Aerospace Interfaces
Aerospace InterfacesDecode and visualize data from ARINC 429, MIL-STD-1553, IRIG CHAPTER 10, iNET and IRIG Chapter 4 PCM telemetry data interfaces.
-
product
Altitude Testing
Our environmental testing facilities simulate altitude testing from -400 ft. (-121 meters) to outer space at 100,000 ft. (30,480 meters) or up to 10-6 Torr (1.3e-7 kPa) with temperature applied as low as -300°F (180C). We can reach these heights within 5 minutes or less. We are capable to handle products measuring up to 4ft X 4ft X 8ft to many standards, including MIL-STD-810 and RTCA DO-160.
-
product
Fiber Channel Simulyzer
Avionic Interface Fiber Channel SimulyzerTM products are multifunctional, high-performance Fiber Channel interface and test boards. The products have both a data generation / simulation function and a monitor / analysis function on one board. Avionic Interface Fiber Channel products can be used with the most popular upper layer protocols FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All FibreChannel products use multiple processors with large onboard RAM.
-
product
ARINC 429 Simulator & Analyzer Applications Software
F-SIM-A429
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 429 InterfacesCapture & Analyze Data from Multiple ARINC 429 Input ChannelsDefine & Execute Complex Simulations of Multiple Rate-Oriented Labels - Simulate Output Data on Multiple Channels Simultaneously - Replay Previously Captured Bus Data - Full Error Injection & Detection - Update, Modify, & View ARINC 429 Data on-the-fly - Engineering Unit Displays & Software Widgets - Receive Data to Label/SDI Specific Buffers - Also Supports MIL-STD-1553, ARINC 664, Ethernet, & Data Load operations
-
product
Five Channel Amplifier
Teledyne RF & Micrrowave designed the Five Channel Amplifier specifically for a custom space application. Each independent channel used dedicated RF Input/Output and DC bias connections. Each channel's RF performance was tailored differently to meet the application requirements. All components were manufactured and screened per MIL-PRF-38534, Class K. Additionally, to meet mission requirements The top assembly was also tested for RF and DC parameters during MIL-STD-202 thermal cycling and random vibration environments. This effort required disciplined development, manufacturing and program management efforts to meet challenging mechanical and RF engineering requirements.
-
product
Ethernet Bridge Converter for MIL-STD-1553 and ARINC
ENETX-MA4
eNetX-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNetX-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 4 ARINC channels. Tested to MIL-STD-704F/810G/461F and DO160.
-
product
Hybrid LX
HLX Series 0.8” x 0.8” x 0.15”
*Surface Mount Package *Ruggedized, Hi-Rel *Hermetically-Sealed per MIL-STD-883 *Extreme Shock and Vibration Tolerance *Output Power to +14 dBm Available
-
product
Single Or Dual Stream MIL-STD-1553 A/B &4, 8 Or 12 Channel ARINC429 Mixed ProtocolTest & Simulation Module For Standard Ethernet
ANET-MxAy
Single or dual stream MIL-STD-1553 A/B and 4, 8 or 12 channel ARINC429 mixed protocol Test & Simulation module for standard Ethernet. The ANET embedded Linux operating system gives the unique capability to run the optional PBA.pro Engine right in the box.Another option is the ANET-ADK onboard software development kit where users create runtime applications (e.g. MIL-STD-1553 to Ethernet Converter / ARINC429 to Ethernet Converter , MIL-STD-1553 to Ethernet Gateway / ARINC429 to Ethernet Gateway) to execute right in the box. For wireless applications an ANET compatible USB Wifi dongle is optionally available. The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET docking station to host up to 4 ANET modules.
-
product
Interface Card
XMC-1553
The XMC-1553 Interface Card and AltaAPI Represent the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software. Ideal for SBCs or carriers for VPX, VME and cPCI (Compact PCI/PCIe or PXI) - Commercial or Rugged/Conduction Cooled Systems.
-
product
Multi-Channel, Multi-Protocol 1553, ARINC, WMUX Interface for 3U PXIe
Alta Data Technologies’ PXI Express interface modules offer a wide range of MIL-STD-1553, ARINC and WMUX configuration options using Alta’s PMC cards on a single-slot PXI Express 3U carrier. The cards are based on the industry’s most advanced 32-bit FPGA protocol engines, AltaCore™, and by a feature-rich application programming interface, AltaAPI™ (with LabVIEW SDK).
-
product
Pulse generator
9355-1
Solar Model 9355-1 Pulse Generator is designed to provide impulse excitation by means of an injection probe placed around interconnecting cables or power wires. The unit uses a charged transmission line (50 ohms) to generate a pulse with less than 2 nanoseconds rise and fall time, and duration of approximately 30 nS, calibrated in a 50 ohm fixture to deliver up to 5 amperes at a rate of 30 p.p.s. for one minute as required by MIL-STD-461D/E, test method CS115.
-
product
Data & Protocol Converter
uMACC
The uMACC is a wholly contained Communications Converter (data converter - protocol converter or translator). Its small size makes it a complete solution for developing & testing both in the lab and in the field.The uMACC can carry up to 4 modules. Each module can be one of the following protocols: 1 dual redundant MIL-STD-1553/1760 interface1 H009 channel5 MMSI channels5 ARINC-429 channels2 ARINC-708 channels2 ARINC-717 channels5 ARINC-825 (canbus) channels2 Serial channels (RS-232/422/485, NMEA 0183)Ethernet (10/100/Gigabit)10 Discrete I/O signalsAnalog to Digital / Digital to Analog
-
product
PMC Module
PMC-1553-PLX
Dual UTMC 1553 Summit Controller, Bus Controller, Remote Terminal, Bus Monitor Modes
-
product
500 Watt AC/DC Power Line Conditioner, 3U VPX, Holdup Time
VPX56-3HU
NAI's VPX56-3HU is a rugged, high-performance 500-Watt Output +28 VDC Input 3U VPX AC/DC Power Line Conditioner designed for aerospace, defense, and industrial markets. This off-the-shelf power supply plugs directly into a standard VPX conduction cooled chassis and protects downstream DC-DC converters from MIL-STD-704 transients, low-voltage conditions and power interruptions, providing up to 50 milliseconds of holdup time at up to 500-Watts. Continuous Background Built-In-Test (BIT) and I2C communication are included.
-
product
Salt Spray Chambers
MX-9200
LR Environmental Equipment Co. Inc.
A high reliability thermostatic temperature controller maintains the salt solution at a preset controlled temperature in a reservoir within the double wall construction. The salt solution is introduced into the chamber through an atomizing nozzle. The nozzle can be calibrated by us to perform to MIL-STD-19500B, paragraph 40.8 and other specifications. This specification requires that a salt residue be deposited on the specimens, in addition to generating salt fog atmosphere.
