Battery Simulation
reproduce battery performance under test conditions.
See Also: Battery Simulators
-
Product
Automatic Battery
BATLV480
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
Product
Fixed Batteries (Constant Function)
-
Lifasa - International Capacitors, SA
Fixed compensation equipment has different variants depending on the type of enclosure / support and the configuration of the equipment (type of capacitor).
-
Product
4 Port T1/E1/PRI ISDN Simulator
SIM-4PRI
-
The most inexpensive ISDN simulator on the market. This unit has four PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
Standard 0.87 (24.70) - 5.40 (153.00) Battery Probe
BIP-12
Battery Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 30Resistance Remark: Probe Resistance Steel: 30 mOhms, Gold plated: 100 mOhmsTest Center (mil): 260Test Center (mm): 6.60Full Travel (mil): 394Full Travel (mm): 10.00Recommended Travel (mil): 315Recommended Travel (mm): 8.00Overall Length (mil): 1,220Overall Length (mm): 31.00
-
Product
SLA battery charger
SBSC11Q
-
The SBSC11Q is a battery charger designed to simultaneously charge up to four SBSC11 sealed lead acid batteries or other SBS type batteries having a nominal voltage of 12.0V
-
Product
Grid Simulator
PAS-F
-
The Intepro PAS-F Series is a broad line of programmable three phase output regenerative utility grid simulator products. With power levels ranging from 45kVA up to 1.6MVA, the series is capable of testing the largest of dispersed energy inverters. The PAS-F combines utility grid simulation with regenerative bi-directional AC source controlled power that is capable to both source and sink full current from the equipment under test (EUT).
-
Product
PXI 16 Channel Switch Simulation Module
40-480-121
Switch Simulation Module
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
Product
Standard 1.10 (31.00) - 3.85 (109.00) Battery Probe
BIP-2
Battery Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 30Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 50Full Travel (mm): 1.27Recommended Travel (mil): 50Recommended Travel (mm): 1.27Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 365Overall Length (mm): 9.27
-
Product
Transistor-Level Defect Simulator
Tessent DefectSim
-
Tessent DefectSim is a transistor-level defect simulator for analog, mixed-signal (AMS), and non-scan digital circuits. It measures defect coverage and defect tolerance. Tessent DefectSim is perfect for both high-volume and high-reliability ICs. Tessent DefectSim replaces manual test coverage assessment in AMS circuits needed to meet quality standards such as ISO 26262 and provides objective data to guide improvements in DFT. Tessent DefectSim dramatically reduces SPICE simulation time compared to simulating every potential defect.
-
Product
PCI Simulation Modules For Sensor Simulation
-
Does your test strategy require simulating environmental sensors, including temperature, pressure, altitude, and strain gauges.
-
Product
Class AAA Steady State Solar Simulator
-
King Design Industrial Co., Ltd.
*Lamp average life 25,000 hours (We offer 1 year warranty including lamps)!*Spectrum Mis-match Class A, without filter! *Irradiance almost no decay within 10,000 hours!*Spectrum maintains stable during power adjustment!
-
Product
Advanced Battery Tester
DBT-12+
-
The tester enables safe measurement of voltage, current rating, state of charge and state of health for 12V and 6V batteries. The device is powered by an internal battery, so it can test even discharged batteries and can be conveniently used as a voltmeter.
-
Product
Data Link Simulator II
-
The Data Link Simulator II simulates a communications link, inserting delays and introducing errors so users can deter-mine what effects these impairments will have on their systems. The Simulator II includes a 35 x 20 character color LCD display. Context-sensitive help screens make it easy to use, without training or reference to a manual.
-
Product
O-RU Simulator
-
With Simnovusās web interface, there is no need to install any software to use the UE simulator.The UE simulator has an intuitive step-by-step workflow to walk users through the generation of even the most complex test profiles in just a few minutes.
-
Product
24 Channel Isolated Counter / Totalizer & 16 Channel Pulse Simulator
DP-cPCI-5004
-
DP-cPCI-5004, Isolated Pulse Simulator / Counter / Totalizer module is an integrated module for pulse output, pulse measurement and event counting. The module has 16 isolated channels of pulse output at desired frequency. The 16 channels are divided into three groups . The first two groups have four differential and one single ended channels each.
-
Product
Safety Voltage Detector ( Rechargeable Battery Type )
350 SVD
-
Standard Electric Works Co., Ltd
āĀ Protection class: IP65āĀ Bright LED visual indicationāĀ Audible indicationāĀ Non-contact voltage detection: Ā Ā Ā Ā 220Vac ~ 132kVacāĀ Wide angle voltage detectionāĀ Frequency range: 40 ~ 70Hz āĀ Easy-to-prove methodāĀ Self-test functionāĀ Power source: 9V rechargeable battery āĀ Non-contact detection by proximityāĀ Flashlight functionāĀ Operating temperature: 0Ā°C~50Ā°CāĀ Humidity: 80% RH MaxāĀ Lightweight, robust and compactāĀ Comply with EN 61326-1
-
Product
UE Simulator
-
With Simnovus, you get superior value as our software runs on COTS and SDR enabling you to deploy multiple test beds. You do not have to spend millions on expensive Capex.
-
Product
Mechanical Simulation in Matlab
-
There are variety of numerical possibilities in the MATLAB and Simulink simulation environment. For those simulation environments we offer you various toolboxes that allow you to perform simulations easily and efficiently. These toolboxes can be combined with all available ways of MATLAB and Simulink. Our toolboxes can provide you support in the following areas: Analysis of structural dynamic behavior, Vibration and noise abatement, Design of active systems, Model Reduction, Ansys-Matlab interface.
-
Product
Automatic Batteries with Filters with Thyristors
BATLVFS400
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of powerfactor in low voltage instalations.
-
Product
Linktropy Network Delay Simulator
-
Linktropy Emulators Provide Affordable Network Emulation for Accurate, Repeatable Performance Testing at Speeds up to 1 Gbps
-
Product
Battery Discharge Test Unit
125V DC 100A
-
KV Hipot Power Test Equipment Co.,Ltd
Battery Discharge Capacity Tester is used to perform discharge testing which is the verifiable method to determine actual capacity of battery systems.
-
Product
Circuit Simulation & PCB Design Software
TINA Design Suite
-
TINA Design Suite s a powerful yet affordable circuit simulation and PCB design software package for analyzing, designing, and real time testing of analog, digital, HDL, MCU, and mixed electronic circuits and their PCB layouts. You can also analyze SMPS, RF, communication, and optoelectronic circuits; generate and debug MCU code using the integrated flowchart tool; and test microcontroller applications in a mixed circuit environment.
-
Product
Laboratory Battery Tester With Integrated Chamber
-
Compact and versatile, our portable desktop solution integrates Arbin's advanced testing features.
-
Product
MIL-STD-1553 A / B Test And Simulation PCI Module
PCI-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
Battery Load Tester
Battery Beak
-
Cross the Road Electronics, LLC
The Battery Beak is a battery load tester that is capable of delivering an 18 amp load and measuring a batteries internal resistance, state of charge (SOC), and can determine the overall health of the battery. The Battery Beak supports all battery chemistries but has additional features to determine battery health for both Lead Acid and NiMH chemistries and supports a variety of AmpHour/Voltage combinations.
-
Product
GNSS Simulator
NCS NOVA
-
The NCS NOVA is IFENĀ“s newest RF signal generator technology based on a modular and highly flexible Software Defined Radio (SDR) platform. This flexibility makes the NCS NOVA the ideal choice for a wide range of test applications.The NCS NOVA`s full upgradeability makes it a future-proof investment for the upcoming multi-frequency era in commercial and professional applications. It is far more than just a GPS/GNSS Simulator!
-
Product
Gyro Simulator for Aircraft or Bench Use
TA-256A
-
This is a transformer isolated gyro simulator that can substitute for the KI256 attitude indicator and thus eliminate the requirement to remove that gyro to a remote stand and route a vacuum or pressure source out to the aircraft.
-
Product
Battery Management Chip Module
Sentinel
-
The first single system on chip module. Measures cell voltage, cell internal temperature and cell impedance.
-
Product
Regenerative Battery Pack Test System
17040
Test System
Conforms to international standards for battery testing: IEC, ISO, UL, and GB/T, etc.Regenerative battery energy discharge (Eff. >90%, PF >0.95, I_THD <5%)Multiple voltage and current ranges for auto ranging function to provide optimum resolutionHigh accuracy current/voltage measurement (0.05%FS/0.02%FS)2ms current slew rate (-90% ~ 90%)Dynamic (current/power) driving profile simulation tests for NEDC, FUDS, HPPCTest channel parallel functionTest data analysis functionData recovery protection (after power failure)Automatic protection for error conditionBattery simulator (option)High power testing equipment- Voltage range : 80~1000V - Current range : 0~750A - Power range : 0~300kWCustomized integration functions- Integrated temperature chamber - BMS data analysis - Multi-channel voltage/temperature recording
-
Product
Battery Testers
-
When diagnosing a starting system issue, it is important to pinpoint the exact source of the problem to avoid warranty/replacement of the wrong part, reduce vehicle comebacks and maintain customer satisfaction. BA Series testers provide the detailed data needed to make the right call. Model Nos. BA5 and BA7 are economical enough to be used as triage testers at busy repair facilities. Put them in the hands of every tech in the shop and watch efficiency skyrocket.
