Level
high or low along a bead it's a measure referenced.
See Also: Liquid Level, Signal Level Meters, Level Transmitters, Depot Level Test
-
product
Charge Plate Monitor
The electrostatic resistance of electronic devices is declining, and the number of ionizers installed is increasing. Ionizers cause deterioration of static elimination performance and imbalance of ions due to dirt and wear of the discharge electrode needle. Charging of electronic devices is also caused by ion blow. of an ionizer that is out of balance due to dirt and wear, and reaches a level that destroys advanced electronic devices.The atmospheric ion monitor measures the potential of the charging plate (detector), which has almost the same capacitance as the device's ground capacitance , with high accuracy, and is the most suitable measuring instrument for checking the effect when installing the ionizer and for daily management.
-
product
Vibration Meters
Companies must comply with the Control of Vibration at Work Regulations 2005 – this requires them to minimise and monitor exposure to hand-arm vibration and make sure that it does not exceed set levels and cause Hand Arm Vibration Syndrome. The best way to do this is by using a hand-arm vibration meter.
-
product
PXI Switched Guard Reed Relay Module, 13x SPST
40-121-002
The 40-121-002 provides 13x SPST switches in a single slot PXI module and designed to provide an isolation resistance in excess of 1013Ω. It has been designed to ensure high isolation resistance through the use of switched guards, making it ideal for low level measurements and semiconductor test.
-
product
SparkFun Environmental Combo Breakout
CCS811/BME280 (Qwiic)
The SparkFun CCS811/BME280 Environmental Combo Breakout takes care of all your atmospheric-quality sensing needs with the popular CCS811 and BME280 ICs. This unique breakout provides a variety of environmental data, including barometric pressure, humidity, temperature, TVOCs and equivalent CO2 (or eCO2) levels. To make it even easier to use this breakout, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1" spaced pins in case you prefer to use a breadboard.
-
product
Multiple Module Serial Bus Test Instrument
Bi4-Series
The wide variety of serial buses used in defense and aerospace applications typically requires multiple single-purpose instruments. Too often, they are difficult to reconfigure in order to test a different application.The Bi4-Series provides all the capabilities needed for complete communications bus access test for up to four serial buses used in board level (SRA/SRU) and box level (WRA/LRU) equipment—all in a single VXI module.The instrument includes test applications, industry-compliant software drivers and hardware enabling straightforward integration into automatic test systems.With the configuration flexibility needed to effectively test every bus format used in defense and aerospace applications, the Bi4-Series instrument plays a key role in reducing implementation time and test system cost.
-
product
Secondary Master Oscillator
VCH-002
The secondary master oscillator (VZG) is designed to operate in a digital communication network as a synchronization equipment of the second level of the hierarchy. Its task is to track in phase one or more clock signals coming through the network from the synchronization equipment of the highest or equivalent level of the hierarchy.
-
product
Commercial Grade Image Intensifier Tubes
ECHO Series
The commercial grade image intensifier tubes are used to amplify low light level images in a wide light spectrum for civil applications.Discover ECHO the high performance commercial image intensifier by Photonis. The ECHO technology is the commercial grade image intensififier tube by Photonis, offering two high performance grades to the commercial market for civilian users.ECHO image intensifier tubes serve many night vision applications for users that require good range and details at night andmaking them perfect for sport shooters, hunters, airsoft practioners and night vision enthusiasts.
-
product
Magnetic Stripe Test Cards
Test Limit Cards (and tickets) are nominally encoded to ISO standards BUT WITH specific parameters deliberately set to predetermined levels, which can be inside or outside the ISO limits. The Test Limit Cards are designed for use by Test\Inspection Departments, Field Service Engineers, Reader \ Encoder Development Engineers to check and confirm proper operation of magnetic stripe reading equipment (e.g. ATMs and POS).
-
product
36.6" 1920 X 290 Onboard Passenger Information Display System
ARD-RS3660
- EN50155 compliant for railway with cabin temperature OT1 level / EN45545- Brightness: 700 nits- NXP i.MX8M Plus / Intel Atom x7433RE Processor- Supports 2x M12 D-code LAN 10/100Mb- Wide range DC 24-110V power input- Auto-dimming for enhancing readability and eco-friendliness- IK grade glass/Anti-glare/Anti-reflection/SRF surface coating (optional)- ADLINK PIDS software with EGiFlow for on-site configurations (optional)
-
product
Static Charge Checker
STME-STATCHK
Statclean Technology (S) Pte Ltd
This is an ideal training kit for verifying and demonstrating the level of static charges generated by persons in an ESD sensitive area.It also demonstrates the effectiveness of eliminating static charges when a person is properly gounded by a wrist strap.NOTE: Product comes with 9V alkaline battery and a carrying case
-
product
Interferometer
S100|HR
CNC polishing puts new demands on metrology tools. Many of these optics are aspheric with tight tolerances. The new machines can produce almost any surface and require a new level of metrology to provide feedback to the polishing process. This just cannot be done with outdated interferometers designed over 30 years ago. The S100|HR has the performance it takes, without breaking the bank. Measure 10X higher fringe densities to enable final figuring to begin sooner, saving you time and money. Plus measure these high density fringes 5X more accurately to enable large polishing corrections that converge quickly to final figure, including aspheres.
-
product
Air Data Computer (ADC) Tester
MS 1122
The ADC tester is used in 2nd line maintenance is to check the functionality of ADC. This unit is a rugged customized hardware based on full functionality test of ADC. The Air Data Computer (ADC) Tester is a fully automated GO/NOGO tester with full functional testing in 2nd line maintenance. This tester is to test ADC at unit level and identify faulty Shop Replaceable Unit (SRU). This tester is also used to carry out PI checks on ADC before clear them for installation on aircraft. ADC Interface board designed to test full functionality of ADC. The Air Data Computer (ADC) test equipment shall be used for testing ADC of Tejas Aircraft. ADC test equipment shall verify the functionality against specifications during second line maintenance and pre-installation on the aircraft.
-
product
Single 8 To 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-763A-001
The 40-763A-001 terminated single 8 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
product
PXI 8 Slot BRIC 30x16 1-Pole (2 sub-cards)
40-561A-121-30X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 4 Slot BRIC 60x16 1-Pole (4 sub-cards)
40-561A-021-60X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI Low-Leakage Switched Guard Switching Solutions
They are based on the switched guard design principle, and the overall designs assure isolation resistances of up to 1013Ω. This high level of isolation resistance ensures accurate and reliable measurements, making our products ideal for high-precision semiconductor testing.
-
product
Aerospace
AcQ can perform custom developments compliant with ED12/DO-178B and ED80/DO-254 in various design assurance levels (DALs) for safety critical applications, using the ED14/DO160 for the environmental requirements. AcQ also offers standard products for various open standards like VMEbus, CPCI, PCI and other bus standards for test applications and other applications like GPS, display, actuators, data logging and -storage.
-
product
Data Center Load Bank
Mosebach Manufacturing Company
Mosebach’s Data Center Server Rack load bank, the SR family, is ideal for commissioning data centers. There are multiple models for varying voltages and power levels. The unit has a variable fan speed control which allows you to fine tune as desired.
-
product
50 Ohm Bridge / Freq Counter
* Generates a 3 to 30 MHz low level signal displayed on small 8 x 2 LCD * 50 ohm bridge supports tuning 50 ohm antennas * Adjust POT to find the resonate frequency of antenna * 30 turn POT allows easy smooth frequency adjustment * Bright red LED extinguishes when bridge is balanced * Function switching allows for use as frequency counter * 50 ohm termination included * measures 5.5 x 2.5 x 1.1 inches * 9 volt battery operation
-
product
IP67 DC Blocking Splitter Combiner
PD5033
INSTOCK Wireless Components, Inc
PD5033 is an IP67 outdoor, weather resistant, DC blocking, three way, RF broadband, 50 ohm, power divider, power combiner furnished with N type coaxial connectors. The passive Wilkinson design passes RF and the 10 MHz reference signal through both ports while blocking DC current. This configuration is typically used in combining applications to prevent passing DC to the sum and adjacent ports. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5033 is a bidirectional device capable of 40 W max microwave input power levels in both power splitter and combiner apps. See 3 way power divider input rating tables for additional power handling info.
-
product
500W - Single Output
XMS500 Series
*ITE & Medical Certifications (2 x MOPP)*Class I & Class II operation with Level B EMC*Compact 4 x 7.1" footprint*Suitable for B and BF rated equipment*Five year warranty
-
product
Digital/Pattern/PE Card
PEMU32
The PEMU32 represents a new level of MULTIFUNCTION for PXI-based instrumentation. Based on the proven architecture of the PE32, the PEMU32 offers high voltage PMU/DPS and pin electronics in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 256 bi-directional pins (8 boards). The PEMU32 also supports deep pattern memory by offering 32 M of on-board vector memory with dynamic per pin direction control and with test rates up to 10 MHz.
-
product
Electronic DC Load, 80V, 80A, 400W With/without Remote Interfaces
LD400 Series
Versatile solution for testing dc power sourcesConstant current, resistance, conductance, voltage and power modesWide voltage and current range, 0 to 80V and 0 to 80A400 watts continuous dissipation at 28°C (360W at 40°C)600 watts short-term dissipation (up to 60 seconds)Low minimum operating voltage of <1V at 40AHigh resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminals (front terminals 30A max.)Full bus control via USB, RS232 and LXI compliant LAN interfaces (LD400P)GPIB option (LD400P only)
-
product
BusTools Software Analyzer
AFDX-A
BusTools/AFDX-A is a Windows 7/10-based GUI application solution from Abaco Systems that establishes new levels of power, flexibility and ease-of-use for AFDX (Avionics Full Duplex Switched Ethernet) traffic monitoring, analysis and simulation. Available for use with our powerful CNIC interface, BusTools/AFDX offers an intuitive interface to view, log, analyze and generate AFDX network traffic at the Adapter, End System, Virtual Link (VL) and Port levels. Contact Goleta factory for listing of supported products.
-
product
Sound Level Meter
AWA5688
Hangzhou Aihua Instruments Co., Ltd.
* A handhold noise measuring instrument*. Multifunction and user- friendly sound level meter(sound level meter, integrating SLM, 1/1 OCT, 1/3 OCT analyzer, FFT analyzer, Noise dosimeter)* 240×320 color screen* Measurement range up to 133dB* Synchronously do integrating measure, statistical, real-time 1/1 OCT, 1/3 OCT, FFT analysis and noise dosimeter measure* Comply with IEC 61672 Class 2 and IEC61260 Class 2 and IEC 61252
-
product
Pressure/ Vacuum Sensors
There are three different types of pressures that can be measured using Premier Electrosystems' Pressure Sensors: Gauge, Absolute, and Differential. Gauge pressure is the pressure measured relative to the ambient atmospheric pressure.A typical application for a gauge pressure sensor is to measure liquid levels in a vented tank using the difference in hydrostatic pressure and ambient atmospheric pressure. Absolute pressure sensors will give the result relative to zero (a perfect vacuum). This is useful in applications where there is a direct effect of altitude on the pressure being measured. Differential pressure sensors measure the difference in pressure between two points. Differential pressure sensors are often used to monitor airflow in HVAC applications.
-
product
Soil Gas Flux Solutions
From idea to understanding, LI-COR has your soil gas flux research covered. No other solution is as flexible or delivers the same level of proven hardware, gas analyzers, and advanced data analysis software.
-
product
Broadband Planar Tunnel Diode Detectors
KRYTAR Broadband Planar Tunnel Diode Detectors are specifically designed for use in today's high-performance microwave instrumentation and systems. KRYTAR detectors are designed for such applications as power measurements, analyzing radar performance, leveling pulsed signal sources, AM noise measurements, system monitoring and pulsed RF measurements in ultra-broadband and mm-Wave applications.
-
product
16 Bit Digital Card
DB1600
The DB1600 is an inexpensive digital card that provides basic digital control capability without some of the more sophisticated features available on the DRM1650. The DB1600 allows for the control of 16 bits of data. The logic levels may be programmed anywhere within the range of 12 V.
-
product
6U RL1 VME Thundervbolt V-600 for 8-slot
SKY Computers provides one-stop-shopping for Defense contractors and integrators who need the complete spectrum of benign to harsh-packaged multiprocessing systems for their high performance needs. SKY's commercial grade SKYbolt 6U VME products have been ruggedized to two levels in the Xtreme product family. No other high performance embedded systems vendor provides this level of lifecycle support under one roof.
