MIPI
collaborative alliance devoted to developing mobile interface specfications.
See Also: Interfaces, Serial Interfaces, Parallel Interface, Bus Interfaces, UI, Interface Adapters, I3C
-
product
MIPI Test Fixtures & Software
The UNH-IOL has been a contributing member of the MIPI Alliance since 2007 and tests all mobile devices looking for MIPI conformance and physical layer testing including C-PHY, D-PHY, DSI, and CSI-2. All UNH-IOL MIPI Test Fixtures and Tools are available to member and non-member companies. Below are just some of the MIPI Solutions we offer. For a full list please visit our MIPI Test Fixtures page.
-
product
MIPI PHYs
Arasan MIPI PHY’s are readily available and in production with multiple foundries from 16nm to 180nm. Our PHY’s are designed for low power on the most advanced nodes for the mobile market while also targeting the automobile market on specialized nodes where extreme temperature tolerance is required.
-
product
MIPI Soundwire Total IP Solutions
Soundwire
Soundwire is suited for small, cost-sensitive audio peripherals such as modern digital class-D amplifiers and digital microphones. The Total MIPI SoundWire IP Solution from Arasan enables early adopters the fastest path to adoption of this new standard by offering a comprehensive IP package that includes the Verilog RTL source code for Master and Slave, fully validated for compliance with the standard, a comprehensive test environment with a compliance suite for verification of the IP package, a SoundWire Hardware Development Kit (“HDK”) for FPGA prototyping, a SoundWire protocol analyzer and a complete SoundWire software stack.
-
product
MIPI SLIMbus
A typical mobile device has many low-speed/bandwidth peripherals connected to the host processor, which include microphones, speakers, sensors and many others. There is a need for a standard bus that enables multiple audio channels, peer-peer communications and lower pin count on the host processor. The MIPI alliance has defined the SLIMbus specification which provides a standard, robust, scalable, low-power, high-speed, cost-effective, two wire multipurpose interface that supports a wide range of digital audio and control solutions for mobile terminals.
-
product
MIPI M-PHY v5.0 Receiver Conformance Test Software
N5991MM5A
The Rx solution including Station Configurator and Valiframe maximizes the usage of test instruments, providing automated system calibration as well as conformance testing according to the M-PHY 5.0 test specification (CTS).
-
product
MIPI Camera Serial Interface
CSI
Arasan provides a Total MIPI CSI-2 IP Solution supporting two options: MIPI CSI-2 v1.2 for D-PHY physical interface only, and MIPI CSI-2 v1.3 for the new MIPI C-PHY v1.0 and D-PHY v.1.1, v1.2, and a future v2.0. Arasan offers the C-PHY in a combination configuration that supports both C-PHY interfaces and D-PHY interfaces. Our implementation makes efficient use of the high frequency signally pins for a minimal overhead to support both physical interfaces.
-
product
13MP MIPI Camera Module
e-CAM130_CUMI1820_MOD –
e-CAM130_CUMI1820_MOD is a 13MP MIPI Camera Module. This small form factor 13MP camera module comes with S-Mount lens holder. It is based on AR1820HS – an 18MP CMOS Image sensor from Aptina™ / ON Semiconductor® and has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs all the Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images and video and the optional MJPEG compression. Though the AR1820HS is an 18MP image sensor, the e-CAM130_CUMI1820_MOD supports only up to 13MP resolution.
-
product
4K MIPI NVIDIA® Jetson TX2/TX1 Camera Board
E-CAM131_CUTX2
e-CAM131_CUTX2 - 13MP Jetson TX2/TX1 camera board is a 4-lane MIPI CSI-2 camera solution for NVIDIA® Jetson TX2/TX1 developer kit. This camera is based on 1/3.2" AR1335 CMOS image sensor with advanced 1.1µm pixel BSI technology from ON Semiconductor® and an integrated high-performance image signal processor (ISP) that performs all the Auto functions (Auto White Balance, Auto Exposure control). It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement.
-
product
5MP RAW MIPI Camera Module (Bayer)
e-CAM58_MI5680_MOD
The e-CAM58_MI5680_MOD is a 1/3.2" optical format, 5MP RAW MIPI Camera Module based on OmniVision's OV5680 CMOS image sensor and it provides RAW Bayer format image output through its 2-lane MIPI CSI-2 interface. Combined with the 1.75 micron pixel size and the OmniVision's OmniBSI-2 pixel technology, this autofocus camera module provides best-in-class sensitivity and excellent noise performance. The small form-factor camera module also contains the voice coil motor (VCM) based lens mechanism for adjusting the focus position of the built-in lens and the same can be used with an external back-end ISP to implement the autofocus capability.
-
product
MIPI Test Fixtures and Tools
In order to support our MIPI test services, UNH-IOL has designed and created test fixtures and software tools to aid in performing C-PHY, D-PHY, DSI, and CSI-2 testing.
-
product
SMARC V1.0 SoM With IMX6 Quad/DualLite 800 MHz (Industrial) SoC, 1GB RAM, 4GB EMMC, GbE LAN, Audio, CAN, MIPI And PCAM
SCM120
*SMARC 1.0 (82 x 50 mm)*Ultra low power consumption Cortex™-A9*2 CAN 2.0B*24-bit TTL signal*LVDS/HDMI 1080P*10/100/1000 Mbps Ethernet*Linux3.0.35/Android 4.3*Audio
-
product
MIPI Radio Front-End
RFFE
Mobile phone radios have developed into highly complex, multi-band and multi-standard designs that often have multiple radio frequency (RF) signal chains. The MIPI Alliance Specification for RF Front-End Control Interface (RFFE) was developed to offer a common and widespread method for controlling RF front-end devices. The RFFE Master IP core typically resides in the RFIC in a mobile platform, and utilizes the RFFE bus to identify, program and monitor the registers in RF front end Slave devices through programmed IO. It is designed to support existing standards such as LTE, UMTS, HSPA and EGPRS, and is usable in configurations ranging from single Master/single Slave to multi-Master/multi-Slave.
-
product
5 MP MIPI Camera Module
e-CAM52A_MI5640_MOD
e-CAM52A_MI5640_MOD is a 5MP MIPI camera Module that features OV5640 image sensor. This MIPI CSI camera module streams HD (720p) @ 60fps and full HD (1080p) @ 30fps. Any processor system like I.MX6, OMAP4430, OMAP4460, OMAP35x, AM37x, DM37x that has a MIPI CSI-2 interface can integrate the e-CAM52A_MI5640_MOD.
-
product
Low Power FPGA Featuring Hardened MIPI D-PHY, LVDS, SLVS, SubLVDS, & Open LDI Bridging
CrossLink
*Two 4-lane MIPI D-PHY transceivers at 6 Gbps per PHY*15 programmable source synchronous I/O pairs for camera and display interfacing*Available in amazingly small 2.46 mm x 2.46 mm WLCSP packages and BGA packages with 0.4 mm, 0.5 mm and 0.65 mm pitch
-
product
MIPI M-PHY V5.0 Receiver Test Software (Frame Generator)
N5991MM5E
Generate MIPI M-PHY 5.0 sequences and signaling at HS-GEAR5 and lower speeds, for debugging, troubleshooting, and conformance test purposes, using the N5991MM5E Frame Generator software, for the M8040A BERT platform.
-
product
BusFinder Protocol and Logic Analyzer
Acute BF7264B+
*Two-in-One Analyzer (Protocol and Logic)*PC-based, 64 channels*USB 3.0 interface, 12V power adapter*32Gb total memory*NOW supporting MIPI D-PHY 1.2 (includes MIPI CSI)*NOW UFS2.1 supported with new BF7264B+
-
product
CSI & DSI Protocol Generator
Envision X84 CSI&DSI
With comprehensive support for MIPI CSI-2v2 and DSI-2 specifications, Teledyne LeCroy’s Envision X84 generator platform provides the industry’s most accurate and reliable generation of MIPI camera and display protocols for fast debug, analysis and problem solving. The Envision X84 exerciser is loaded with innovative features that help uncover elusive protocol errors and is the intelligent choice for any camera and display validation needs. Using the same hardware platform as the Envision X84 C/D-PHY protocol analyzer, the Envision X84 offers the most flexible solution for MIPI Camera and Display validation and debug.
-
product
GMSL3
FRAMOS is the first company in the market to integrate Analog Devices’s new GMSL3 technology into an embedded vision environment. GMSL3 can transmit high frame rates (4K, 90 fps) as far as 14 meters with unprecedented efficiency. This interface is well suited for applications where the MIPI CSI-2 (D-PHY) length restrictions are not sufficient, while at the same time, a highly durable cable with low power consumption and low cost are essential. Camera developers can use the flexible FRAMOS Sensor Module Ecosystem to validate a variety of image sensors in the lab and in the field while taking advantage of the interface’s features.
-
product
4 MP OV4682 RGB IR Camera Module
e-CAM40_CUMI4682_MOD
The e-CAM40_CUMI4682_MOD is a 4 MP RAW RGB-IR MIPI OV4682 camera module with the M12 S-mount lens holder. The e-CAM40_CUMI4682_MOD RGB IR camera module is based on OmniVision's OV4682 1/3" Optical format CMOS Image sensor, that captures high-resolution images and videos as well as IR information. Its dual RGB-IR Camera capabilities allow it to bring a host of additional features to machine vision applications and by combining RGB - IR in a single camera module reduces the total cost and saves space. Customers can evaluate e-CAM40_CUMI4682_MOD with See3CAM_CU40 over USB 3.0 interface and e-CAM40_CUTK1 over MIPI interface. e-CAM40_CUMI4682_MOD camera module can stream the 4MP(2688x1520) unprocessed 10-bit RAW data video upto 40 fps. Also read OV4682 RGB IR camera module frequently asked questions.
-
product
Low Power MIPI Bridging Solution With Integrated Flash
CrossLinkPlus
*Instant-on (< 10 ms) configuration with integrated flash memory*Integrated flash enables flexible reprogramming in the field*Two 4-lane MIPI D-PHY transceivers at 6 Gbps per port*11 programmable, source synchronous I/O pairs for camera and display interfacing*Available in small 3.5 mm x 3.5 mm BGA package with 0.4 mm pitch*Comprehensive library of IP and reference designs, compatible with CrossLink
-
product
Open Standard Module (OSM)
ROM-2820
Advantech ROM-2820 OSM 1.1 Computer-on-Module is powered by NXP i.MX 93 SoC which includes Cortex-A55 Dual-core in combination with one Cortex-M33 real time processor, Ethos®-U65 Neural Processing Unit (NPU) and 2D graphics engine. It provides USB2.0, Gigabit Ethernet, MIPI-CSI, I2C, SPI, GPIO, CAN-FD and MIPI DSI display for embedded applications
-
product
Carrier Boards
ROM-DB5901
ROM-DB5901 is an evaluation carrier board designed for the Advantech SMARC v2.0 module. It is compatible with the ROM-5720, ROM-5620 and ROM-5721 SMARC modules and has a multiple I/O interface for evaluation and development. It supports wide range operating temperatures, two power input interfaces, and two MIPI connectors for the camera module. ROM-DB5901 is an ideal development board for mobile applications, such as portable devices, industrial tablets or HMI systems
-
product
MIPI Receiver Test Solution
M8085A
The M8085A is a software plug-in for M8070A Bit Error Ratio Test system software within the M8000 series of BER test solutions. The M8085A software plug-in controls either the M8190A or the M8195A Arbitrary Waveform Generators to create C-PHY or D-PHY standard compliant test signals. In addition it provides routines for calibration of all signal parameters and for all tests specified in the applicable Conformance Test Suite. Together with the additional available DUT control interface it is possible to read the BER of the receiver under test from the M8070A software and display the BER dependency from test parameters within the M8070A user interface.
-
product
3.4 MP Google Coral Camera
E-CAM30_CUCRL
e-CAM30_CUCRL is a 3.4 MP 4 lane MIPI CSI-2 custom lens camera board for Google Coral development board. This Google coral camera is based on 1/3" inch AR0330 CMOS Image sensor from ON Semiconductor® with 2.2 µm pixel.
-
product
5.0 MP NVIDIA® Jetson Nano™ Camera
E-CAM50_CUNANO
e-CAM50_CUNANO is a 5.0 MP 2-lane MIPI CSI-2 fixed focus color camera for NVIDIA® Jetson Nano™ developer Kit. This camera is based on 1/2.5" AR0521 CMOS Image sensor from ON Semiconductor® with built-in Image Signal Processor (ISP). This powerful ISP helps to brings out the best image quality from the sensor and making it ideal for next generation of AI devices.
-
product
MIPI
The MIPI Alliance creates and promotes specifications for the Mobile and Mobile-Influenced markets. These specifications enable and software interfaces that simplify the integration of components built into a device, from the antenna and modem to peripherals and the application processor.
-
product
SPMI Protocol Analyzer and Exerciser
PGY-SPMI-EX-PD
Prodigy Technovations Pvt. Ltd.
SPMI Protocol Analyzer (PGY-SPMI-EX-PD) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. SPMI (System Power Management Interface) is a MIPI (Mobile Industry Processor Interface) standard with 2-wire synchronous serial, bidirectional interface that connects the integrated Power Controller(PC) of a System on- Chip (SoC) processor system with one or more Power Management Integrated Circuits (PMIC) voltage regulation systems.
-
product
Embedded Vision And Processing FPGA
CrossLink-NX
*Instant-on configuration – IO configures in 3 ms, and device as fast as 8 ms*Two hardened 4-lane MIPI D-PHY transceivers at 10 Gbps per PHY / 2.5 Gbps per lane*Up to 37 programmable source synchronous I/O pairs for camera and display interfacing
-
product
5MP OV5640 MIPI Camera Module (70mm Flex Cable)
e-CAM57_MI5640_MOD
e-CAM57_MI5640_MOD is a Omnivision camera module (MIPI) with 70mm Flex Cable featuring OV5640 image sensor. This OV5640 camera module streams HD @ 60fps, Full HD @ 30fps & 5MP @15fps. Any processor system like i.MX6, OMAP4430, OMAP4460, that has a MIPI CSI-2 can directly interface the e-CAM57_MI5640_MOD. Check out the other 5MP OV5640 MIPI camera module with 20mm flex cable - e-CAM52A_MI5640_MOD. Customization of flex cable length is possible.
-
product
5MP MIPI Camera Module
E-CAM55_CUMI0521_MOD
e-CAM55_CUMI0521_MOD is a small form factor, 5 MP fixed focus camera module based on AR0521 CMOS image sensor from ON Semiconductor® has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs all the Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images and video. This low light camera module can stream uncompressed VGA (640 x 480) at 75 fps, HD (1280 x 720) at 100 fps, 1280 x 960 at 75 fps, FHD (1920 x 1080) at 65 fps, 2560 x 1440 at 38fps, 2592 x 1944 at 28 fps.
