Humidity Chambers
Controlled analysis of a product exposed to humid conditions.
See Also: Environmental Chambers, Chambers, Temperature Chambers
-
Product
Environmental Test Chamber
-
Labtone Test Equipment Co., LTD
Environmental test system, Electro-dynamic Shaker, Shock Test Systems, Drop Tester, Bump Test Systems, Combined Environmental Test Systems
-
Product
Humidity and Temperature Measurement Accessories
-
Find our selection of most frequently used accessories such as filter and filter carriers to protect your sensor against mechanical influences or a range of accessories for mounting, connecting, installation, maintenance and calibration of your humidity and temperature instruments.
-
Product
Temperature Humidity Meters
-
Measure and record temperature and humidity readings anywhere.
-
Product
Thermal Shock Chambers
-
We provide a large selection of thermal shock chambers to accommodate various types of product testing. Thermal Shock Chambers perform tailored environmental stress screening of component and board electronic assemblies. Our unique chamber design transfers product between two extreme temperature-controlled chambers, passing equal volumes of high velocity conditioned air over the product and resulting in rapid product temperature changes. The induced thermal stresses can reveal hidden manufacturing defects in electronic sub-assemblies and other components by the expansion and contraction of critical parts.
-
Product
Walk-in Environmental Chambers
EWS-SERIES
-
Mono-block/Pre-fabricated design EWS-Series Walk-in Environmental Chambers with custom-built features to meet testing needs of large-sized test specimens
-
Product
Condensation Chamber
-
Wewon Environmental Chambers Co, Ltd.
The condensation test chamber does not need special installation conditions, just need to connect to the ordinary power supply and running water can be used normally. The functional diversity of the equipment, fast and low operating costs make the machine a very high cost performance condensation testing machine in the market. The machine can be programmed to control three different test effects: Humidification, natural cooling and drying, and the corresponding temperature and running time of each test, and set the total time of program running and the number of cycles. The condensation tester has an automatic water replenishing device. When the water temperature exceeds the upper limit, there will be a protection device for safety warning, and it is very safe to use.https://www.wewontech.com/condensation-chamber/
-
Product
Thermal Shock Chamber
ATS Series
-
Thermotron thermal shock chambers meet a variety of testing needs and come in three configurations: vertical, horizontal, and double duty. A product transfer mechanism automatically transfers products under test from hot to cold zones and back when programmed in the controller.
-
Product
Walk-In Conditioning Test Chamber
-
Weiber Walk in Conditioning Test Chamber offers an ideal apparatus for conditioning materials at non-ambient temperatures. Now researchers, engineers, and technicians have a simple and cost effective method to condition samples prior to testing. Laboratory Conditioning Chamber is designed for the conditioning of samples prior to testing, provides conditions from 20% to 98% RH ± 2 and 0°C to 94°C ±0.5°C.Conditioning Test Chambers offers ideal humidity and temperature conditions required for testing the effect of environmental changes on the product. The chamber can be widely used to evaluate the durability of various products. Weiber delivers customized products at the most economical rate and within the limited delivery period.
-
Product
Temperature, Humidity, Bar. Pressure Transmitter
T7411
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Built-in pressure sensor.
-
Product
Temperature/ Relative Humidity
-
Specialized data loggers and sensors from Onset that accurately monitor and record indoor/outdoor environmental conditions.
-
Product
AGREE Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood have 13 process and 5 times quality control to ensure the accurate control of all details for AGREE Test Chamber, EES and vibration test chamber, Temperature humidity and vibration test chamber, Comprehensive test chamber, Agree chamber
-
Product
Compact EMC Test Chamber
EMC-3C
-
This compact 3 meter test range will settle into test areas of limited space while continuing to produce exceptional performance for EMC measurement. Emission quiet zones of up to 1.5m are accommodated with very repeatable results. Suitable for EMC pre-compliance emissions and compliant immunity testing.
-
Product
Test Chambers
-
The left-hand axis scales the level of the 100 measurements and the right-hand axis displays the uncertainty to a statistical confidence level of 95%; proving the repeatability is better than +/-0.25dB between the measured values. Guaranteeing repeatability, accuracy and correlation across Lab’s, across Production lines and across the World
-
Product
Temperature & Humidity Testing
-
DATASYST Engineering & Testing Services, Inc.
DATASYST can simulate both high and low temperature with humidity conditions. Cycle rates are dependent upon individual chamber capabilities and whether or not a unit under test is powered or not. DATASYST provides humidity testing for a range of industry specifications and can work with you on your customized testing requirements.
-
Product
RF Diagnostic Chamber
DST200
-
The R&S®DST200 RF diagnostic chamber is the ideal environment for RF analysis during development. It supports a wide range of radiated test applications for wireless devices and fits on any R&D lab bench, where it can be used at all times during the product design and optimization phase. The R&S®DST200 effectively assists in achieving high first-time pass rates during final type approval, which saves time and money.
-
-
Product
Solar Spectrum Test Chamber / Solar Radiation Test Chamber
-
WEIBER Solar Spectrum Test Chambers are one of solutions to be utilized in large scale PV testing program. We offer customized as well as standard multidimensional test program for PV modules in reasonable prices. This system delivers the weathering stress representative of long term outdoor exposure.Our flexible system can be designed according to our test requirements, to suit environmental test conditions like volume, temperature, humidity solar radiation intensity and other measuring instruments. Weiber provide Solar Radiation Test Chamber.WEIBER solar test system are recognized for superior solar simulation environmental Testing, evaluating outdoor use product reliability, quality & safety. This technology allows for very high concentrations of UV energy without excessive heating of test samples. Custom mounting and cooling can be added depending upon specific material exposure requirements. MHGs (metal halide global lamps) are used as radiation source. Weiber provide Solar Simulation Test Chamber.
-
Product
UV Test Chamber
-
Wewon Environmental Chambers Co, Ltd.
* UV test chamber simulates damaging effects of long term outdoor exposure of materials and coatings by exposing test samples to varying conditions of the most aggressive components of weathering – ultraviolet radiation, moisture and heat. * UV test chamber use fluorescent lamps to provide a radiation spectrum centered in the ultraviolet wavelengths. Moisture is provided by forced condensation, and temperature is controlled by heaters. Based on your testing sample’s size, We has two options uv test chambers for choice.
-
Product
Temperature Chambers For Thermal Tests
-
Before anything reaches out for market distribution, you would need to determine its exact quality and performance to that follows to the point with readings. Thermal and environment testing are some of the most positive aspects to get your materials tested for their underlying performance capacity and reliability in quality.
-
Product
Rain Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Rain Test Chamber is used to test anti-rain and waterproof performance for products, the products such as .steam locomotive lamps, wiper performance, waterproof bands, motorcycle instruments, defense industry, navigation systems, missiles, radar cone top, aerospace industry, IEC IP code specifications that need an additional discussion.
-
Product
Environmental Stress Screening (ESS) Chamber
ESS
-
Developed to help electronics manufacturers detect product defects and production flaws, Environmental Stress Screening (ESS) forces infancy product failures that would otherwise occur after final assembly and product delivery. ESS’s goal is to improve profitability by eliminating defective products. ESS Systems can meet individual performance needs, product loading, and throughput requirements. Thermotron has the experience to provide the best solution for ESS testing at your company.
-
Product
Benchtop Test Chambers
MicroClimate
-
The MicroClimate 1.2 cubic foot benchtop test chamber is capable of simulating a full range of temperature and humidity conditions. This environmental testing chamber is designed to provide users with a compact unit for testing small components and products.
-
Product
Temperature / Humidity / Dew point Meter
MT-4616
-
Ideal for metallurgy, electronics, chemical contamination or other high temperature environment and more
-
Product
Sand And Dust Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Sand and dust test chamber is also referred as dust-proof chamber, which is able to simulate the sand storm by putting the test piece in the chamber to judge the damage of sand-and-dust weather to products. Equipment is mainly applicable to determination of sealing performance of product shells based on the IPX5 and IPX6 degrees. Testing machine features a flow of air carrying dust in a vertical circulation, resulting in cycle use of sand during the test. Sand and dust testing has great significance to master the specimen’s performance to defend the penetration of dust particles, to withstand the abrasion of sands.
-
Product
Three Meter Fully Compliant Chambers
-
3 Meter Fully Compliant semi-anechoic chambers offer semi-anechoic radiated emissions (RE) and fully anechoic radiated immunity (RI) compliance test capability for most international EMC compliance regulations.
-
Product
temperature, humidity, bar. pressure transmitter
T7410
-
Built-in relative humidity, temperature, atmospheric pressure sensors. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Temperature, Humidity, CO2 Transmitter
T6340
-
The transmitters are designed for online measurement of temperature (C or F), relative humidity and carbon dioxide concentration of air without aggressive ingredients. Measured temperature andrelative humidity are recomputed to following humidity expression: dew point temperature, absolutehumidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Custom Designed Environmental Chambers
-
Our strength lies in our ability to provide custom solutions to complicated testing needs. Our world-class design engineering team has the experience needed to tailor environmental test chambers to work in unison with existing machinery, unique size requirements, and custom testing conditions. Whether the environmental chamber is used for testing microchips and processors for leading computer manufacturers, or temperature, humidity, and altitude rated chambers for leading aerospace and defense contractors, our detail oriented team works to provide solutions that meet or exceed project requirements and industry standards for quality.
-
Product
Environmental Chamber
REXMED REC-400
-
MOD. REC-400, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,506 Watts, 11,962 BTU/hr, 3,020 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L50 X W60 X H75cm, Capacity: 225L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Thermal Shock Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Chamber provide the sudden temperature changes between extreme cold and extreme hot from -65℃ to 150℃ (customized available), specially for environmental stress screen test of the industries that rely on thermal testing, such as component, board electronic assemblies, defense, material stress, consumer products etc. The thermal shock test can cause faulting or cracking by the expansion and contraction on the products, indicates the hidden manufacturing defects. Bell’s Thermal Shock Chamber ensure you to launch qualified product to the market.
