-
product
Test Fixture with API
TA-14VG
The TA-14VG test fixture is based on the requirements for the Integrated Test Procedure for the VG-14A assembly as shown in the OEM maintenance manual. The panel also contains a test point breakout for the units main connector as well as one for the VG-401 base. The VG-401 breakouts provide an in series connection that will allow easy access to the gyro's signals and also provides a way to monitor rotor current. The panel also contains a variac to allow for line voltage adjustment.
-
product
Pulse generator
9355-1
Solar Model 9355-1 Pulse Generator is designed to provide impulse excitation by means of an injection probe placed around interconnecting cables or power wires. The unit uses a charged transmission line (50 ohms) to generate a pulse with less than 2 nanoseconds rise and fall time, and duration of approximately 30 nS, calibrated in a 50 ohm fixture to deliver up to 5 amperes at a rate of 30 p.p.s. for one minute as required by MIL-STD-461D/E, test method CS115.
-
-
product
ICT/FCT-Fixtures Max UUT 370 × 300 mm (wxd)
CK-2 Large (Hold-Down Gate) / 230158
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
product
Vacuum Test Fixtures
Series 63
The VT Series 63 vacuum test kits provide both an affordable and versatile solution for printed circuit board testing requiring vacuum actuation and a Genrad 2270/71 interface. The VT Series 63 kits, available in Single and Dual Well models, incorporate a robust design which includes a variety of chassis sizes and depths for additional hardware and components used in Functional Test. Tooling holes on both the top diaphragm plate and probe plate for accurate drill datum. The interface will accommodate up to 11 I/O blocks with a single vacuum port.
-
product
16-Station Testing System
The ElectroPuls 16-Station testing system performs high cycle fatigue testing on multiple samples simultaneously, with a fatigue-rated load cell included on each station. The fixture uses a carousel designed with high stiffness and low mass to enable high frequency testing and reduce test time.
-
product
PXI 1A Fault Insertion Switch 11-Channel
40-195-101
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
product
Pod/Nest Fixtures
Nest and Pod Fixtures are used to test components and sub-assemblies. They typically are built in an array and the devices under test are subjected to tests that simulate operating conditions or life-cycle testing. Test Head Engineering is experienced in providing nest and pod testers that meet the connectivity, ergonomic and mechanical requirements of component testing.
-
product
Wave Profiler Fixture
KIC® Wave Surfer™
The KIC Wave Surfer is a self-contained system that provides critical data on wave solder machine set up and performance. Used in conjunction with your SlimKIC 2000 and the KIC 2000 software, you can ensure your wave solder machine is set up and performing properly.
-
product
Clamshell Type Mechanical Fixtures
Series 11
The MT Series 11 dual well mechanical kits are an affordable solution to printed circuit board testing with the advantage of testing two devices. These can be similar devices, or devices that are used together in a functional test. The Series 11 Kits have the same available features and options as the Series 10 Kits.
-
product
Manual Fixture Kit
230356 – CMK-07
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
PhyView Analyzer
The PhyView Analyzer dramatically simplifies the task of Ethernet 10/100/1000 interface testing in finished products without the need for test fixtures, test signals, scopes, and probes.
-
product
Qualification Hardware & Sockets
Reltech Limited holds over 35 years’ experience in the design and manufacture of all types of qualification test hardware. Our advanced technology products include: HTOL Boards (Mother and Daughter cards) Burn-In Boards HAST Boards THB (humidity) Boards Burn-In Modules and frames Dynamic Driver cards (Digital, Analogue and Mixed signal) Back Planes Voltage regulator cards Custom electro-mechanical assemblies DUT Cassettes and test Fixtures
-
product
PCI Express Oscilloscope Software Compliance Test
Rohde & Schwarz offers automated compliance test solution of PCI Express Gen 1.1, 2.0 and 3.0 interfaces. The test wizard of the Rohde & Schwarz ScopeSuite compliance test software guides the user via illustrated step-by-step instructions. The option supports add-in card and system motherboard testing. It is based on the PCI-SIG standard post processing analysis software and utilizes PCI-SIG test fixtures. A configurable test report documents the test results.
-
product
Vacuum Test Fixtures
Vacuum fixture kits for Pylon block fixture, Teradyne, Keysight, Digitaltest,Seica, Cobham (Aeroflex), ATX exchangeable system.
-
product
Spectrum Analysis For E5081A Up To 20 GHz
S960904B
The Keysight S960904 spectrum analyzer (SA) software application adds high-performance spectrum analysis to the E5081A ENA-X up to 20 GHz. With fast-stepped FFT sweeps resulting from optimized data processing, the SA software application provides quick spurious searches over broad frequency ranges. The application enables simultaneous spectrum measurements using test and reference receivers. The multichannel SA pairs with the internal swept-signal generators for efficient measurements of spurious signals emanating from mixers and frequency converters. The SA application uses source-power and receiver-response calibration and fixture de-embedding, providing highly accurate in-fixture and on-wafer spectrum measurements.
-
product
DDC (Dual DIMM Carrier) DIOS Adaptor
JT 2702/DDC
The JT2702 Digital 256 channel JTAG I/O module. JT2702/DDC (Dual DIMM Carrier) is a DIMM DIOS accessory product. It is typically used in custom test adapters or fixtures where a large number of digital I/O channels are required with a minimum space overhead.
-
product
Clamshell Type Mechanical Fixtures
Series 10
Semco MT Series 10: An affordable solution for testing of printed circuit boards.
-
product
VP Power Meter
UVP-365
This is the standard measurement instrument to measure absolute UV vaiue. All SAN-EI's UV light source fixtures are measured by this meter.
-
product
Mechanical Testing
The Mechanical Testing Department at IMR is well equipped to perform most standard mechanical testing, as well as specialized tests designed to the customer's requirements. A complete in-house machine shop supports the department with precise specimen preparation and fixture fabrication.
-
product
DC Power Module, 8 V, 6.25 A, 50 W
N6732B
The Keysight N6732B 50 W basic DC power module provides programmable voltage and current, as well as measurement and protection features at a very economical price. Use this module to power your DUT or ATE system resources, such as fixture control.
-
product
Light source
UVM-MP
Measurement of maximum of 6 points is possible. By use of thee sensor amplifier box, distance between the light receiving inlet and the controller can be extended to 10 meters. Measurement start signals can be independently output by remote control. This is useful for the light source fixtures integrating shutter mechanism.
-
product
USB-C® Short Channel Rx Precet. Test Fixture
AUT20098
*Easy swap between CC1 and CC2RP & RD Mode: In the older version of the USB-C full breakout board, users had to manually set the jumper with a short pin. But now users can easily swap between the two by just moving the switch.*In the previous version, the soldering joint of Test Fixture Host Fixture 1A gets worn out quickly from repetitive plug and pull. This newly designed fixture is more durable and users can easily replace the worn out SMA connectors with new ones.*DC-in Jack is upgraded to +5V USB C portA boost in user experience as it makes setting up easier.
-
product
Emergency Battery Power Supply Test Fixture
TA-61
This test fixture provides an interface to test and chargethe Radiant type RPS1-B Emergency Lighting power supply. The panel includes the switching required asdescribed in the CMM along with an analog currentmeter for monitoring the charging current. This panelprovides simple testing for the corporate flight departmentor DOM.
-
product
DC Power Module 0 To 5 V, 0 To 10 A, 50 W
N6731B
The Keysight N6731B, a 50 W basic DC power module, provides programmable voltage and current, as well as measurement and protection features at a very economical price. Use this module to power the device under test or ATE system resources, such as fixture control.
-
product
Universal Grid Tester
For higher quantities universal fixture tester are the best economical solution.They combine highest throughput with affordable fixture technology especially in comparison to testers utilizing dedicated fixtures.
-
product
In-Line 2-Module In-Circuit Test System; i337x, Series 5i
E9988E
Short wire fixturing eliminates problems commonly found with long wire fixturing, such as noise and deterioration of test stability. This translates into transportable, repeatable and stable tests on your i3070 Series 5i, even if you need to deploy tests halfway across the globe, or on different manufacturing sites.
-
product
Test Fixture Kits
Our test fixture kits provide cost effective solutions to printed circuit board testing and other devices under test. Our modular kits are available in multiple sizes and configurations. They can easily be customized if our standard doesn’t meet your requirements. Removable side panels for ease of fabrication for I/O connections, switches or other hardware.
-
product
Small Footprint Flex 20 ATE
Flex 20
The Flex 20 is floor mounted but maintains a small footprint on the shop floor. A VPC S6 interface is normally used on this system allowing multiple test fixtures to be used with the system.
-
product
Reel to Reel Non-Contact OS Inspection System for TAB/COD/TCP/TBGA
TRV
*Most suitable mechanism for non-contact inspection*Sprochet-less transfer decreases products damage.*Easy operation by Fixture alignment mechanism*Equipped with Tracing Test function
