-
Product
Universal Automated Programming System
4900
-
The 4900 is powered by the newest BPM 9th generation technology, which delivers the fastest programming speeds in the industry for MCU’s, eMMC HS400, NAND, NOR and Serial Flash devices. BPM 9th generation technology produces 200 MHz signals, allowing each byte of data to transfer in up to 2.5 ns. Up to 9 times faster than competing programmers. 3D Vision option inspects BGA, CSP, QFP, TSOP, SOIC and J-Lead devices for coplanarity, bent lead, pitch, width, diameter, standoff and XY errors.
-
Product
Autoinjector Testing System
-
Instron’s Autoinjector Testing System is designed to perform full functionality testing on a wide variety of drug delivery devices, including safety syringes and both needle shield and button-activated formats. Developed in collaboration with pharmaceutical manufacturers and CDMOs, the system captures essential performance requirements such as activation force, injection time, dose accuracy, needle depth, and click detection. It supports compliance with international standards like ISO 11608 and can be configured for integration with collaborative robots to enhance automation and throughput.
-
Product
Backplane Test System
402HV
-
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
Product
EW System Test Set
MS 1107
-
PSS LRU Test Set is used to test the RWR (Radar Warning Receiver) system by simulating the input signals and testing the output signals.
-
Product
Slip Ring Test System
-
This is a high specification tester that will measure many cable parameters. It measures cable resistance very accurately using the Kelvin 4-wire method. It also tests for shorts between pins at a low voltage. The next test is to measure insulation between connections at a higher voltage. This is carried out at up to 1500 Volts DC with resistances of 10 to 500 Meg ohms.
-
Product
Scienlab Battery Test System – Cell Level
SL113XA | SL100XA Series
-
The cell is the basis of any battery system and directly influences its function, performance and safety. Therefore, it is essential to test and characterize the cell at an early development stage. For this purpose, Keysight offers reliable test systems for precise and reproducible measurement results. The Cell Level Series (SL1002A, SL1004A, SL1007A, SL1132A and SL1133A) — also known as Battery Cell Tester — emulates sink and source for battery cells for automotive and industrial applications.
-
Product
Discrete Devices High-speed Testing System
-
QT-6000 discrete device high-speed testing machine is suitable for testing small and medium-power diodes, transistors, field effect transistors and other products and wafers. It can expand built-in capacitance testing (DC+CAP), EAS, VC, pA modules, as well as external LCR (ultra high precision capacitance testing), Scanbox, etc. The machine can be used for FT mass production testing or laboratory testing.
-
Product
(1000kN) Fatigue Testing Systems
8805
-
The 8805 is a 4-column, 1000 kN servohydraulic fatigue testing machine. It features a high-stiffness and precision-aligned load frame, with hydraulic lifts and locks, and an actuator in the upper crosshead.
-
Product
Electro-Stimulation Equipment Testing System
STIMU-600
-
Test device for functional testing of electrical stimulation devices.
-
Product
GSP-2B Test System Interface Probe
GSP-2B
ICT/FCT Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 125Full Travel (mm): 3.18Recommended Travel (mil): 125Recommended Travel (mm): 3.18Overall Length (mil): 845Overall Length (mm): 21.46
-
Product
High Impact Shock Test System
KRD16 series
-
High impact shock test system meets MIL-S-901D standard which covers shock testing requirements for ship board machinery, equipment, systems, and structures, excluding submarine pressure hull penetrations. The purpose of these requirements is to verify the ability of shipboard installations to withstand shock loadings which may be incurred during wartime service due to the effects of nuclear or conventional weapons.
-
Product
Shock Test Systems
-
Accurately measure the fragility of products and evaluate how they respond to specific shock inputs.
-
Product
Incircuit and Functional Test Systems
-
REINHARDT System- und Messelectronic GmbH
We offer test systems which vary in their expansion and can be used for different ranges of automatic testing.
-
Product
OLED Life Time Test System
-
A system for measuring measurement items (brightness and so forth through Voltage, Current, and Photodiode) and their lifetime in intervals of set time, while supplying power to multiple (32 Channel) OLED panel stably.
-
Product
Automated Discrete Semiconductor Tester (ATE)
5300HX
-
The Model 5300HX Automated Discrete Semiconductor Tester (ATE) is designed for fast, reliable testing of a wide range of discrete devices. Using an on-board Intel SBC, can provide stand alone testing capability or connected to a PC for intuitive test development and data capture.
-
Product
Resilient Modulus and Asphalt Testing System
-
The Resilient Modulus software features built and test sequences, and the capability to specify user defined sequences. Contact stress is automatically adjusted according to the above procedures as selected. Available waveforms include haver sine, sine, square and triangular, along with a user defined waveform selection. Optional peak & valley compensation ensures proper and quick matching of the load parameters. Real time displays of the prescribed versus actual dynamic load or the dynamic deformation measurements by each sensor are always present. Deformation ratio of the two sensors, Rv (to ensure that the two deformation sensors are in agreement) and Mr are also calculated in real time. During export, curve fitting is done to fit the results to models that predict Mr as a function of σm, σd, and CP (cell pressure). Four different functions are calculated automatically
-
Product
Small Drop Test System
KRD41 series
-
KRD41 series small drop tester is suitable for free-fall test of small consumer electronics and components such as mobile phones, walkie-talkies, electronic dictionaries, CD / MD / MP3 and so on, applicable standards JISC 0044 and IEC 60068-2-32. Through standard tests on electronic products (surface drop, corner drop, edge drop, etc.) and collecting data, it simulates the vertical drop impact of electronic products during transportation and handling. It provides a basis for the design of the product's buffer and vibration damping and the selection of structural materials.
-
Product
Otii Automation Toolbox
-
Otii Automation Toolbox is a software add-on to Otii Pro software. It is a subscription-based software that you can subscribe to monthly or annually and cancel anytime. Works on all Otii boxes.
-
Product
Portable Test System
MT786
-
Actual value, vector, curve displayCurrent and voltage generationerror measurementMeasurement of harmonics up to the 40th
-
Product
Automation
Signal Filtration
-
Signal Filtration is used for filtering signals coming to the input channels of spectrum analyzers, strain-gauge stations, and seismic stations, for further processing by ZETLAB programs. Signal Filtration can also be used for processing virtual channels created by such programs as Vibration Meter, Strain-Gauge Sensor, etc. Signal Filtration operates with signals both in real time and with reproduced of recorded signals.
-
Product
Electronic Test And Measurement Systems
-
Summaries, information, & tutorials about electronics test and measurement equipment & techniques.
-
Product
Standalone Test System
1000 Series ATE
-
The Circuit Check 1000 Series ATE provides a configurable standard platform that can utilize multiple mass interconnect interfaces while providing ease of maintenance and the ability to accept a wide variety of test fixture solutions. With the 1000 Series ATE, test procedures become automatic, with test steps and go/no-go limits easily programmable.
-
Product
Process Automation Platform And Software
-
Stable and robust processes require sophisticated control of critical process parameters (CPPs) based on reliable data acquisition, storage and evaluation capabilities. State-of the-art process control prevents or mitigates risks of producing faulty batches and represents a further step towards knowledge- and risk-based production of biopharmaceutical products.
-
Product
Temperature/Humidity Vibration Test Systems
EHVC SERIES
-
The EHVC Series is designed for highly accelerated life testing, the demand of which from customers is increasing today. This is a joint system of the AGREE chamber and thermal shock chamber that we have manufactured and makes the temperature rate up to 20℃/min feasible with a compressor only. With this feature, the highly accelerated life test such as AGREE tests, most thermal shock tests can be performed with one unit.
-
Product
Electro-Dynamic Vibration Test System (Air Cooled)
-
HIACC Engineering & Services Pvt. Ltd.
The air-cooled electro-dynamic vibration test system has a wide frequency range, high reliability, easy to operate and small foot-print area. The force ranges from 1kN to 70kN, and maximum load is from 70 kg to 1000 kg. This product can be integrated with HIACC’s environmental chambers.
-
Product
Automated Low Humidity Generation System
3920
-
The Model 3920 Low Humidity Generation System is a self-contained system capable of producing atmospheres of known humidity using the fundamental "two-pressure" principle. This system is capable of continuously supplying frost point, dew point, parts per million, relative humidity and other calculated values for instrument calibration and evaluation as well as for precision environmental testing.
-
Product
15V6A Battery Pack Test System
TOB-BTS-15V6A
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channels 15V6A Battery Pack Test System Laptop Battery Performance Testing. TOB-BTS-15V6A Battery tester equipment is an eight-channel battery analyzer to analyze polymer battery and cylindrical batteries from 12 mA to 6000 mA, up to 15V.
-
Product
Automated Front & Backside Mask Aligner System
Model 6000
-
With over 4 decades of manufacturing in the semiconductor industry, OAI meets the growing challenge of a dynamic market with an elite class of production photolithography equipment. Built on the proven OAI modular platform, the Model 6000 has front and backside alignment that is fully automated with a submicron printing capability as well as submicron top to bottom front side alignment accuracy which delivers performance that is unmatched at any price. Choose either topside or optional backside alignment which uses OAI’s customized advanced recognition pattern software. These Mask Aligners have OAI’s Advanced Beam Optics with better than ±3% uniformity and a throughput of 200 wafers per hour in first mask mode, which results in higher yields. The Series 6000 can handle a wide variety of wafers from thick and bonded substrates (up to 7000 microns), warped wafers (up to 7 mm-10mm), thin substrates (down to 100 micron thick), and thick photo resist.
-
Product
Cellular Base Station Factory Test Systems
-
*Factory Test System*Designed and Built by BCO*100% Functional Testing*Environmental Stress Screening Testing
-
Product
1RU Automated Switch Unit
UC1
-
Universal Switching Corporation
The UC1 switch system provides a modular solution for a variety of signals up to 50GHz, and is designed for smaller requirements. This product delivers ultra-high signal performance coupled with advanced remote/manual control and monitoring with 10/100 LXI certified Ethernet port, multi-serial port, front panel control, direct alarm input port, and auto-sense (on some PUC's).
