PXI DAQ
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781339-03
-
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
VXI To PXI Transition Products
PXI/cPCI Carrier
-
The VX407C is an intelligent VXI carrier that allows PXI and cPCI modules to be used in VXI systems.
-
Product
PXI 5A Power Multiplexer, 1-Bank, 48-Channel, Independent Isolation
40-651A-101
-
The 40-651A-101 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats.
-
Product
PXI BRIC8 FIBO Matrix Dual 24x4 3pin brkout
40-595A-009
-
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
-
Product
PXI 8-Slot BRIC Matrix, 115x16, 1-Pole (5 sub-cards)
40-560B-121-115X16
-
The 40-560B-121-115x16 is an ultra high density matrix module and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-054-HI
-
The 40-230-054-HI (PXI) and 42-230-054-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 22.05MΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 62.1Ω
40-252-011
-
The 40-252-011 is a programmable resistor module with 4 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
4-Slot BRIC, 256x4, 1 Pole, PXI Matrix (2 Sub-cards)
40-559-401-256x4
-
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-036-HI
-
The 40-230-036-HI (PXI) and 42-230-036-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 395kΩ with 8Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI Triple SP4T Multiplexer 40GHz 50 SMA-2.9
40-784A-143
-
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
Product
PXI 12-Slot BRIC Matrix, 588x6 1-Pole (7 Sub-cards)
40-558-121-588X6
-
The 40-558-121-588x6 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI 4-Slot BRIC Matrix, 44x8 1-Pole (2 Sub-cards)
40-562B-021-44X8
-
The 40-562B-021-44X8 is a high density BRIC4 matrix module with a size of 44x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
8-Slot BRIC, 256x4, 1 Pole, PXI Matrix (2 Sub-cards)
40-559-801-256x4
-
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI 12-Slot BRIC Matrix, 352x8 2-Pole (16 sub-cards)
40-562B-322-352X8
-
The 40-562B-322-352X8 is a high density BRIC12 matrix module with a size of 352x8 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 125 MS/s on 8 DAQ Channels and 8 AWG Channels
DN2.806-08
-
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
PXI 1A Fault Insertion Switch 22-Channel
40-195-001
-
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
Product
Octal 4 To 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-761A-008
-
The 40-761A-008 terminated octal 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
4- Channel PXI Source Measure Unit (SMU)
GX3104
-
The GX3104 is a precision 3U PXI module that forces and senses both voltage and current over a range of ±20 V and up to ± 1 A ( channel 1) with channels 2- 4 capable of supplying up to 500 mA. Total available output current from the module is 1A. The four channels are electrically isolated from the PXI power supply and share a common, isolated ground.
-
Product
PXI 12-Slot BRIC Matrix, 121x16 1-Pole (11 sub-cards)
40-562B-321-121X16
-
The 40-562B-321-121X16 is a high density BRIC12 matrix module with a size of 121x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI RTD Simulator Module, 24 Channel, PT1000
40-263-003
-
The 40-263-003 is a 24-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
128-Channel Scanner/Multiplexer PXI Card
GX6264
-
The GX6264 is a 6U PXI scanner / multiplexer that plugs directly into an PXI or CompactPCI backplane. The GX6264 provides either differential or single-ended scanning capability, configurable via software commands or DIP switches.
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 8 Channel
41-761-004
-
The use of two wire outputs and isolation from ground ensures that the 41-761 can be used to accurately simulate low voltages even in the presence of common mode voltages in the system. Each Vcold connection is independent permitting the 41-761 to be connected to multiple cold junctions.
-
Product
PXI 8 Slot BRIC 525x4 2A 1-Pole Matrix
40-568-107
-
The 40-568 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 200VDC/140VAC. The 40-568 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI 2 Amp Multiplexer, Single 8-Channel, 8-Pole
40-635A-004
-
The 40-635A-004 is a single 8-channel, 8-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI 8-Slot BRIC Matrix, 484x4 2-Pole (11 sub-cards)
40-562B-122-484X4
-
The 40-562B-122-484X4 is a high density BRIC8 matrix module with a size of 484x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A
40-194A-002
-
The 40-194A-002 is a 7-Channel Fault Insertion switch with two fault buses, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
Product
PXI High Density Precision Resistor Module, 4-Channel, 3Ω to 6.97kΩ
40-298-130
-
The 40-298-130 is a high density programmable resistor module with 4 channels which can be set between 3Ω and 6.97kΩ with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI Single 32x8 Matrix Card, 1 Pole
40-530-021
-
Typical applications for this high-density reed relay matrix include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability Sputtered Ruthenium Reed Relays, offering 109 operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules. For example, seven PXI modules will form a 224x8 Matrix, a total of 1792 crosspoints in a 7-slot PXI Chassis.
-
Product
PXI 100 x Normally Closed Relay 1A 60W
40-145-201-NC
-
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector.
-
Product
PXI 2A Multiplexer, 4-Bank, 32-Channel, 1-Pole
40-614B-006
-
This 4-bank, 32-channel, 1-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
