Electric Vehicle Test Systems
See Also: EV Test Systems, Electric Vehicle
-
Product
Compliance Test Systems
LMG Test Suite
-
ZES ZIMMER Electronic Systems GmbH
The ZES ZIMMER test system LMG Test Suite tests in accordance with the currently valid version of EN 61000-3-2/-12 or EN 61000-3-3/-11 and also supports measurements per ECE R-10.4 Annex 11 (e.g. electromagnetic compatibility of vehicles). As a manufacturer of precision power measurement technology, we are represented on the international standards committee. As a result, changes in standards are immediately incorporated into our test systems.
-
-
Product
Battery PACK (500v-1000v)Test System
-
Shenzhen Sinexcel RE Equipment CO., Ltd
PACK test equipment adopts sinexcel, firstly adopts three-level AC scheme, and the detection process supports multi-gear switching. The device integrates voltage, temperature, pressure and other auxiliary channels, and CAN also integrate various communication protocols such as temperature box, water cooler, mainstream CAN CANFD 485, etc. It supports a variety of practical and innovative functions such as data one-click automatic export, which meets all aspects of PACK battery electrical performance testing.
-
Product
Automatic Test System
Star-Rec
-
Test entire HDI panel at once, or step & repeat in the "feed" direction. Fastest BGA Strip test system available. Star-Rec comes standard with: * loader * board cleaner * CCD Camera Alignment * electrical test section * fail and pass re-stackers * Board Marker
-
Product
Stator Test Systems
-
Automation Technology's STS-3800 has become the "gold standard" in Stator Testing Equipment. The STS-3800 is packed with standard features and like all of ATI's 3800 Series Test Systems, it is backed by the industry leading two-year limited warranty. The STS-3800 offers the most comprehensive testing of stators and fields available.
-
Product
High Current Test System
-
HIGHVOLT Prüftechnik Dresden GmbH
High current test systems are used to test the thermal stability of equipment and components. The test system induces a current in the test object causing it to heat up. Therefore, the test object is designed as a shorted circuit. The high current test system measures the temperature of the test object at various points, in addition to the current. As a special feature, the temperature that the test object should reach can be specified and the amount of the current can be automatically calculated by the HIGHVOLT test system.
-
Product
Electricity Metering Device- Residential
ES-12B
-
Designed for the residential smart meter rollout in Great Britain, this 5 terminal single phase electricity meter is an addition to our range of SMETS2 compliant solutions.With two 100A main disconnect relays, dedicated secure microcontroller and multiple communications interfaces including Zigbee and DLMS, the ES-12B is accurate and can operate in prepayment mode.
-
Product
Electrical Heat Shrink Tubing Solutions
-
TE Connectivity produces Raychem Electrical heat shrink tubing that sets extremely high standards in areas such as insulation, protection, and element proofing. Raychem shrink tubing uses a duplication process that involves a cross-linked material design ensuring cable system's performance. This cross-linked design creates an impenetrable barrier from the elements while simultaneously binding cables and insulating them. The heat shrink process involves tubing that utilizes a thermal influence that causes it to tightly shrink and adhere to a cable. This tight seal is not only ultra-protective, but also flexible, abrasion resistant, and easy to use. This flexible tubing can fit a huge range of cable sizes and specifications. Perfect for various different operations and industrial applications. This includes cables, wires, and even joints.
-
Product
Electricity Metering Device
Mk7B
-
Designed for residential and commercial use, the Mk7B can operate in credit or prepayment mode. It has a 100 Amp relay for remote connect/disconnect of electrical services.
-
Product
Angle Measurement Devices for Vehicles
ANGLE MEASUREMENT IN VEHICLES
-
F. W. Breithaupt & Sohn GmbH & Co.KG
*Development, manufacture according to customer inquiries*Many decades experience in project managment and solutions for special vehicle devices*Mechanical and mechatronical solutions*Made in Germany
-
Product
The All-In-One Noise Test System
NXA Series
-
Noise eXtended Technologies S.A.S.
The NXA is a fully automated Phase Noise analyzer. Its dual channel architecture allows the system to use a cross-correlation process to cancel its internal noise floor. This reliable technique provides access to the unique noise floor performance of the DCNTS.
-
Product
X-ray Non-Destructive Testing (NDT) System
DynamIx HR / Series 5
-
High precision 12-bit 50µm reading allows inspection of minute image details. Wide dynamic range resulting in wide allowance of X-ray exposure value.
-
Product
Multifunctional Electrical Installation Parameter Meter
AMPI-540
-
Much more than a multi-function meter*the largest 7" touch panel on the market - outstanding ergonomics and ease of use*removable microSD card - easy increase of memory capacity*lithium-ion battery - longer meter operation*possibility to add a voice memo or a photo to the measurement - multimedia description of the measurement site*
-
Product
IEC60335-1 Electrical Inclined Plane Device
CX-100
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-1 Electrical Inclined Plane Device is designed and manufactured in accordance with IEC60335-1 clause 20.1. The IEC60335-1 Electrical Inclined Plane Device is to determine the stability of electric appliances which are used on a table or on the floor. The IEC60335-1 Electrical Inclined Plane Device consists of a surface and an angle adjusting device, with angles 0~15° adjustable.
-
Product
Shock Test System, Battery Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's shock test system used to measure and determine the impact resistance of a product or package. It is mainly used to evaluate the reliability of the function and the integrity of the structure of the test product under impact environment. Suitable for impact testing of aerospace, aerospace, marine, military, consumer electronics, automotive, household appliances and display equipment.
-
Product
Test Systems
-
Computer Gesteuerte Systeme GmbH
The system is pin and software compatible to the larger test systems LB302 / 303. Due to the fewer needed I/Os, the tester features the compact G6 receiver (Virginia Panel Cooperation) compared to the larger G12 of the other tester versions. The LB301 is equipped with a 2kW power supply and can control one load box.
-
Product
Vehicle Presence and Data Collection Sensor
TrafiCam x-stream
-
TrafiCam x-stream combines a CMOS camera and video detector in one unit. TrafiCam x-stream sensors detect and monitor moving and stationary vehicles at signalized intersections and collect traffic data at intersections or interurban roads. Via detection outputs or via IP protocol, vehicle presence information is transmitted to the traffic controller so that signal timing can be adjusted dynamically. TrafiCam x-stream offers streaming video at full frame rate, to be used for traffic monitoring in a control room.
-
Product
Test System
Tessy
-
TESSY automates the whole unit test cycle including regression testing for your embedded software in C/C++ on different target systems. As an easy-to-install and easy to operate testing tool TESSY guides you through the unit test workflow from the project setup through the test design and execution to the result analysis and reporting. TESSY takes additionally care of the complete test organization as well as the test management, including requirements, coverage measurement, and traceability.
-
Product
Primary Injection Test Systems
-
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
Product
Modular Breakout System 8-Pin Power D-type Plugin Module for 40-192
95-192-001
Modular Breakout System
The 95-192-001 Plugin Breakout Module is designed to be fitted to a PXI 40-192 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
Product
Production – High Speed Functional Test Systems
-
Chroma Systems Solutions, Inc.
Built for production, our high speed functional automated test system is based on our C8000 platform which uses a unique test command optimization technology to prevent sending repetitive control commands to the system hardware devices. This improves system test speed dramatically and, when used with our PowerPro III software, makes it highly efficient as a closed or optimized auto test system.
-
Product
Ionic Contamination Test Systems
CM+ Series
-
The Contaminometer (CM+ Series) system was originally developed by Protonique, the business of industry guru Brian Ellis. They also featured in the early development programmes of "cleanliness measurement" carried out by the US Department of Defense at China Lake in the 1970s. Historically, International Standard IPC-J-STD001 stated that assemblies be cleaned to a value of <1.5µg/cm2 of NaCl equivalence. However, the new design is linked to the introduction of the new process control metric introduced by Gen3 Systems: Process Ionic Contamination Testing. The CM+ Series measure the amount of ionic contamination in accordance with all existing test methods, often referred to as ROSE testing, as well as the new PICT test.
-
Product
Dayton Audio Test System
DATS V2
-
Highly accurate measurement of loudspeaker impedance and T/S parametersEasy-to-use, fully-featured measurement software with intuitive interfaceCompact USB measurement module with molded test leads and alligator clipsSoftware includes signal generator, scope, and measurement of inductors and capacitorsData can be saved to create a driver parameter library or exported to popular box design programsNew V2 hardware and software simplify setup and eliminate warm-up/cool-down times
-
Product
PCB Interconnect Stress Test System
-
PWB Interconnect Solutions Inc.
Integrated package including PC, Software with real time graphing and all related systems and hardware for 8 head, dual sense testing model IST-HC
-
Product
Electric Vehicle Battery Cell Tester
MCV
-
The MCV is a low-current life cycle test system for development of primary and rechargeable batteries in various chemistries. Operating from a common microprocessor, multiple circuits in the MCV module can run individual test programs. Additionally, the MCV is designed and built for ease of maintenance and service. The modular construction means that most subassemblies, large or small, remove easily for service outside the cabinet and fast replacement.
-
Product
Small Device Noise Emission Test System
-
The Small Device Noise Emission Test System from VIacoustics is a turnkey solution for the measurement of noise emissions of small devices typically used in computers, consumer electronics, appliances and automobiles. The system includes all hardware and software necessary (see the components tab) for the determinations of sound power levels (1/3 octave band and A-weighted), emission sound pressure levels (normalized 1/3 OB, A-weighted and high resolution FFT) and *ISO 532B loudness. The system is designed to be operated by a technician for production level testing or to be used by an engineer in the product development process.
-
Product
200KHz AUTOMATIC TRANSFORMER TEST SYSTEM
VE2729XAU
-
Its a Microprocessor Based 200KHz Automatic Transformer Tester with inbuilt 20 Pin Channel Scanner for Automatic Switching and Testing Coils & Transformers (Ferrite) with Max. 20 PINS. Test Parameters : -> Inductance (L)-> Leakage Inductance (Lk)-> Capacitance (C)-> DC Resistance (Rdc)-> AC Resistance (Rac)-> Turns Ratio with Winding Polaity-> Quality Factor (Q)-> Impedance (Z)
-
Product
Additional hardware for our test systems
-
REINHARDT System- und Messelectronic GmbH
Our test systems are made up of modules which can be added to the needs of our customers.
-
Product
Series and EOL Testing of Electric Motors
-
Highly automated EOL test system for blind motors*Test station with fully automatic mechanical and electrical contacting *Scanning the product coding with barcode scanner*Integrated label printing, additional error printer*Contact protection by light curtain
-
Product
Thermal and Mechanical Testing System
3500 System
-
The Gleeble 3500 is a fully integrated digital closed loop control thermal and mechanical testing system. Easy-to-use Windows based computer software, combined with an array of powerful processors, provides an extremely user-friendly interface to create, run and analyze data.
