Burn-In
The application of current, typically at high temperatures, over periods of time to detect infant mortality.
See Also: Burn-In Boards, High Power Burn-in, Burn-In Sockets, PCB Inspection
-
product
Burn in Tester
Evolusys Technologies Sdn. Bhd.
• Measures 32 leds’ voltages individually, sequentially, continuously in LIFE FEED mode• Over-current and over-temperature shutdown for individual LED• Detect short and Open circuit for each LED location in Live Feed• Monitoring Time: 300ms (32 channel)• Tolerance : +/- 0.005V
-
product
Burn-in Systems
Incal Offers A Line Of State-Of-The-Art Burn-In Testing Hardware And Software For Retrofit And/Or Total, Customized Burn-In System Configurations.
-
-
product
Burn-In Test
Trio-Tech provides a comprehensive range of semiconductor testing services through its state-of-the-art laboratories in the Far East. The laboratories provides static and dynamic Burn-in /HTOL /SLT testing and other testing services. All of the company’s testing facilities are ISO9001, ISO14000, ISO17025 and DSCC certified ensuring that operating policies and procedures meet stringent international standards for consistency and reliability.
-
product
Multiple Channel Burn In Power Supply
MCPS
The most important features of this burn in power supply is its ability to hold a constant output for each channel even in the event that a unit under test on one channel may short and fail. Since each channel has it''s own transformer, no glitches or voltage spikes can get into any of the other channels. This image shows the results as the second channel from the left is shorted with a small wire and the circuit breaker pops out. Used for burn-in testing and other timed testing where power isolation is required. Very basic simple circuit, see schematic below. Cleans and frees up benchtops, burn in racks and work space clutter. Available in benchtop or rackmount.
-
product
Burn-In Test
C.C.P. Contact Probes Co., LTD.
Customized Burn-In Test Sockets for temperatures of up to 180°C.
-
product
Burn-In Test Sockets
The selection of the test socket is critical to the performance of a device during qualification testing where electrical bias and signals are applied. Key factors such as mechanical compatibility, operating temperature, ability to withstand high moisture levels, signal speed and lead inductance/capacitance all need to be taken into account when selecting the best socket for the test application.
-
product
Production Wafer Level Burn-in
TV19 VersaTile™ probe cards are designed with Celadon’s patented ceramic technology for superior electrical performance, yet is highly modular due to it’s 28mm x 28mm chassis. Micro-adjustments can be made in seconds with an allen wrench and a microscope. Easily align VersaTile cards for different wafer layouts using a 4.5” compatible 1×3 , 200mm, or 300mm VersAdjust plate.
-
product
Environment And Burn-in Temperature Chambers
9000 Series
Delta 9000 Series Temperature Chambers offer a wide choice of temperature ranges and capacities in addition to smart electronics. Field proven by satisfied customers for over four decades, Delta chambers are quality instruments that provide service longevity and integrity unique in their field. Over the years, Cohu has added advanced features to the proven basic chamber design and has refined system components and programming capability to deliver outstanding quality and value.
-
product
Test & Burn-In Socket for Devices up to 13mm Square
CSP/MicroBGA
Test & Burn-In Socket. Socket is easily mounted and removed to & from the BIB due to solderless pressure mount compression spring probes which, are accurately located by two molded plastic alignment pins and mounted with four stainless steel screws. Standard molded socket format can accommodate any device package of 13mm or smaller, by using machined (for small quantities) or custom molded (for large quantities) pressure pads and interposers.
-
product
Burn-in Room and Aging Test Chamber
Isolated type of burn-in room features: ●Separate the product and loading area, easy to control temperature and maintain. ●Temp. range: 40-70ºC±3/±5ºC, ●Temp. constancy: ±0.5ºC ●Uniformity: ±3ºC ●Test frame materials: painted stainless steel or a combination of forming aluminum ●Insulation: with PU foam ( doors with double glazing ) insulation, so that the internal temperature is not subject to external factors, to achieve power saving effect ●Product hierarchy placement, Selection of layer height in accordance with the requirements, convenient access ●Computer monitoring system is optional. ●Noise level:≤75dB Application Suitable for all kinds of electronic products, especially for products with heating characteristics Product and loading area should be separated Large-scale production
-
product
Burn-in System
Sonoma
High power burn-in system with advanced testing functionality at DUT level for substantially lower cost and high performance using State-of-the-Art technology
-
product
Burn-in and Stress Screening Chambers
KDR
Supervise the operation of your product, electronic device, circuit board, or medical device while they are stress screened, burned-in, or temperature cycled inside a Bemco Kardburn or Koldburn glass front chamber. With a huge amount of testing or storage space within instant reach, KD Chambers provide a compact and attractive alternative to a walk-in chamber.
-
product
Memory Burn-In Test
The N3500 is Neosem Technology’s fourth generation memory test system. Specifically designed for Flash Components and Flash Cards, the N3500 tester-on-a-board architecture targets the broadest range of DUT technologies in various form factors and packages. Each Tester Board (or “Blade”) contains 288 I/O pins and 32 DPS supplies.
-
product
Burn-In Test Fixtures
Burn-in generally involves the extended operation of a product in a temperature-controlled environment. With possible humidity and supply voltage margining - the burn-in process can then be extended to include power stress (levels and on/off cycles) tests, high humidity environmental simulation as well as the classic "four corner test" of high voltage + high temperature, high voltage + low temperature, low voltage + high temperature and low voltage + low temperature.
-
product
Burn-In Board Tester
Focus-275
Focus275 is a tester for burn-in board.It can improve reliability of burn-in board by inspecting boards for burn-in test by Focus275 regularlyBoth short open test and component test can be done by sending electric signals for special socket contactor and edge part.
-
product
Burn-in or Rapid Temperature Cycling Chamber
KDL Series
The Bemco KDL series is designed for production testing of electronic circuit boards and completed electronic systems. They accept Bemco KDLC Carts that have a working area of 42 wide by 60 high by 48 deep suspended on insulated runners and casters 11 inches above the test area floor.
-
product
Laser Diode Burn-in Reliability Test System
58604
The Chroma 58604 is a high density, multi-function, and temperature controlled module for laser diode burn-in and lifetime tests. Each module has up to 256 SMU channels which can source current and measure voltage in various control modes as described below.
-
product
300mm Single Touchdown Burn-in and Test System
FOX-15
Up to 15 wafers at a time Known Good Die solution Lowers production cost
-
product
Photodiode Burn-in Reliability Test System
58606
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
product
Blanket Flammability Tester
TF316
TESTEX Testing Equipment Systems Ltd.
Blanket Flammability Tester, to determine the ignition resistance property of blanket fabrics and surface flame spread performance of fabric. A standardized flame is applied to the surface of specimen for a special time under controlled conditions, and burning, changing, or discoloration of a paper monitor is noted to classify flammability of tested fabric.
-
product
Package Level Test
Applicable for burn-in, reliability andlife testingACC and APC control modesIndividual channel driving and measurementDriving current 500mA per channel
-
product
Wireless Digital Multimeter 4000 count / NCV / SPT / Anti Burn Protection and with Max./Min./Max.-Min. display
MS-W2044P2
This is a external wireless connectivity Digital Multimeter integrated with 4000 Count, True RMS auto and manual measurement.
-
product
BIB Loading
FALCON Series
The Falcon Series is an automated BIB loading and unloading machine. It is designed to provide precise high-speed loading of DUTs from Trays/Tube to Burn-in boards and precise high-speed unloading of DUTs from Burn-in boards to Trays/Tube for different device packages. The Falcon Series also has a simple conversion kit which allows end-users to re-configure the equipment for different types of sockets and package combinations.
-
product
Custom PCB Test Fixtures
Emergent Electro-Mechanical designs and manufactures customized test fixtures and burn-in racks. Each of our custom designs is unique to our customer's particular project requirements. Emergent fixtures feature innovative design components including a linear collapsing system, interchangeable and reusable plate design, and top and bottom probing.
-
product
Semiconductor
With ultra-multi pin count and fine pitch, our general-purpose IC socket lineup corresponds to every need. For semiconductor burn-in sockets for thermal acceleration tests, and test sockets for semiconductor electrical testing, we continue to hold a high market share all over the world.
-
product
Medical Storage Chambers
KDM
The Bemco KDM is similar to the Bemco Koldburn KDR except it has a circular air flow conditioning system located on the chamber ceiling, and is optimized for shelf supported temperature cycling, burn-in, stress screening, and storage of valuable pharmaceutical products or medical devices.
-
product
Burn Down Transformer
ATG 6000
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR ATG 6000. The high performance ATG 6000 burn down transformer is used for impedance reduction of cable faults in low- and medium-voltage networks. The short-circuit proof 5.75 kVA stray field transformer delivers a maximum voltage of 15 kV and is housed in a fully enclosed 19" housing.* Proven methodes for cable faults that are difficult to locate* Useful for cables that are difficult to access* Robust construction for reliable functions* Independent current and voltage control on each burning level
-
product
Flame Burning Tester
DRK3024A
Shandong Drick Instruments Co., Ltd.
It is used to detect high temperature resistance, combustibility and combustion performance of materials.
-
product
High Voltage Switching Test System
The advanced development of new technologies, such as SiC and GaN, have opened the opportunity for more efficient and higher voltage/power performance in switching and power management circuits. Their high cutoff frequencies, low on-state resistance, and very high breakdown voltages can increase power supply power handling densities approaching hundreds of watts/inch. Reliability of these new technologies and techniques is critical for realizing practical applications. While Silicon devices have a rich history of proven reliability, these newer compound semiconductor technologies are too new to have a reliability history and have not been well proven. Further, process variations, even in well-controlled lines, yield widely varying results. This has driven the need for additional testing and to burn-in devices prior to delivery.
