Battery Capacity Testers
determine the condition of batteries to provide power.
See Also: Battery Testers, Battery Checkers, Lead Acid Battery Testers, Battery Conductance Testers, Battery Load Testers
-
Product
Flexible Pick And Place Machine With 128-feeder Capacity
MC385V1V
-
The high-precision MC385V1V Pick and Place system ensures accuracy and repeatablity with high-quality ballscrew drive, linear encoders, and full vision alignment. Programming and operation are made easy with mature, fully supported Windows-based software. Machine holds up to four 32-port feeder racks for a maximum feeder capacity of 128 tapes. Waffle trays and cut strip tape holders can be used in the placement area.
-
Product
Intelligent Battery Charger-Analyzer for Large Battery Systems
SuperMasterCharger
-
The SuperMasterCharger is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMasterCharger can satisfy the requirements of most large ( 10 A-hr to 100 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
Product
Battery Conductance Tester
FST-8000
-
Foresight Electronics Co., Ltd.
Profsional battery conductance tester for Lead-acid stationary (wet, flooded, gel, AGM, VRLA) battery cells/blocks, to measure actual capacity and aging for UPS, telecom, industrial, vehicle, solar or other applications' small and large battery banks.Battery Conductance Tester is a portable digital measurement device for testing lead acid stationary batteries health and aging condition precisely within seconds.
-
Product
Low Capacity (inch-ounce) Reaction Torque Sensor
RTS SERIES
-
The RTS Series torque sensors were designed to fill the need for accurate torque measurements below 62.5 in.lbs. without giving up stiffness or sensitivity to forces from other directions. They are manufactured from sensor quality aluminum and anodized for long term durability. Bonded foil strain gages and materials of the highest quality are installed assuring high reliability. The four bolt hole pattern with the use of our O.D. or I.D. pilots on either end allows simple adaptation to any application.
-
Product
International Wireless 6V/12V Battery and 12V/24V System Tester
SBT1
-
Schumacher Electric Corporation
PERFORM BATTERY AND SYSTEM TESTS WIRELESSLY FROM YOUR SMARTPHONE OR TABLET.For 6V and 12V automotive batteries (SS EFB and AGM included) and 12V/24V charging/starting systemsEasy and fast Bluetooth® pairing Works with SBT1 SchulinkTM app, which includes eight language settings.Performs Battery Test, System Test, Start-Stop Test and EV Battery Test Email or text test results – stores 2,000 test records Test batteries with as little as 1.5V3 LED indicators (Blue: Connected, Green: Power, Red: Trouble)On/Off button20-inch cable with durable clamps3.7V rechargeable internal lithium ion batteryContents: (1) SBT1 tester (1) Manual
-
Product
Automatic Battery
BATM
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
Product
High-Precision Battery Tester with Integrated Chamber
-
Arbin's High-Precision Battery Tester (HPS) offers a turn-key solution with state-of-the-art technology, ensuring unmatched accuracy and precision.
-
Product
Standard 1.24 (35.00) - 2.94 (85.00) Battery Probe
CCA-006
Battery Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 78Full Travel (mm): 1.98Recommended Travel (mil): 40Recommended Travel (mm): 1.02Overall Length (mil): 669Overall Length (mm): 16.99
-
Product
Automated Coherent Receiver Tester
CoRx Tester.
Receiver Tester
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
Product
Battery Impedance Meter
-
Operation is fast and simple. Just press the spring-loaded probes onto the two poles of the battery. After 1.5 seconds, the unit beeps (indicating good contact) and displays the battery voltage and either the number of siemens or milliohms, depending on the knob setting. The display continues to show these numbers after the probes are removed; it resets only when the probes are pressed onto the next battery. The impedance and voltage of any battery between 1.2 and 60 volts can be read. Because of the wide range of voltages, even single low-voltage cells, such as NiMH, can be measured. The manufacturers of some batteries specify impedance in milliohms while other specify in siemens (one divided by the resistance in ohms). This meter will display both types of impedance for any given battery. Accuracy is +/- 2% of the value.
-
Product
Extended Battery Banks
-
Falcon Electric’s extended battery banks provide extra battery runtimes from minutes to hours with our SSG and SSG-RP online industrial UPS systems. The rackmount banks are easily daisy-chained with DC plug-and-play connectors. Simply determine your application requirements and select one of these battery bank options.
-
Product
Battery Backup IC
-
Analog Devices offers a range of supervisory circuits that offer a complete single chip solution for power supply monitoring and battery control functions in microprocessor systems. Functions include microprocessor reset, backup battery switchover, watchdog timers, CMOS RAM write protection, and power failure warning.
-
Product
Battery Module
-
Each Gavia Battery Module contains several independent "smart" Li-Ion battery packs and battery chargers. Each battery pack is monitored for health and operational information, and the battery packs are protected against short-circuit and overcharge. The Battery Module also contains an intelligent power management processor.
-
Product
Advanced Battery Conductance/Electrical System Tester
PBT Series
-
Building upon the success of the PBT-100, the first battery conductance tester built for the professional technician's toolbox, the PBT-200 offers these additional capabilities: Shows available power in CCA in addition to condition and voltage. Bad Cell Detection. Advanced Starter Testing: Down arrow displays the captured low voltage from cranking the engine for simple starter analysis.
-
Product
Laptop Battery Pack Tester 20V10A
TOB-BTS-20V10A
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channel Battery Analyzer (10A 20V per Channel) with Laptop & Software for All Types of Batteries &Laptop battery Packs. TOB-BTS-20V10A Laptop Battery Pack Tester 20V10A is a 8 channel battery analyzing system for Li-ion, LiFePO3, Ni-MH, Ni-Cd, and Lead acid battery packs with voltage up to 20V and current up to 10A per channel.
-
Product
Battery Simulator
G5.BAS
-
The G5.BAS series is bidirectional regenerative. It was developed specifically for the simulation of energy storage devices and batteries and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3.
-
Product
Battery Management Controllers
-
Renesas offers a dedicated single-package solution with an MCU and analog front end (AFE) for battery management systems that constantly monitors the battery state.
-
Product
Micro Capacity Type High-Speed Rotation Torque Detector
TH-3000/3000H Series
-
TH-3000 series is a torque detector designed for very low torque (less than 2 N· m) with high response and high accuracy. Two types are available depending on your applications.
-
Product
CTEK MUS 4.3 TEST&CHARGE Battery Charger and Tester
56-959
-
The MUS 4.3 TEST&CHARGE combines an advanced micro-processor controlled battery charger with a battery and alternator test function to provide the ultimate in battery testing, charging and maintenance.
-
Product
Battery Testing Machine
-
Dongguan Kejian Instrument Co., Ltd.
Test method is to use test sample cell on a plane, a diameter of 15.8 mm (5/8 inch) rods on the cross placed in the center of the sample.one 9.1 kg or 10 kg weight from a certain height (610 mm or 1000 mm) fell to the samples.Cylindrical or square battery in accepting the impact test, the vertical axis parallel to the plane, vertical steel column longitudinal axis.The longest axis vertical steel column square battery, the bedding face perpendicular to the direction of impact, each battery only accept an impact test.
-
Product
12V 0-500 Amp Carbon Pile Battery Load Tester and 12/24V Electrical Systems Tester
6042
-
• Test batteries up to 1000 CCA• Interprets data from the charging/starting system on easy-to-read LCD displays• Shows positive and negative amps for easy diagnosis of current leakage problems• 0-500 Amp variable carbon pile load tester• Unique curved carbon discs ensure maximum contact, fewer hot spots, smoother operation and longer life• Heavy-duty single extruded leads for testing up to 15 feet apart• Test electrical systems on 12/24 Volt systems• Test all battery types• Ideal for testing remotely mounted batteries accurately• INCLUDES: Model 6043 1000 Amp AC/DC Inductive Amp Clamp for checking starter draw or parasitic drain test, also can be used with conventional multi-meters; heavy duty, two wheel tilt-back cart with 8” wheels and 2 trays.• Made in USA of US and Global Components
-
Product
Battery Charger-Analyzer for small battery systems (up to 10A-Hr)
24-400xg
-
The 24-400XG is an instrument designed to charge, trickle charge and analyze (discharge) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries.With its multiple modes of operation of Constant Current Charge (dual and single rate), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge (analysis), Resistance Discharge (analysis) and Full Discharge (deep cycle), the 24-400XG can satisfy the requirements of most small (0 to 10 A-hr) rechargeable battery systems.The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit (no load) and Overvoltage conditions.Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights inform of the status of the operation.
-
Product
Battery Analyzer
IC8A
-
Operationally, the IC8A has all the same features same as the MB73+, MB73P+ & IC50A models. Being universal – like other members of the family – any cell combination can be catered for. The IC8A also supports use of our the cell monitor for accurate cell charging and capacity testing plus cell balancing. If you require the results to be printed please view our new IC8P model.
-
Product
Advanced Battery Tester
DBT-12+
-
The tester enables safe measurement of voltage, current rating, state of charge and state of health for 12V and 6V batteries. The device is powered by an internal battery, so it can test even discharged batteries and can be conveniently used as a voltmeter.
-
Product
Scienlab Charging Discovery System (CDS) – High-Power Series
SL1047A
Battery Test Platform
The Scienlab Charging Discovery System – High-Power Series from Keysight enables you to test charging interfaces of electric vehicles (EVs) and EV supply equipment (EVSE) during high-power charging up to 1,500 V DC and ±600 A DC. With the CDS can perform all necessary conformance and interoperability tests according to worldwide charging standards. Our new solution, which features the separate Scienlab Cooling Unit with interchangeable liquid-cooled charging adapters, also enables a high-power upgrade of the SL1040A Scienlab Charging Discovery System - Portable Series.
-
Product
Battery Capacity Analyzer
-
Foresight Electronics Co., Ltd.
At present, Iead acid storage battery’s maintenance is applied for the check of Float voltage of battery at home, it has been found that Voltage is irrelevance with Capacity of battery, because Voltage is only to show battery’s basic parameters.Internationally, Resistance test is widely applied in daily battery maintenance instead of Voltage check, because Resistance is reflection to internal parameters of battery with high precision worldwide.
-
Product
Standard 0.95 (26.90) - 4.50 (128.00) Battery Probe
CP-2LB-12
Battery Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 128Full Travel (mm): 3.25Recommended Travel (mil): 118.1Recommended Travel (mm): 3.00Overall Length (mil): 472Overall Length (mm): 12.00Overall Length Remark: Overall length does not include tail.Recommended Drill Size: #53 or 1.51 mmRec. Mounting Hole Size (mil): 61Rec. Mounting Hole Size (mm): 1.55
-
Product
Battery Analyzers
BA6010 Series
-
The BA6010 Series battery analyzers measure voltage and resistance of modern battery technologies with high accuracy, resolution, and speed. Additionally, these instruments provide auxiliary measurement parameters inductance, capacitance, dissipation factor, impedance, quality factor, reactance, and phase angle in degrees and radians. The BA6010 Series is suitable for characterizing battery chemistries that are responsive to a 1 kHz AC stimulus signal including lead acid, lithium and alkaline type batteries used in consumer products, electric vehicles, power backup, security, and fire alarm systems.
-
Product
Laboratory Battery Tester With Integrated Chamber
-
Compact and versatile, our portable desktop solution integrates Arbin's advanced testing features.
-
Product
Battery Load Tester
Battery Beak
-
Cross the Road Electronics, LLC
The Battery Beak is a battery load tester that is capable of delivering an 18 amp load and measuring a batteries internal resistance, state of charge (SOC), and can determine the overall health of the battery. The Battery Beak supports all battery chemistries but has additional features to determine battery health for both Lead Acid and NiMH chemistries and supports a variety of AmpHour/Voltage combinations.
