PXI DAQ
-
Product
PXI MUX 1-Bank of 80 Channel 1-Pole
40-615-021-1/80/1
-
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
PXI 24 Channel High Voltage Multiplexer
40-320-101
-
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
PXI Multiplexer, Single 16-Channel, 4-Pole
40-630A-022-16/4
-
The 40-630A-022-16/4 is a single 16-channel, 4-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI Semi-Dynamic Digital I/O Module, 48-Channel
40-419-002
-
The 40-419-002 is a 48-channel digital I/O module suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. It can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
Product
Arbitrary Function Generator PXI Card
GX1200/GX1201
-
The GX1200 and GX1201 are high performance, single-channel PXI arbitrary waveform generators that combine a function generator, arbitrary waveform synthesizer, programmable sequencer, pulse generator, and modulation generator in one instrument. The GX1200 Series delivers all this at a lower cost than comparable benchtop or VXI-based instruments.
-
Product
PXI Prototyping and Breadboard Modules
-
The breadboard modules with digital I/O (the 40-220A series) allow the user to construct their own circuit in situations where a PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include creating custom circuitry that can be housed on a 3U board or to build special “one-off” switching modules.
-
Product
PXI Single 33x16 Matrix, 1-Pole
40-542-021
-
The highest density single slot PXI reed relay matrix module on the market today. This range also includes a 132x4 and 66x8 reed relay matrices with 1-pole switching. They are constructed using high reliability sputtered ruthenium reed relays, offering >10e9 operations to give maximum switching confidence with long life and stable contact resistance. Typical applications include signal routing in Functional ATE and data acquisition systems.
-
Product
PXI Remote Control Module
-
PXI Remote Control Modules allow direct control of PXI and PXI Express Systems through PCs and laptops. You can choose between copper (up to 10 m) or fiber-optic (up to 200 m) cable that connects to PXI or PXI Express modules in slot 1 of your PXI system.
-
Product
PXI SMU/Power Supply Instrument
-
a programmable PXI-Express DPS (Device Power Supply) Card designed for high-accuracy and reliable output power for device test applications. Its compact size, easy level of integration, and high flexibility make the 52310e Series ideal for multi-channel power supplies.
-
Product
PXI Power Relay Module, 12xSPST, 16 A
40-161A-002
-
The 40/42-161A-002 is a PXI/PXIe 12xSPST power relay module and is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock. Electro-mechanical power relays are used wich are suitable for switching loads up to 16 A at 250 VAC.
-
Product
PXI Analog Output / Current Loop Simulators
-
These modules are aimed at simulating industrial control transceivers, utilizing 4–20mA current loops. The modules include built-in relays for shorts and opens functionality enabling fault insertion testing on every channel and also enable slew rates to be programmed so that different sensors can be effectively mimicked.
-
Product
PXI Monitored Multiplexer, Dual 32-Channel, 1-Pole
40-619-202
-
The 40-619-202 is a high density PXI 2 A multiplexer module in dual 32-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
Product
PXI Pull-Thru Adapter, Double Slot, 6.75"
510109566
-
The PXI Pull-Thru Adapter can house discrete wiring that connects from a VPC i2 MX Receiver module to a PXI card. The Adapter has a removable side plate and thumb tabs for easy removal from the Receiver frame. Accepts all i2 MX Receiver modules.
-
Product
PXI Prototyping Module, 1-Slot, 50-Pin D-Type
40-225A-501
-
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI Chassis, 8-Slot
40-924-001
-
The 40-924 includes all the features and performance required by the PXI standard and supports a control interface or embedded controller and up to 7 additional 3U peripheral modules.
-
Product
PXI 3x3 10GHz Matrix with Termination
40-787-518-3X3-T
-
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scaleable non-blocking or blocking microwave matrix for frequencies to at least 20GHz.
-
Product
PXI 5A Fault Insertion Switch 10-Channel
40-196-001
-
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
Product
High Density Switching PXI Card
GX6138
-
The GX6138 is low cost 3U switching card with 38 individual low level SPST Form A relays capable of switching 0.5 A at 200 VDC. The GX6138 is ideal for applications requiring high density switching.
-
Product
PXI Power Multiplexer, 16-Channel, 2 Pole
40-650A-002
-
The 40-650A-002 is a PXI 16 Channel Power Multiplexer, suitable for switching inductive/ capacitive loads up to 5A at 250VAC.
-
Product
PXI 3x3 20GHz Matrix
40-787-528-3X3
-
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module.
-
Product
PXI 12x4 Matrix, 1 Pole Screened
40-510-021-S
-
The 40-510 series of matrix modules feature a wide range of selectable switching configurations (12x4,dual 12x4,12x8 and 24x4). Typical applications include signal routing in ATE and data acquisition systems. Available reed relay formats are 1-pole, 2-pole and 1-Pole screened. The screened version is suitable for switching signals up to 50MHz. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules.
-
Product
PXI RTD Simulator Module 12-Channel PT1000
40-262-202
-
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
Product
PXI Chassis And Remote Controllers
-
We offer both PXI & PXIe chassis and controllers that support all of our PXI switching and simulation modules as well as those from third parties. There is a choice of up to 21-slot 3U chassis with options to reduce acoustic noise and modules that can be powered from a DC source.
-
Product
PXI High-Density General Purpose Switch Modules
-
Our PXI high-density general purpose switches provide an ideal solution for applications requiring dense arrays of uncommitted relays.All reed relay modules use high-quality sputtered ruthenium relays that exhibit excellent contact performance under low and medium level switching conditions. Do you have a general purpose application that requires high power handling? We also have electro-mechanical modules that are ideal for just these situations.
-
Product
PXI Prototyping Module, 2-Slot, 15-Pin D-Type
40-225A-602
-
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI Switch Solutions
-
Over 1,000 PXI switch modules available, we can help you with your test and measurement requirements. Our PXI switch modules, available in PXI and PXIe formats, range from the highest density switching matrices (BRIC), RF and optical switching to fault/signal insertion modules.
-
Product
PXI Semi-Dynamic Digital I/O Module, 16-Channel
40-419-004
-
The 40-419-004 is a 16-channel digital I/O module suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. It can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
Product
VXT PXI Vector Transceiver
M9411A
-
5G ready PXIe VXT - vector signal generator and vector signal analyzer - offers 1.2 GHz instantaneous bandwidth, custom FPGA, and optical I/O.
-
Product
PXI-2532B, 512-Crosspoint PXI Matrix Switch Module
782383-01
-
512-Crosspoint PXI Matrix Switch Module—The PXI‑2532B is a high-density PXI matrix switch module built to serve high‑channel‑count automated test systems. Featuring compact reed relays with switching speeds up to 2,000 cycles/s, the PXI‑2532B can be configured in more than 10 matrix topologies by using different terminal block accessories. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
PXI 2A Multiplexer, 16-Bank, 4-Channel 2-Pole
40-614-002
-
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
