Signaling
The use of signals for controlling communications. (atis.org)
See Also: Signal, Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
product
Amplifiers
Alnair Laboratories Corporation
A specially designed Erbium-doped fiber amplifier which offers a superior optical amplication performance with a very high gain factor and a minimal added noise. A near quantum limited noise figure of typically 3.8dB, and a small-signal optical gain of over 50dB is achievable with input signal as low as -50 dBm reflecting the impact of the specialty fiber and composite amplifier design, making it an indispensable amplifier for weak optical signals.
-
product
Multiple-Input Multiple-Output (MIMO) Sine Test
EDM Modal Sine Testing includes a dedicated test setup and operation process flow using a single or multiple modal shakers outputting a sine wave to acquire FRF signals. The Source Output type is either Swept sine or Stepped sine. The sweep mode can be linear or logarithmic.
-
product
Peak Power Measurement
Directly measure the instantaneous peak power level of a pulse modulated signal. Use the "sample delay" function to set the desired measurement point on the waveform. And an external scope can be used to view the profile and see the exact measurement point on the pulse.
-
product
PXI 2 Amp Multiplexer, 4-Bank, 16-Channel, 1-Pole
40-657A-001-4/16/1
The 40-657A-001-4/16/1 is a 4-bank, 16-channel, 1-pole MUX and is part of our range of High Density 2 Amp Power Multiplexer Modules available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
product
PXI RF Multiplexer Switch Module
PXI RF Multiplexer Switch Modules are ideal for high-channel-count applications that need to connect measurement or signal generation instruments to various test points on devices or units under test(DUTs or UUTs). PXI RF Multiplexer Switch Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor(FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a multiplexer that fits your requirements. To program the switches, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control of switches. For intelligent management of complex switch systems, NISwitch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
product
High Performance Intel Mission Computer
ComSys-5363
The ComSys-5362 is a rugged COTS mission computer. A server grade Intel Core™ i7-7820EQ Xeon E3 CPU supports signal processing for critical applications. Highly configurable, application-specific I/O. Removable drive bay for two 2.5“ SSDs.
-
product
signal analyzer
DSA DOCSIS
Only the highest signal quality ensures maximum throughput. The R&S®DSA DOCSIS signal analyzer has been designed to support users by ensuring the highest signal quality. DOCSIS is the standard for transmitting IP data within hybrid fiber coaxial (HFC) cable TV networks.
-
product
PCI-5152, 300 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device
779945-03
300 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device—The PCI‑5152 high-speed oscilloscope device has two channels that sample up to 2 GS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 300 MHz of analog bandwidth and flexible measurement configurations.
-
product
Booster and In-line Amplifier
Amonics' EDFA range adopts unique design to produce maximum signal gain and saturated output power while maintaining low noise figure, enabling test capabilities in system or component level manufacturing and characterizing processes, as well as facilitating highly demanding R&D applications. The compact turnkey benchtop or 19" rackmount unit incorporates a user-friendly front panel housing with a LCD monitor display, key switch, power control knob and optical connectors. An integrated RS232 computer interface enables easy control, diagnostic functions and data acquisition.
-
product
GPS, GLONASS, Galileo Micro Splitter 2 Way, SMA, 1176.45 - 1602.00 MHz, 50 Ohm, Passive
GPSL15
INSTOCK Wireless Components, Inc
GPSL15 is a two way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while providing a DC current path to power a remotely located active GPS antenna from one receiver while blocking the DC path from the other. Max voltage rating at the DC blocked port is 10 VDC; maximum current rating is 50 mA. Maximum voltage rating at the DC pass port is 50 VDC; max current rating is 1000 mA. Furnished with SMA female connectors all ports. Being a "micro-sized" splitter, GPSL10 weighs only 21 grams and is suitable for applications requiring low-weight parts.
-
product
6GHz Dual Channel Signal Generator
LS6082B
The LS6082B is a 6GHz Dual Channel RF Analog Signal Generator, offers industry leading performance, in an easy to use benchtop box. It features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The design offers excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
product
AC Coupled, 14-Bit Digitizer For ExpressCard 54, 2 Channels 150 MS/s
EC14150A
The EC14150A (EC) is an AC-coupled dual channel waveform capture board that provides a remarkable combination of high speed and high resolution sampling along with a very large memory capacity all in a very compact and low power consuming ExpressCard form factor. At 4.5 W, the EC represents one of the lowest power consuming digitizer cards ever created for its class. Signal frequencies up to 200 MHz can be accurately captured either in baseband or in higher order Nyquist zones using under-sampling techniques. Where DC-coupling is required, the EC14150D should be considered.
-
product
LilyPad Temperature Sensor
Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to digital conversion on the signal line will allow you to establish the local ambient temperature. Detect physical touch based on body heat and ambient conditions with this small sensor.
-
product
Oscilloscope: 200 MHz, 4 Analog Channels
DSOX2024A
200 MHz4 analog channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add digital channels, 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
product
NI-9213, cDAQ-9171, and cRIO-9940 USB Temperature Measurement Bundle
865682-01
NI-9213, cDAQ-9171, and cRIO-9940 USB Temperature Measurement Bundle - The USB Temperature Measurement Bundle with NI-9213, cDAQ-9171, and cRIO-9940 includes the NI-9213 C Series Temperature Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the cRIO-9940 Backshell for strain relief and operator protection from high-voltage signals. The included NI-9213 provides noise immunity, a high common-mode voltage range, NIST-traceable calibration, differential analog inputs, and four channels. Additionally, the NI-9213 features anti-aliasing filters, open-thermocouple detection, and cold-junction compensation for high-accuracy thermocouple measurements.
-
product
Signal Conditioners
Process transmitters isolate, filter amplify, and convert sensor signals to 4-20mA current or 0-10V voltage signals for interfacing with controllers and other instrumentation. Select from 2-wire loop-powered 4-20mA transmitters, 3-wire DC-powered transmitters, or 4-wire AC/DC-powered transmitters. 3-wire and 4-wire models are available as 4-20mA transmitters or voltage transmitters. DIN-rail and field-mount version are available. Configuration is easy with Windows software, push-buttons, switches, or pots for span/zero settings depending on the series.
-
product
PXI MUX 2 Bank, 32 Channel Screened 1 Pole
40-610-021-S-2/32/1
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
product
10 MHz to 55 GHz Noise Sources
CNS346 Series
The Spanawave CNS346 Series is designed for precision noise figure measurement applications. The superior VSWR characteristics reduce multiple reflections of the test signals and significantly increase the measurement accuracy of most noise figure set-ups. The CNS346 Series noise sources have broadband coverage and extremely good temperature and voltage stability, for the finest noise figure meter-compatible laboratory standards. Outputs of 6, 15.5 and 22 dB ENR are available, allowing the units to accurately measure noise figures up to 20 ,30 and 36 dB respectively.
-
product
PXI 8/16-Channel Isolated D/A Converter
M9185A
The M9185A is a fully independent, isolated D/A converter that is capable of supplying high voltage levels in parallel of up to eight or sixteen channels. Each channel is able to output up to 16V as stimulus signals to Device Under Tests (DUTs).
-
product
TV Analyzer
ETL
The R&S®ETL TV Analyzer is an all-in-one solution. It combines the functionality of a TV and FM (radio) signal analyzer, a video and MPEG TS analyzer and a spectrum analyzer in a single instrument. The R&S®ETL also contains generators to create analog video signals, audio signals and MPEG-2 transport streams.
-
product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
product
Digital Digitizer
MOS2
Mezzanine module (mezzanine) MOS2 is designed to convert instantaneous voltage values of an electrical signal into a digital code, measure instantaneous voltage values. The mezzanine is intended for use in HF and microwave systems as a terminal device for digitizing intermediate frequency signals up to 200 MHz. Together with the frequency converter DOWNCONVERTER 10 GHz LXI manufactured by the holding "Informtest" MOS2 under the control of the common software shell ACM2 makes up a synthetic instrument - spectrum analyzer, a ready-made solution for testing microwave devices and radio reception channels.
-
product
8K Super Hi-Vision Video Pattern Generator
Model 2238
Featured in modular design, the 2238 Video Pattern Generator is capable of providing 8K Super Hi-Vision (7680 x 4320 / 8192 x 4320) resolution for testing. Full 8K at 30/60 Hz resolution is supported by one single module (via a HDMI Display Port), and up to 4 modules can be installed and configured as required for all testing application to 8K. DisplayPort 1.3 signal module (Optional)
-
product
Cloud-Based RF Signal Analysis Software
Cloud4Testing
Our next-generation software as a service (SaaS) platform is an ideal choice for your test and measurement needs. With the R&S®Cloud4Testing, you can enjoy a quick and easy access to Rohde & Schwarz testing essentials without having to make a big investment. Simply measure, analyze and process your individual RF data, on demand and on the go.
-
product
Power Sensors
RTP5006
Providing the highest video bandwidth and fastest rise times, the 50 MHz to 6 GHz Power Sensor by Boonton is the ideal instrument for fast, accurate and reliable RF power measurements.This module is ideal for many different applications including Crest Factor and Peak to Average Power Ratio (PAPR) measurements for Power Amplifiers and RF components; Telecommunication & Satellite signals: W-CDMA, QAM, OFDM, LTE-FDD and LTE-TDD; WiFi signals: 802.11ac and legacy 802.11 a/g/n/b; RF and Microwave pulse modulated power measurements: RADAR, MRI, Particle Accelerators; General purpose scalar measurements such as gain and return loss using modulated and pulsed signals as well as CW; and Monitoring, Recording, ALC loops, transient phenomena.
-
product
LXI Microwave Multiplexer, SP4T, 6-Bank, 26.5GHz, 50Ω, SMA
60-803-306
Our 60-803-306 is a 6 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
RF Downconverters
Today’s high-band signal standards are using higher frequencies and wider bandwidths than ever before for applications such as next generation 5G wireless services, satellite communications, electronic warfare, and more.
-
product
LXI Dual 8:1 Optic MUX FC/APC Loop-Thru
60-850-022
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
product
WDM Optical Network
In fiber-optic communications, wavelength-division multiplexing is a technology which multiplexes a number of optical carrier signals onto a single optical fiber by using different wavelengths of laser light.
-
product
14-Slot Combination PXIe Chassis
GX7100e Series
The GX7100e Series are 14-slot combination PXIe chassis that accommodate a 3U PXIe embedded controller or a MXI express controller as well as 3U & 6U PXI / PXIe insruments in 4U of rack space. The GX7100e’s unique format includes seven 6U slots and seven 3U slots arranged horizontally to reduce the overall size of the chassis, providing the versatility and high-density necessary to address many PXI / PXIe applications and requirements. The backplane architecture supports Gen 2, 4x4 PCI Express bus signaling and the use of both x1 or x4 system controllers. By offering a combination of PXI-1, Hybrid, and Express slots, the GX7100e offers users the ultimate in flexibility for general purpose as well as high bandwidth test needs.
