EM Simulation
models and predicts the character of electromagnetic fields. Electromagnetic Field
See Also: Electromagnetic Radiation, Electromagnetic Simulation, EM Simulators
-
Product
Avionics Test & Simulation Software
-
Ballard CoPilot® is an intuitive, graphical software program that allows you to easily monitor, record, replay, analyze, and simulate avionics bus data. With CoPilot you can interact directly with data on multiple buses using Ballard avionics interface hardware or work with previously recorded data. This advanced program features powerful tools for development, testing, troubleshooting and maintenance of avionics equipment and systems.
-
Product
CAN & LIN bus Custom Test & Simulation Software
CanX
-
Schleissheimer Soft- und Hardwareentwicklung GmbH
CanX is the custom testing and simulation software for CAN and LIN bus for specific user groups. The run-time software is designed to execute predefined or automated tasks in testing, work preparation, production, repair or project management.
-
Product
Basic Rate and Primary Rate Simulator
emutel Pro
-
Emutel Pro has the same features as the Emutel but has 2 BRI and 2 PRI which will allow you to test both basic rate or primary rate equipment or basic to primary links to be set up. Emutel Pro has optional network support and protocol analysis.
-
Product
4 Port T1/E1/PRI ISDN Simulator
SIM-4PRI
-
The most inexpensive ISDN simulator on the market. This unit has four PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
Ray tracing and Laser Simulation / Cavity Design Software
LasEasy V1.0
-
LasEasy software is the professional software for simulating and designing solid-state laser cavity, optical amplifier system, and parametric OPO systems. It can also simulate the laser light propagation in both horizontal and vertical (sangital and tangitial) planes.
-
Product
Fast Transient Burst Simulators
FNS Series
-
A simulator to reproduce fast repetitive high frequency pulses which are generated when switching ON/OFF electric current on the inductive load. International Standard IEC 61000-4-4 defines immunity tests for power supply lines or I/O signal lines against fast transient repetitive bursts. Also adopted as a Japan Industrial Standard.
-
Product
Fibre Channel Test & Simulation Interface for PCI-X
PCI-X-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
Voltage Variation Simulator
KES7400A
-
The KES7400A Series comes in a single cabinet that consists of a Signal Generator module (including an arbitrary pulse generator), which combines our power supply technology and EMC technology, and a high-speed bipolar power supply module. Many automotive electronic devices have long wire harnesses and inductive load characteristics, as do motors, or capacitive load characteristics with a large-capacity capacitor connected between the input and ground. In the case of these devices, general DC power supplies exceed the linear operation range, potentially making it impossible to obtain the desired waveform output.
-
Product
2-CH MIL-STD-1553A/B Bus Simulator Module
1553 WA73A-455
-
The WA73A-455 MIL-STD-1553A/B Bus Simulator Module allows a system controller in an ATE system to communicate with and test devices that conform to the MIL-STD1553A/B data bus used in military aircraft and communications systems. Each of the WA73A-455's two channels operate as two separate and independent channels with their own VXIbus logical address, interrupts, and complete set of controls and indicators. As a result, each channel of the WA73A-455 is truly an independent instrument, and, therefore, individually programmable.
-
Product
2 PRI + 16 BRI-U ISDN Simulator
CH-16BRI-U-MOD-2PRI
-
This unit has two PRI ports and 16 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
Product
AC drives, Soft-Starters or Servo Drives Simulation Software
-
Product simulation software enables users to operate, program and simulate AC drives, Soft-Starters or Servo Drives directly from their computer without having the actual product present or connected. Our simulation software can be used as a demonstration tool during a sales meeting or as an interactive tool for training classes. Software available In addition we offer simulation software for dedicated markets such as pumping, mining, material handling, etc... to demonstrate the use of motor controls in simulated applications.
-
Product
4 Port BRI-S/T ISDN Simulator
BRI-4ST
-
The unit has four S/T ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
Product
24 Channel Isolated Counter / Totalizer & 16 Channel Pulse Simulator
DP-cPCI-5004
-
DP-cPCI-5004, Isolated Pulse Simulator / Counter / Totalizer module is an integrated module for pulse output, pulse measurement and event counting. The module has 16 isolated channels of pulse output at desired frequency. The 16 channels are divided into three groups . The first two groups have four differential and one single ended channels each.
-
Product
Simulation Models for Passive Components, Transistors, Diodes, etc.
-
An indispensable collection of the industry''s most advanced simulation models for passive components, transistors, diodes and more. These reliable, measurement-based models maximize the RF/MW electronic design automation (EDA) process, reduce design cycle times, and lower product development cost. With a few EASY steps, the Modelithics Model Libraries are ready to use in EDA tools.
-
Product
VXI Synchro/Resolver Simulation & Measurement
65CS4
-
NAI’s 65CS4 is a Synchro/Resolver Simulation & Measurement Instrument on a single-slot VXI board. The board incorporates up to four Synchro/Resolver measurement channels and up to four instrument-grade Synchro/Resolver simulation channels, or up to eight embedded grade Synchro/Resolver simulation channels that can be used independently and/or simultaneously.
-
Product
Motion Simulator For Test Systems
Metis
-
METIS is a motion simulator for sensor and end system level testing. Configurable design allows you to create system you need! - 1-axis rate table for gyro testing - 2-axis unit for 6DOF accelerometer and gyroscope testing - 3-axis Gimbal system for simultaneus Yaw, Pitch and Roll stimulus.
-
Product
Hybrid Vehicle Battery Simulator and Test System
-
Winner of the SAE 2008 Technical Award for Hybrid Vehicle Testing Technology, SAKOR Technologies Hybrid Vehicle Battery Simulator and Test System is designed for simulating high-voltage batteries in an electric drivetrain testing environment as well as directly testing high-voltage batteries and charging systems.
-
Product
Engine Simulator
MS 1118
-
Test Set-A calibration unit is a test jig is used to simulate parameters of Adour 804E and 811 engines of Jaguar aircrafts. It simulates current, voltage, speed, and turbine gas temperature. It performs NL Check, NH Check, TGT1 (Non T2 Compensated), TGT2 (T2 Compensated), Amp (Non T2 Compensated), Amp (T2 Compensated), Solenoid Volt, TGT Inject, NL Inject, and NL/TGT Redatum.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, 750 V Isolation
43-752A-001
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Laser Source Simulator
MT1888 Series
-
The MT1888 products are state-of-the-art Laser Source/Spot Simulators (LSS) used for the testing of laser guided munitions such as the Hellfire & Hellfire II missiles, Paveway, and the AGM-65E Laser Maverick missile.
-
Product
Multi-Protocol Test & Simulation Adapter for USB or Ethernet
EXC-UNET2/xx
-
The EXC-UNET2/xx is a multi-protocol test and simulation adapter for USB or Ethernet equipped computers. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of a number of communications protocols, both in the lab and in the field.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, Simplified Current Sink, 750 V Isolation
43-752A-903
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
ISA Bus Dual Redundant MIL-STD-1553 A/B Simulator / Analyzer / Tester
CIC101-4
-
Price: Request QuoteMIL-STD-1553 A, B Simulator/Analyzer/Tester ISA BUS Interface Card. The CIC101 can be used for Validation Testing,Production Testing, full bus simulation and monitoring, as ageneral purpose 1553 interface or a stand alone bus Analyzer. It provides precise message scheduling andmeasurements. Major and minor frame times areindependent of message sequences or retransmissions onerrors. The start of all command messages may be set to beindependent of message length, response time or length ofresponse. The CIC101 features a calibrated Message timingand low jitter RT responses.
-
Product
PXI/PXIe LVDT/RVDT/High Speed Resolver Simulator Module, 4-Banks
43-670-301-AABBCC
-
The 41-670-301 (PXI) and 43-670-301 (PXIe) are ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types, as well as resolvers with high speed simulation up to 130krpm rotation. They have four banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 4 channels of 5 or 6-wire or 8 channels of 4-wire.
-
Product
4, 8, 16 And 32 ChannelARINC429 Test And Simulation Modulefor PCI Express
APE429-x
-
ARINC429 Test and Simulation modules with 4, 8, 16 or 32 Software programmable Tx/Rx channels plus up to 8 Discrete I/O’s. The APE429-x is a functional replacement for the models API429-x/APX429-x.
-
Product
Mobile Comm DC Source w/ Battery Emulation, DVM
66321D
-
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66321D mobile communications dc source provides fast transient response, exceptional sourcing, output resistance programming, and precision measurement. This product is specially designed for testing next generation digital wireless communications products. The 66321D mobile communications dc source offers a new capability that simulates the internal resistance of a battery or battery pack. Additionally, these high performance models offer improved transient response and stable output operation with either short or long load leads. The 66321D dc source provides all of the capabilities of the 66321B with the addition of a built-in digital voltmeter.
-
Product
Troubleshooting Track Circuit Simulators
14900 Series
-
The 14900 seriesTrack Simulator features a front panel with standard set up resistors and terminals and electrically conductive model track to simulate a track circuit suitable for instructional and hands-on training purposes. A locked drawer provides additional switches, potentiometers, and controls that allow selective implementation of many faults commonly found in typical track circuits.
-
Product
MIMIC® Web Simulator
-
MIMIC Web Simulator creates a virtual lab with hundreds of simulated web servers. It allows you to easily develop and test your web clients, management and monitoring products. Having a virtual and scalable environment, you can try variety of scenarios to test your applications to assure your customers that your web services will work properly when deployed across heterogeneous environments. Best of all, you can reduce your lab budget significantly.
-
Product
Acceleration Simulation Mode Roller Set for Vehicles with a Single Driven Axle
ASM-BF/1 | VP 230043
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-BF/1 roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97.
-
Product
STANAG3910/EFEX Test And Simulation Module for Standard Ethernet
ANET3910
-
STANAG3910/EFEX Test and Simulation module for Standard Ethernet. The ANET embedded Linux Operating System gives the unique capability to run the optional PBA.pro Engine right in the box. Another option is the ANET-ADK onboard software development kit where users create run-time applications (e.g. STANAG3910/EFEX to Ethernet Converter, STANAG3910/EFEX to Ethernet Gateway) to execute right in the box. For wireless applications, an ANET compatible USB Wifi dongle is optionally available.The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
