Multifunction Calibrators
An accurate temperature, pressure, frequency, voltage, current and other units of measure to facilitate their comparison to and adjustment of instruments.
-
Product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131H
Calibration Cable
The Keysight 85131H is a 62.2 cm (24.5 in) long1 flexible cable with a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss greater than or equal to 16 dB. Insertion loss is 0.25 * sqrt (f) + 0.2 dB (where f is frequency is GHz) for the test port connector, and 1.5 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 3 inch radius. Stability1 of the Keysight 85131H is less than 0.12 dB and phase is 0.13o * f + 0.5o, (where f is frequency in GHz).
-
Product
68-Pin VHCDI Male to 68-Pin VHCDI Male Shielded Cable
190233-02
Multifunction Cable
The SHC68-C68-EPM is compatible with many NI data acquisition devices. The SHC68-C68-EPM is intended for custom breakout fixtures that use the VHDCI 0.8 mm connector.
-
Product
PCI-6123, 8 AI (16-Bit, 500 kS/s/ch), 8 DIO, PCI Multifunction I/O DeviceMultifunction I/O Device
779409-01
Multifunction I/O
8 AI (16-Bit, 500 kS/s/ch), 8 DIO, PCI Multifunction I/O Device - The PCI‑6123 is a simultaneous-sampling, multifunction DAQ device. It offers analog input, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6123 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6123 dimensions require chassis slots that can accommodate full-length PCI modules.
-
Product
PXI-6120, 4 AI (16-Bit, 800 kS/s/ch), 8 DIO, PXI Multifunction I/O Module
78396-01
Multifunction I/O
4 AI (16-Bit, 800 kS/s/ch), 8 DIO, PXI Multifunction I/O Module - The PXI‑6120 is a simultaneous-sampling, multifunction data acquisition device. It offers analog input, digital I/O, two 24‑bit counters, and digital triggering. It is ideal for a variety of applications, such as stimulus/response applications for whih synchronization among analog input, analog output, and digital I/O is required; 42 V automotive applications; radar; sonar; and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
USB-7845, Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783200-02
Multifunction Reconfigurable I/O
Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7845 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7845 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
Product
Configurable 6U OpenVPX Multifunction I/O Board
Multifunction I/O
NAI offers a variety of 6U OpenVPX solutions, including rugged I/O Boards - designed to be combined with our smart function modules - to create a COTS-based, high-density, multifunction I/O solution for most sense and response requirements.
-
Product
USB-6255, 80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
779959-04
Multifunction I/O
80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB‑6255 offers analog I/O, digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Multiport Electronic Calibration Module (ECal), DC To 9 GHz, 6-ports
N7562A
Electronic Calibration Module
A series of multiport ECal that cascade-able up to 36-ports which makes it possible to calibrate a wide frequency range from DC up to 9 GHz without making numerous connections during calibration process. Ideal for multiport measurement application with VNA in such as high-volume PA/FEM, massive MIMO antenna or high-speed digital interconnect test applications
-
Product
Diagonal Measurement Kit
10768A
Mechanical Calibration Kit
The Keysight 10768A Diagonal Measurement Kit is designed for use with the Keysight 5530 Laser Calibration System. It allows linear measurements to be made on the four body diagonals of a machine tool's working volume. These measurements document the machine's capability and quickly perform a complete check of volumetric positioning performance. In addition, long-term drift tests can be performed over hours or days, showing possible effects of temperature on geometry.
-
Product
Configurable 3U OpenVPX Multifunction I/O Boards
Multifunction I/O
NAI offers a variety of 3U VPX solutions, including rugged I/O Boards and SBCs - designed to be combined with our smart function modules - to create a COTS-based, high-density, multifunction I/O solution for most sense and response requirements.
-
Product
37-Pin D-SUB Female to 37-Pin D-SUB Male Multifunction Cable
778621-01
Multifunction Cable
SH37F-37M-1 37-Pin Female to Male Shielded I/O Cable, 1 m
-
Product
PCIe-7858, Kintex-7 325T FPGA, 1 MS/s, DRAM Multifunction Reconfigurable I/O Device
786457-01
Multifunction Reconfigurable I/O
PCIe, Kintex-7 325T FPGA, 1 MS/s, DRAM Multifunction Reconfigurable I/O Device - The PCIe‑7858 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7858 features a dedicated analog-to-digital converter per channel for independent timing and triggering. This device offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
Product
3U OpenVPX Ethernet Switch and Multifunction I/O Board
68G5E
Multifunction I/O
The 68G5E is a 3U OpenVPX board that is configured with an Ethernet Switch module (choose the ES1, 12-Port GbE Cu legacy unmanaged Ethernet Switch, or the ES2 16-Port Cu GbE managed Ethernet Switch with optional 4x 10GBASE-SR 850 nm multimode Fiber Optic interface) and provides additional support for one NAI smart I/O and Communications function module. Uniquely designed, the 68G5E provides ‘independent’ Ethernet Switch capabilities and can operate as a MFIO board end point with access via the 1 x1 PCIe and/or 1x 10/100 Ethernet motherboard Control Port which hosts the NAI Ethernet Protocol Server/Listener application for direct GbE MFIO control. Ideally suited for rugged Mil-Aero applications, the 68G5E delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
RF Electronic Calibration Module (ECal), DC/300 KHz To 9 GHz, 3.5 Mm, 2 Port
85093D
Electronic Calibration Module
The Keysight 85093D RF electronic calibration (ECal) module makes the calibration of vector network analyzers fast, easy, and accurate. ECal is a precision, single-connection calibration technique for your vector network analyzer. Performing a full two-port calibration takes less than half the time and a number of connections using ECal versus mechanical calibration kits. Furthermore, the accuracy of the calibration is comparable between electronic and mechanical methods. Traditional mechanical calibrations require intensive operator interaction, which is prone to errors. With ECal, the operator simply connects the ECal module to the network analyzer and the software controls the rest.
-
Product
PXIe-6124, 4 AI (16-Bit, 4 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module
780536-01
Multifunction I/O
PXIe, 4 AI (16-Bit, 4 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXIe‑6124 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 32‑bit counters, and analog and digital triggering. The PXIe‑6124 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCIe I/O & Comm Board
79C3
Multifunction I/O
NAI’s 79C3 is a PCIe Multifunction I/O and Communication Board with three independent function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
Multifunction Switch / Measure Unit, Modules
34980A
Multifunction Switch/Measure Unit
The 34980A General Purpose switches can be used to route signals or to control other devices in an application. These switches are ideal for device actuation, switching loads or power supplies. Both switches offer high power channels up to 150W. The general purpose modules also include a relay switch counter to help predict when relays need to be replaced.
-
Product
68-Pin SCSI Type Male to 68-Pin VHDCI Male, Twisted Pair, Shielded Multifunction Cable
192288-0R3
Multifunction Cable
SH68M-68M-EPM, Male 68 pin SCSI to 68 pin VHDCI, 0.3m
-
Product
PCI-6143, 8 AI (16-Bit, 250 kS/s/ch), 8 DIO, PCI Multifunction I/O Device
778913-01
Multifunction I/O
The PCI‑6143 is a simultaneous-sampling, multifunction DAQ device. It offers analog input, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6143 is ideal for a variety of applications, such as … high-energy physics, ultrasonic and sonar testing, ballistics and highly transient signals, and multiaxis control. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCIe-7846, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
786456-01
Multifunction Reconfigurable I/O
PCIe, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The PCIe-7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe-7846 features a dedicated analog-to-digital converter per channel for independent timing and triggering. This device offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
Product
Economy Mechanical Calibration Kit, DC To 6 GHz, Type-N, 50 Ohm
85032E
Mechanical Calibration Kit
The Keysight 85032E economy calibration kit contains a type-N male fixed termination and a one-piece type-N male open/short circuit. These standards are used to calibrate Keysight network analyzers for measurement of devices with 50 ohm type-N connectors. The kit is specified from dc to 6 GHz.
-
Product
68-Pin D-SUB Female to 68-Pin D-SUB Female, Twisted Pair, Shielded Multifunction Cable
199006-0R25
Multifunction Cable
SH68-68-EPM Shielded Cable, 68 D-Type to 68 D-Type, 0.25m
-
Product
68-Pin VHDCI Male to 68-Pin SCSI Female Analog Cable
157599-01
Multifunction Cable
SHC68-68-A2, 68-Pin Male VHDCI to 68-Pin Female SCSI, 1m Cable
-
Product
3U cPCI I/O & Comm Board
75C3
Multifunction I/O
NAI’s 75C3 is a 3U cPCI multifunction I/O and communication board with three independent function module slots. Two of the slots can be configured with a variety of I/O and communication functions; the third, with either a combination module featuring four multiplexed A/D channels and 28 Discrete I/O programmable channels, or with a reference supply. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
3U OpenVPX Multifunction I/O Board
68C3
Multifunction I/O
NAI’s 68C3 is a 3U OpenVPX multifunction I/O and communication board with three function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
PXIe-6386, 8 AI (16-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module
785926-01
Multifunction I/O
PXIe, 8 AI (16-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module - The PXIe-6386 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe-6386 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
68-Pin SCSI Female to 68-Pin Right-Angle SCSI Female, 1 m, Twisted Pair, Shielded Multifunction Cable
187051-01
Multifunction Cable
SH68-68R1-EP, Shielded Cable, Right Angle Connector, 1 m
-
Product
PXI-7851, Virtex-5 LX30 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module
780339-01
Multifunction Reconfigurable I/O
Virtex-5 LX30 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7851 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7851 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
Product
PXIe-7858, Kintex-7 325T FPGA, 1 MS/s, DRAM PXI Multifunction Reconfigurable I/O Module
784147-01
Multifunction Reconfigurable I/O
Kintex-7 325T FPGA, 1 MS/s, DRAM PXI Multifunction Reconfigurable I/O Module—The PXIe‑7858 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe‑7858 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe‑7856 also includes peer‑to‑peer streaming for direct data transfer to other PXI Express modules.
-
Product
PXI-6232, 16 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sourcing DO, Bank-Isolated, PXI Multifunction I/O Module
779618-01
Multifunction I/O
16 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sourcing DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6232 is a bank-isolated DAQ device designed for voltage I/O. It offers analog I/O, digital input, sourcing digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 24 V signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6232 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6232 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
