PXI DAQ
-
Product
PXI Ethernet Interface Module
-
PXI Ethernet Interface Modules equip PXI systems with high-bandwidth Ethernet-based connectivity with up to 40 Gb/s data rates per port. Featuring compatibility with industry-standard network and automatic cable polarity detection, these modules are ideal for high-performance data transfer and vision applications on the PXI platform. These modules have independent bandwidth to support two GigE Vision cameras with Power over Ethernet (PoE).
-
Product
PXI 4 Slot BRIC 90x16 1-Pole (6 sub-cards)
40-561A-021-90X16
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1.5Ω to 925Ω
40-251-021
-
The 40-251-021 is a programmable resistor module with 4 channels which can be set between 1.5Ω and 925Ω with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI Load Resistor Module 40 Ohm to 295 Ohm
40-292-011
-
The 40-292 module is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors. The short circuit position is fully thermally protected and provides a short circuit current limit. The series open switch provides an automatic current limit through the resistor chain and is thermally protected.
-
Product
PXI 8 Slot BRIC 40x32 1-Pole (8 sub-cards)
40-562A-121-40X32
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 12-Slot BRIC Matrix, 484x4 1-Pole (11 Sub-cards)
40-562B-321-484X4
-
The 40-562B-321-484X4 is a high density BRIC12 matrix module with a size of 484x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 2 Amp Multiplexer, Dual 16-Channel, 2-Pole
40-635A-006
-
The 40-635A-006 is a dual 16-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI 16x2 RF Matrix 300MHz 50 Multiway Connector
40-728-002
-
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXIe-8245, 4-Port, 10/100/1000BASE-T PXI Ethernet Interface Module
787313-01
-
The PXIe-8245 supports Ethernet-based communication between PXI hardware and external instruments and devices. This PXI Ethernet Interface Module includes four RJ45 10/100/1000BASE-T Ethernet interface ports in a single-slot PXI Express module.
-
Product
PXI 12-Slot BRIC Matrix, 22x16 1-Pole (2 sub-cards)
40-562B-321-22X16
-
The 40-562B-321-22X16 is a high density BRIC12 matrix module with a size of 22x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXIe-1095, 18-Slot, Up to 24 GB/s PXI Chassis
783882-01
-
PXIe, 18-Slot, Up to 24 GB/s PXI Chassis—The PXIe-1095 features a high-bandwidth backplane and 58 W of power and cooling in every slot to meet a wide range of high-performance test and measurement application needs. The chassis incorporates two hot-swappable power supplies to improve the mean time to repair (MTTR) of the PXI system; it also offers an optional timing and synchronization upgrade that includes a built-in oven-controlled crystal oscillator (OCXO) for increased clock accuracy and external clock and trigger routing. It accepts PXI Express modules in every slot and supports standard PXI hybrid-compatible modules in up to five slots.
-
Product
PXI Dual SP6T MUX 26.5GHz 50Ω SMA
40-784-032
-
Pickering Interfaces’ 40-784 PXI Microwave Multiplexer Modules have a characteristic impedance of 50 Ohm and are capable of switching signals up to 40GHz. Available in single or dual SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI 12-Slot BRIC Matrix, 264x8 1-Pole (12 sub-cards)
40-562B-321-264X8
-
The 40-562B-321-264X8 is a high density BRIC12 matrix module with a size of 264x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Single 2 Channel Fibre Optic SC/PC
40-855-212
-
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI 4 Banks of 20 Channel 1 Pole MUX
40-615-021-4/20/1
-
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
PXI 2A Multiplexer 79-Channel 2-Pole
40-611-002
-
The 40-611 Very High Density multiplexer module is available in 158-Channel 1-Pole or 79-Channel 2-Pole configurations. Both configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI Express Hybrid Peripheral Module
SMT712
-
Sundance Multiprocessor Technology Ltd.
The SMT712 is a PXI Express (opt. Hybrid) Peripheral Module (3U), which integrates two fast 12-bit DACs, 2 banks of 1GByte DDR2 memory each, a clock circuitry and a Virtex5 Xilinx FPGA, under the 3U format.
-
Product
PXI 16 x SPST Reed Relay
40-115-021
-
Available in normally open (DPST & SPST) configurations. Connections are made via a front panel micro-D 96-pin male connector. For applications requiring improved bandwidth and crosstalk performance please look at our 40-120 and 40-125 range of shielded reed relay cards. General purpose reed relays are suitable for the construction of small switching networks, slaving up to larger switches or operating external devices (e.g. lamps, solenoids etc.). To simplify inter-relay wiring, interconnection points are built onto the circuit board easing the construction of complicated wiring.
-
Product
PXI 2x SPST Power Relay, 2 Slot
40-170-001
-
Model 40-170 is available either as 2 x SPST High Power Relays, suitable for switching inductive/ capacitive loads up to 30A at 250VAC or as 2 x DPST switching up to 20A. Power Relay Modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
PXI 34x4 Signal Insertion and Monitor Matrix
40-525A-001
-
This is a PXI signal insertion and monitor matrix with switched pass thru connections on both X and Y axis. It is also availablein a 16x4 format and can be used for signal insertion and monitoring purposes on connections between the UUT and test system. Each pass thru connection from LX to X can be open or closed to allow the programmatic disconnection of the signal to check the response of the UUT. The matrix can be used to connect test equipment, such as a DMM or scope, to monitor the pass thru signals via Y connections while the LY connections can be used to insert a fault condition or insert external signals. When external signals are injected the LX connections can be opened and the LY connections closed.
-
Product
PXI-2798, 40 GHz, Dual-Transfer PXI Transfer Switch Module
782358-01
-
40 GHz, Dual-Transfer PXI Transfer Switch Module—The PXI‑2798 can route RF or microwave signals in automated test applications. Designed to operate with less than 1 dB insertion loss at up to 40 GHz, the PXI‑2798 appears almost invisible to signals at much lower frequencies as well. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2798 is also well-suited for passing high-order harmonics from RF upconverters or routing multiple sources to RF downconverters.
-
Product
Rackmount DAQ
-
A high-performance, industrial-grade measurement system designed to fit into standard 19-inch equipment racks.
-
Product
PXI Low-Leakage Switched Guard Switching Solutions
-
They are based on the switched guard design principle, and the overall designs assure isolation resistances of up to 1013Ω. This high level of isolation resistance ensures accurate and reliable measurements, making our products ideal for high-precision semiconductor testing.
-
Product
PXI BRIC8 FIBO Matrix Dual 248x4 2pin Brkout
40-592A-118
-
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines. Typical applications are in automotive and aerospace industries which involve safety or mission critical systems that have to behave predictably when cabling or sensor faults occur.
-
Product
PXIe-8842 2.6 GHz 6-Core Processor PXI Controller
787882-0118
-
The PXIe8842 is an embedded controller for PXI systems that you can use for processor-intensive modular instrumentation and data acquisition applications. The PXIe8842 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, one Thunderbolt 4 port, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, and other peripheral I/O. Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the US and/or other countries.
-
Product
PXI 2A Multiplexer, 1-Bank, 64-Channel, 2-Pole
40-614C-016
-
This 1-bank, 64-channel, 2 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI 8 Slot BRIC 150x16 2-pole (10 sub-cards)
40-561A-122-150X16
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 20Amp 28Volt 4xSPST Automotive Relay
40-180-111
-
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC.The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
PXI Prototyping Module, 2-Slot, 96-Pin Micro-D
40-225A-102
-
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI 2-Slot BRIC Matrix, 22x16 2-Pole (2 Sub-cards)
40-562B-222-22X16
-
The 40-562B-222-22X16 is a high density BRIC2 matrix module with a size of 22x16 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
