AC Current Clamps
wrap around conductors to measure current.
-
Product
Current Probes
-
Tektronix current probe solutions offer:*The broadest range of AC/DC and AC-only current probes*Measurement accuracy from uAs to 2000 A*Best-in-class bandwidth up to 120 MHz*Best-in-class current clamp sensitivity down to 1 mA*The only products with 3rd Party Safety Certification (UL, CSA, ETL)*The only products with bare wire voltage ratings*Automatic readout and scaling when used with Tektronix oscilloscopes so you don’t have to convert volts to amps or manually set the scaling
-
Product
Differential Current Management
-
All devices from the series/products listed below can be expanded with the "dual-channel residual current detection" add-on module to enable residual current monitoring. By comparing residual current and protective conductor current measurements, you can detect stray currents in your electrical system and initiate appropriate countermeasures.
-
Product
Clamp Meter
ECLIPSE
-
ECLIPSE has been designed to measure AC/DC current up to 1000A, DC voltage up to 1500V and AC voltage up to 1000V in TRMS reaching CAT IV 600V and CAT III 1000V in compliance with safety standard IEC/EN61010-1. The clamp is provided with a display with 6000 measuring spots with backlight and bargraph to allow for a simple reading even in poorly lit environments.
-
Product
AC Hipot Tester
-
KV Hipot Power Test Equipment Co.,Ltd
The Hipot tester is a nondestructive test which is a effective way to determine the insulation strength for electric equipment.
-
Product
AC/DC Clamp Meter
3900 CL
-
Standard Electric Works Co., Ltd
● 4000- count LCD.● Full automatic measurement. ◎ Voltage measurement. ◎ Current measurement. ◎ Resistor measurement. ◎ External frequency measurement.● Range change function.● Data Hold function freezes the reading.● REL function.● Peak function.● VAHz mode measures frequency in ACV and ACA mode.● Max/Min function.● Continuity check.● Low battery indication.● Auto Power Off (APO) function.● Safety design throughout with no exposed metal parts, shielded banana plugs and recessed input terminals.
-
Product
Current Amplifier/Generator
ULCA-1
-
The Ultrastable Low-noise Current Amplifier ULCA-1 is designed to fulfill the needs of high-accuracy low-current generation and measurements in the range from 1 fA to 1 µA (licensed by PTB).
-
Product
Current Sources
-
Innovar Current Sources are the standard in the circuit breaker industry. Our Current Sources supply regulated current from 1 amp to 100,000 amps with incredible accuracy, along with providing a full set of features that is unmatched by any other Current Source in the market.
-
Product
Selective AC Voltmeter
-
The AC Selective AC Voltmeter is designed to measure. The number of signals is eliminated.
-
Product
Programmable AC Power Source
6400
-
Chroma Systems Solutions, Inc.
The Chroma 6400 series Programmable AC Power Source uses state of the art PWM technology to deliver pure, instrument grade AC power at a very low cost never achieved before. The 6400 AC power source offers maximum rated power for any output voltage from 0 to 300VAC, at any frequency from 45 to 1K Hz. It is not only suitable for commercial applications (47-63Hz), but also for avionics, marine, military applications at 400Hz.
-
Product
AC Test Transformer
-
Shanghai Guantu Technology Co., Ltd.
How the AC test transformer prevents the overvoltage generated by the frequency conversion series resonance test device is a relatively simple problem, but the overvoltage caused by voltage fluctuation is difficult to appear when the overvoltage protection is set. Generally, the overvoltage of the frequency conversion series resonance test device will appear in the frequency sweep stage of the instrument, that is, in the process of finding the resonance point. Those who have used it know that in the process of finding the resonance point of the frequency conversion series resonance test device, the voltage and frequency have a parabola-like linear relationship. By default, the system finds the high voltage, that is, the apex of the parabola as the resonance point.
-
Product
ITA, iCon, Extended Cable Clamp
410123115
ITA
This iCon ITA includes an extended cable clamp to accommodate larger cable bundles. The maximum cable bundle area = 1.97 " sq. or a 1.58"/40.13mm diameter bundle. The clamp may be inverted for smaller cable bundles.Please note: This ITA does not offer an increased bend radius that may occur with a larger cable bundle radius. Larger bend radius is offered by the iCon XL, p/n 410123232.
-
Product
AC Source
5310（0~500Vrms/1KVA）
-
Voltage output has totally six ranges，maximum up to 500V，convenient for 300V above the voltage regulation test
-
Product
Current Transformer
-
A precision electrical device used to step down high alternating (AC) or direct (DC) primary currents into safe, measurable secondary values for power analysis, energy management, and monitoring instruments.
-
Product
Current Meter
Model 106
-
The Model 106 is the ideal instrument for coastal and estuarine applications and other light-duty survey work.
-
Product
Clamp Meter, Auto, True RMS, 1 kA AC, 600 V AC, 50 mm Jaw Opening Max.
72-10445
-
The 72-10445 is a Clamp Power Meter Clamp with phase sequence. It measures active power (W), apparent power (VA), reactive power (VAr), power factor, phase angle and active energy (Wh) with built-in phase sequence test. Also measures AC current, AC voltage and frequency.
-
Product
C/I Clamp Meters
CLAMPMETER,OPEN JAW (CSJ-100)
-
*AC amperage, AC/DC voltage measurement*Open jaw design eases AC current measurement*Slim profile with build-inprobe storage on back*Measures resistance up to 20MΩ*Audible continuity and diode test*Bright LED and audible alarm for non-contact voltage detection*Auto power off for longer battery life*Data hold to capture measurements*2000 count LCD*Accessories included: (2)1.5V AAA batteries, test leads and carrying case*Lifetime Limited Warranty
-
Product
Clamp Meter, Auto, True RMS, 1 kA AC, 600 V AC, 600 V DC
72-9485
-
A professional digital clamp meter that is perfect for any industry. Measures AC/DC voltage, AC/DC current, Resistance, and Frequency.
-
Product
AC Engine Dynamometer
DA900
-
Power: 1000 hp (746 kW)Torque: 3,501 lb-ft (4,747 Nm)Maximum Speed: 3,000 rpmConstant Torque Range: 0 - 1,600 rpmConstant Power Range: 1,600 - 2,400 rpmDecreasing Power Range: 2,400 - 3,000 rpmRotation: bi-directional
-
-
Product
Current Probe For Non-Intrusive Measurement Of AC, DC, And Waveform Currents
CP 305
-
The CP 305 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.Using advanced Hall Effect technology the CP 305 can measure currents accurately up to 450A peak over the frequency range of DC to 20 kHz.
-
Product
Probe “Socket” Clamps
LCP-S12
-
A simple and cost-effective option for mounting Small-aperture Probes in the probe plate. A Socket Clamp tool is needed for insertion and removal of the clamp in the probe plate
-
Product
AC Insulation Testing
-
AC insulation tests are a popular response to the increasingly demanding industrial, power and domestic marketplaces. Insulation materials have had to become more efficient to keep up with demand; more efficient equipment requires less insulation material to meet the minimum acceptable value of insulation resistance. In turn, cables have become smaller and lighter. However, under certain higher stress testing conditions such as DC testing, cables like Crossed Linked Polyethylene (XLPE) can quickly degrade.
-
Product
AC Engine Dynamometer
DA195
-
Power: 195 hp (145.4 kW)Torque: 682 lb-ft (924.7 Nm)Maximum Speed: 5,600 rpmConstant Torque Range: 0 - 1,500 rpmConstant Power Range: 1,500 - 2,700 rpmDecreasing Power Range: 2,700 - 5,600 rpmRotation: bi-directional
-
Product
Integrated Current Sensors
GO series
-
*Standard package and small footprint*Cost effective*A perfect compromise for small drives, robots, solar inverters, e-bikes etc.
-
Product
Current Generator
MIG1260
-
MIG1260 is a current generator with wave shape 8/20 μs. The exact waveform delivered is a function of the surge generator and the impedance to which the surge is applied. The generator can deliver up to 60kA impulse current supported by 12kV impulse voltage, making it ideal for testing big varistors with high hold-on voltage. Mechanically the MIG1260 consists of one large rack and a separate control console with high voltage output terminals protected by a glass acrylic test cabinet.
-
Product
AC Electronic Load
IT8600 Series
-
IT8600 is ITECH latest series of AC/DC electronic loads with power range 0~14.4 kVA and adjustable frequency 45 Hz ~ 450 Hz. The unique oscilloscope waveform display function of IT8600's can display input voltage & current as waveform. It is equipped with measurement modes for different parameters such as inrush current, peak value, effective value, PF (power factor).
-
Product
Clamp Meters
-
Fujian Lilliput Optoelectronics Technology Co., Ltd.
We are one of the leading and professional clamp meters manufacturers and suppliers in China. Thanks to our highly qualified experts and advanced technology, we are also one of the world's leading brands. Welcome to buy the quality, cheap and durable clamp meters in stock from us. Check the quotation with us now.
-
Product
3.5 Digit Handheld Clamp Meters
U1190 Series
Digital Multimeter
Keysight’s U1190 Series clamp multimeters incorporate features to help you work more conveniently and safely. Housed in robust cases, these ergonomic handheld digital multimeters (DMM) fit comfortably in the palm of your hand and let you select functions with just a thumb press. A Keysight clamp multimeter is different from most other clamp multimeters because it also features handheld DMM functionality.
-
Product
AC Power Sources
400XAC Series
-
Our 400XAC Series AC Power Sources provides both 1Ø and 3Ø AC or DC power in a single box solution. If you need an AC Power Source with superior application flexibility, look no further than the EEC 400XAC. Ideal for both production and laboratory use, this 3 phase AC Power Source provides a unique feature set at a competitive price point. Our exclusive SmartCONFIG feature allows the 400XAC Series to switch from 1 phase to 3 phase power with the push of a button. This flexibility maximizes your investment while providing you the AC and DC power that your application needs. The 400XAC Series AC Power Source includes the following models: 430XAC and 460XAC.
-
Product
Split type AC Current Transformer
CTS-400
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*5A output for metering application.*Short circuit switch for secondary output is provided for safe operation.*High accurate transformer for the application of first class meter.*Easy to install by metal fitting.
