Pulse Code Modulation
standard digital way to represent audio.
-
Product
PXI 2 Amp Multiplexer, Quad 8-Channel, 2-Pole
40-635A-009
Multiplexer Module
The 40-635A-009 is a quad 8-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI 4 Slot BRIC 276x8 1-Pole (6 sub-cards)
40-560A-021-276X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI BRIC8 FIBO Matrix Dual 30x2 3pin brkout
40-595A-005
Matrix Switch Module
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
-
Product
PXI Load Resistor Module 40 Ohm to 295 Ohm
40-292-011
Load Resistor Module
The 40-292 module is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors. The short circuit position is fully thermally protected and provides a short circuit current limit. The series open switch provides an automatic current limit through the resistor chain and is thermally protected.
-
Product
PXI High Density Precision Resistor Module, 4-Channel, 2.5Ω to 6.97kΩ
40-298-124
Programmable Resistor Modules
The 40-298-124 is a high density programmable resistor module with 4 channels which can be set between 2.5Ω and 6.97kΩ with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 4 Slot BRIC 75x16 1-Pole (5 sub-cards)
40-561A-021-75X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI/PXIe 15W Programmable Resistor Module
40-254-015
Programmable Resistor Modules
The 40-254-015 (PXI) and 42-254-015 (PXIe) are programmable resistor modules with 2 channels which can be set between 1Ω and 920Ω with 4Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PXI/PXIe RF Matrix, 16x4, 100 MHz, 75 Ω SMB With Loop-thru
40-727A-101-L
Matrix Switch Module
The 40-727A-101-L (PXI) and 42-727A-101-L (PXIe) are 16x4 75 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
PXI 8-slot BRIC Power Multiplexer, 2-Channel, 24-Pole (3 Sub-cards)
40-571A-101
Multiplexer Module
The 40-571A-101 is a 2-channel, 24-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
Product
PXI 8 Slot BRIC Matrix, Solid State, 320x8, 1-Pole (10 sub-cards)
40-563B-121-320X8
Matrix Switch Module
The 40-563B-121-320x8 is an ultra high density 8-slot matrix module with 1-pole switching and is part of our range PXI BRIC matrices. They are available in 2, 4 or 8-slot sizes to suit high performance PXI switching requirements and are constructed using solid state switches.
-
Product
PXI MUX 4 Banks of 16 Channel 2 Pole
40-610-022-4/16/2
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
LXI 16x8, 10A, 1-pole Matrix
60-600-006
Matrix Switch Module
A high power single pole matrix module capable of switching up to 400VDC/250VAC, 10A (300W/2500VA max power)
-
Product
PXI Single 64x4 Matrix 1-Pole Switching
40-533A-021
Matrix Switch Module
Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109 operations to give maximum switching confidence with long life and stable contact resistance.
-
Product
LXI Microwave Multiplexer, SP4T, 7-Bank, 67GHz, 50Ω, SMA-1.85
60-803-807
Multiplexer Module
Our 60-803-807 is a 7 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
6GE Port Gigabit Unmanaged Industrial PoE Ethernet Switch
EKI-2706G-2GPI
Ethernet Switch Module
6 Gigabit RJ-45 Ethernet ports. Support 4 x IEEE 802.3at/af PoE ports for PD demands, Up to 30W output per PoE port. Supports jumbo frame transmission up to 9k bytes, 12 ~ 48 VDC redundant dual power input and 1 relay output, Wide operating temperature range of -40 ~ 75°C.
-
Product
High-Density 128-CH Isolated DIO/DI/DO PCI Cards
PCI-7442/7443/7444
Analog Input Module
Responding to the industry"s need for high-density digital input/output modules, the ADLINK PCI-7442/7443/7444 DIO card series delivers up to 128 opto-isolated channels for a wide range of demanding PCI-based applications. The PCI-7442/7443/7444 series comes with 64 (PCI-7442) or 128 (PCI-7443) opto-isolated digital inputs and 64 (PCI-7442) or 128 (PCI-7444) opto-isolated digital outputs. With a 1250 VRMS (excluding cables) channel-to-system isolation protection, these cards are shielded from damage caused by accidental contact with external voltage while promoting simple ground connections. All input channels are identical non-polarity with each line isolated and suited to collect digital inputs even at high-noise environments. Featuring a Change-of-State (COS) interrupt function, the PCI-7442/PCI-7443 instantly generates an interrupt request to the PCI controller when it detects a sharp change in the logical state of any of its digital inputs.
-
Product
PXI 2 Amp MUX, Single 8-Channel 8-Pole
40-635-004
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
32-CH Sinking Type Digital Ouput EtherCAT Module
EPS-2132
Digital Output Module
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
PXI 3A Power MUX BRIC, 9-Channel, 16-Pole
40-571-203
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXI/PXIe High Voltage Multiplexer, Dual 4-Channel, 1-Pole
42-321-100-HI
Multiplexer Module
The 40-321-100-HI (PXI) and 42-321-100-HI (PXIe) are dual 4-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-134-HI
Programmable Resistor Module
The 40-230-134-HI (PXI) and 42-230-134-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 102kΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Load Module for SLSC
Load Module
Bloomy's 8-Channel Load Module provides isolated current and voltage measurements for eight on-board 5W loads or for eight off-board 120W loads. With built-in switching for calibration and fault injection, the module provides unsurpassed capability for Mil/Aero applications. The module also provides switching and connections to allow switching between a real load (e.g., actuator, valve, etc.) and the simulated load.
-
Product
PXI 4x3 10GHz Matrix with Loop-Thru & Term
40-787-518-4X3-L-T
Matrix Switch Module
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 3-Bank 18GHz SMA
60-802-203
Multiplexer Module
The 60-802-203 is a 4-channel, 3-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI/PXIe MEMS Optical Switch, Single Insert/Bypass
40-860A-112
Multiplexer Module
The 40/42-860A-112 is a PXI/PXIe single insert/bypass switch with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Single 16-Channel, 2-Pole
42-739-001
Multiplexer Module
The modules are ideal for the testing of multiple devices that use a serial communication interface, allowing the test system to select one target device from many. The design is bi-directional to permit use as a multiplexer or de-multiplexer with no impact on performance. The module uses long lifetime electromechanical relays characterized for use in communications systems.
-
Product
MXM GPU Expansion Module
MIC-75GF10
Expansion Module
Support NVIDIA MXM GPU with whole system fanless designSupport up to 80W NVIDIA Quadro MXM 3.1 Type A/B form factor GPU1 x HDMI and 3 x DisplayPort 1.4a display outputOperating Temp. -10~50CSupport 1Grms Op. vibrationDual front removable 2.5" storage bay for easy swapIP40 fanless ruggedized compact size designMIC-7 Series compatible
-
Product
PXI 10W Programmable Resistor Module, 1-Channel, 2Ω to 13.6kΩ
40-253-031
Programmable Resistor Modules
The 40-253-031 is a programmable resistor module with 1 channel which can be set between 2Ω and 13.6kΩ with 0.25Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 2A Multiplexer, 158-Channel, 1-Pole
40-611A-001
Multiplexer Module
The 40-611A-001 158-Channel, 1-Pole MUX is part of our range of Very High Density 2 Amp multiplexer modules. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber, LC Connectors
42-850A-414-M50
Multiplexer Module
The 40/42-850A-414-M50 is a PXI/PXIe 4-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
