EM
-
Product
Antenna, Omni-Directional Wideband Discone
EM-6105-1 | 30 MHz – 3 GHz
-
Electro-Metrics EM-6105-1 is a broad-band vertical co-linear array. It provides very wide frequency range omni-directional coverage in a single package. The antenna collapses for convenient storage and transport.
-
Product
Antenna, Loop
EM-6871 | 30 Hz – 1 MHz
-
The EM-6871 Antenna can be used with any 50 ohm /Receiver/Field Strength Meter to obtain magnetic field measurements from 30 Hz to 1 MHz.
-
Product
Antenna, High Field Biconical
EM-6913 | 20 MHz – 300 MHz
-
The Electro-Metrics EM-6913 can be used for generating high intensity fields as required for EMC immunity testing 20 MHz to 300 MHz.
-
Product
Antenna, Octave Band Horn
EM-7021 | 2 GHz – 5 GHz
-
Electro-Metrics offers three horn antennas, each covering an octave bandwidth from 1 to 10 GHz. The horns are individually calibrated and can be used for either receiving or transmitting applications. They are especially suited to radiated immunity testing and can be used to generate fields in excess of 200 Volts/meter. All three horns feature type “N” connectors and exhibit low VSWR to ensure compatibility with power amplifiers.
-
Product
Compact EMC Test Chamber
EMC-3C
-
This compact 3 meter test range will settle into test areas of limited space while continuing to produce exceptional performance for EMC measurement. Emission quiet zones of up to 1.5m are accommodated with very repeatable results. Suitable for EMC pre-compliance emissions and compliant immunity testing.
-
Product
Antenna, Octave Band Horn
EM-7022 | 4 GHz – 10 GHz
-
Electro-Metrics offers three horn antennas, each covering an octave bandwidth from 1 to 10 GHz. The horns are individually calibrated and can be used for either receiving or transmitting applications. They are especially suited to radiated immunity testing and can be used to generate fields in excess of 200 Volts/meter. All three horns feature type “N” connectors and exhibit low VSWR to ensure compatibility with power amplifiers.
-
Product
Antenna, Wideband Discone
EM-6115 | 10 KHz – 2 GHz
-
The EM-6115 is a broad band collinear array allowing very wide Omni-Directional frequency coverage in a single package. Below approximately 100 MHz, the EM-6115 acts as an active vertical rod which offers 10 to 12 dB Greater unsaturated instantaneous dynamic range than competitive antennas (overload field strength: 2 V/meter) which greatly reduces intermodulation generated signals in a typical read world RF environment. In the congested spectrum above 100 MHz the antenna is passive and contributes no intermodulation products so the overload point is determined solely by the receiving instrument. This immunity to overload can often make the difference between useful signal output and an indecipherable jumble of spurious products and is accomplished without compromising sensitivity. The antenna collapses for convenient storage and transport.
-
Product
Antenna, Omni Directional Wideband
EM-6851 | 2 GHz – 18 GHz
-
The EM-6851 Omni-Directional Wideband Antenna is capable of operating as either a transmitting or receiving antenna over the 2 to 18 GHz frequency range. This antenna provides a 45% size reduction when compared to similarly performing models. The antenna is enclosed in a weather resistant radome. The length of the support rod allows a microwave amplifier to be connected directly to the output connector, reducing the potential signal loss compared to an amplifier connected at a more distant point.
-
Product
Antenna, Log Periodic
EM-6956-1 | 1 GHz – 2.5 GHz
-
The Electro-Metrics EM-6956-1 Log Periodic Antenna operates over the 1 to 2.5 GHz frequency to range.
-
Product
Antenna, Loop
EM-6879 | 10 KHz – 30 MHz
-
The EM-6879 Loop Antenna is used for magnetic field measurements over the frequency range of 10 kHz to 30 MHz. The EM-6879 is designed for use with any 50 ohm Receiver System. The antenna has a balanced Faraday shield that reduces its response to electric fields to a vanishingly small amount so that it can produce a practically pure magnetic field response.
-
Product
Antenna, Log Periodic
EM-6936 | 700 MHz – 1300 MHz
-
The Electro-Metrics EM-6936 Log Periodic Antenna operates over the 700 MHz – 1300 MHz frequency range.
-
Product
Antenna, Log Periodic
EM-6954 | 70 MHz – 1 GHz
-
The EM-6954 is designed to meet antenna requirements for both field strength measurement and radiated susceptibility in the 70 MHz to 1 GHz frequency range.
-
Product
Antenna, Loop
EM-6874 | 20 Hz – 30 MHz
-
The EM-6874 Loop antenna is nominally used 20 Hz to 30 MHz and is designed for uncalibrated substitution measurements of shielding effectiveness as described by MILSTD-285, IEEE STD 299, and NSA-65-6.
-
Product
Antenna, Octave Band Horn
EM-7020 | 1 GHz – 2.5 GHz
-
Electro-Metrics offers three horn antennas, each covering an octave bandwidth from 1 to 10 GHz. The horns are individually calibrated and can be used for either receiving or transmitting applications. They are especially suited to radiated immunity testing and can be used to generate fields in excess of 200 Volts/meter. All three horns feature type “N” connectors and exhibit low VSWR to ensure compatibility with power amplifiers.
-
Product
Antenna, Omni-Directional Wideband
EM-6865A | 2 GHz – 18 GHz
-
The EM-6865A Omni-Directional Wideband Antenna is capable of operating as either a transmitting or receiving antenna over the 2 to 18 GHz frequency range. The antenna is enclosed in a weather resistant radome, and is a ruggedized version of EM-6865. The redesigned mounting fixture provides an easy means to mount to roof-racks or other rails or surfaces.
-
-
Product
Spiral Antenna
-
UHF Spiral antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in the monitored asset. It is a broadband antenna with a flat response which makes Spiral antenna suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain.
-
Product
Probes, Clamp-On
EM-6987 | 1 KHz – 110 MHz
-
The EM-6987 is capable of measuring signals and noise superimposed on power currents up to 300 A from DC to 400 Hz. Intermodulation effects on current probe output are also negligible.
-
Product
Antenna, Tactical, Log Periodic
EM-6942 | 400 MHz – 4 GHz
-
The EM-6942 is designed for harsh environmental conditions and its folding elements and 2-section design simplifies transport and storage. The antenna can be mounted on a tripod or any ¼-20 mount and be positioned for horizontal or vertical polarization.
-
Product
Antenna, Log Periodic
EM-6946 | 300 MHz – 3 GHz
-
The EM-6946 offers an exceptional combination of frequency coverage of 300 MHz –3 GHz and high power handling capability without compromising the consistent performance versus frequency that makes the log periodic antenna so desirable for test applications.
-
Product
Omni-Directional Antenna
EM-6116 | 2 GHz – 10 GHz
-
The EM-6116 is a vertically polarized, omnidirectional antenna covering the frequency range 2 to 10 GHz. It is enclosed in a weather resistant radome. Smaller than other similar antennas, the EM-6116 is ideal for covert applications.
-
Product
Antenna, Ultra-Wideband, Directional
EM-6945 | 500 MHz – 25 GHz
-
The EM-6945 Vector Log Periodic antenna covers the broadest frequency range available in such a small, rugged, deployable package. Offering the uncompromising performance you’ve come to expect from Electro-Metrics, a state-of-the-art design provides the antenna characteristics you need, unmatched by others in the community.
-
-
Product
Omni-Directional Antenna
EM-6104-1 | 20 MHz-18 GHz
-
The EM-6104-1 is an omni-directional, dual band, hybrid antenna covering 20 MHz-18 GHz. The antenna features wide frequency coverage making it an excellent choice for a variety of applications such as general purpose measurements as well as wideband security applications. This lightweight antenna is ideal for deployable applications that require wideband coverage in a very small footprint. The antenna’s elements collapse for convenient storage and transport. The antenna is configured to mount on a standard ¼-20 tripod stud. The EM-6104-1 Omni-Directional antenna is supplied with an EM-6089 Battery Pack.
-
Product
Earth Meter
EM-4055
-
The EM-4055 Earth Meter is a digital, microprocessor-controlled instrument that allows to measure the earth resistance and ground resistivity (using Wenner´s method), as well as to detect parasitic voltages present in the ground. This instrument is well suitable to measure earth systems in power substations, industries, distribution networks, etc., according to VDE 0413. It is also suitable for soil resistivity measurements, in order to optimize the earth systems project
-
Product
Probes, Magnetic Field
EM-6880 | 9 KHz – 520 KHz
-
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
-
Product
Probes, Clamp-On
EM-6980 | 20 Hz – 50 KHz
-
Current probes enable you to measure conducted current without direct connection to the circuit under test by clamping around the conductor, current carrying wire or structural member being tested.
-
Product
Cryo-Correlative Microscopy Stage
CMS196
-
Linkham Scientific Instruments
Electron microscopy (EM) provides structural information at very high resolution. However, it can give only restricted insight into biological and chemical processes due to limitations in staining and sample preparation processes. Fluorescence microscopy on the other hand is a very sensitive method to detect biological, chemical and genetic processes and events inside living cells. Cryo-CLEM brings it all together: it is a new and emerging technique to combine the individual advantages from both Fluorescence and EM by imaging the same sample location with both techniques and superimposing the complementing information.
-
Product
Standard Electromagnetic Vibrator
KD-9363-EM
-
King Design Industrial Co., Ltd.
The purpose of vibration testing is to make a series of controllable vibration simulation in lab, no matter generated by natural or man-made vibration environment; such as waves, tidal flaps, wind, earthquake or rain and so on. It is to test if the product is capable of sustaining the vibration environment exerted from transporting or usage along its effective life cycle; and certify the standard of design & functional requirement of product. The value of vibration testing is to confirm the reliability of products and effectively screen out the bad products in factory; avoiding damages occurred at arrival; and to assess the failure analysis on the non-performing products; expecting to reach a high standard, high-reliability products. The vibration test stresses on the continuity and fatigue; and contributes to the understanding of product’s status under vibration circumstance in a normal environment; and avoids the product’s unpredictable damage caused under certain vibrating frequency for a long time.
-
Product
Transmissive Optical Encoder Module
EM1
-
The EM1 is a transmissive optical encoder module designed to be an improved replacement for the Avago HEDS-9000 series encoder module. This module is designed to detect rotary or linear position when used together with a code wheel or linear strip. The EM1 consists of a lensed LED source and a monolithic detector IC enclosed in a small polymer package. The EM1 uses phased array detector technology to provide superior performance and greater tolerances over traditional aperture mask type encoders.
