Electrical Testers
-
Product
Sensor Tester
QST-5
-
The QST-5 device is intended for testing many popular sensors used in the automotive industry. The tester powers the tested sensors by itself, so it can be used both in a vehicle and outside of it.
-
Product
Martindale Abrasion Tester
GT-KC13A
-
To determine the abrasion resistance of all kinds of footwear vamp material. Samples are rubbed against known abrasion at low pressures and in continuously changing directions and the amount of abrasion. The unique design allows removal of individual sample holders for examination without lifting the top motion plate.
-
Product
Multicom Tester
IQ2010
-
The LitePoint IQ2010™ is a comprehensive, one-box test solution for all your connectivity testing needs:WiFi, 802.11a/b/g/n and 802.11pBluetooth, Classic (1.x, 2.x, 3.0) and Low Energy (4.0)GPSFMMIMOWiMAXZigBee
-
Product
Combustion Leak Tester
AC560000
-
Fast, economical and accurate method to test for combustion gas leaks in head gaskets, cylinder heads and engine blocks. Dual chamber design provides more accurate test results. Test fluid can be used for both gasoline and diesel engines.
-
Product
PID Insulation Tester
TOS7210S
-
The PID insulation tester (TOS7210S) is designed based on the insulation resistance tester (TOS7200) to carry out the evaluation of the PID (Potential Induced Degradation) effect of the PV module precisely and efficiently. Being equipped with the output ability of 2000 V and the ammeter with nA resolution as well as a polarity switching function, the TOS7210S is also applicable not only to the PID evaluation but also the evaluation of the insulators that requires a high sensitivity of measurement. The tester is equipped with the panel memory that is externally accessible and RS232C interface as standard; it can be flexibly compatible with the automated system.
-
Product
Tensile tester
TS-2000
-
Advantage server motor, high quality warm gear gearbox, and precise roll bearing screw are adopted to ensure tensile tester machine the accurate control and results.
-
-
Product
Multifunction Tester
COMBI521
-
COMBI521 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
Digital Harmonics Clamp Tester
HWT-301
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Harmonics and leakage current measurements.*Up to 25th harmonics current and voltage measurements.*True rms reading for ACA and ACV.*Data-hold and Auto power off function.*Conform to IEC safety requirements.
-
Product
Inline Wafer Electrical quality Inspection
ILS-W2
-
the Ultimate Wafer Electrical Quality Inspection Unit for Wafer Inspection Systems
-
Product
Battery Cell Insulation Tester
Chroma 11210
-
Chroma Systems Solutions, Inc.
Chroma 11210 battery cell insulation tester is an instrument used for accurately measuring leakage current (LC) and insulation resistance(IR) of battery jelly-roll/dry-cell as well as other insulation materials. In addition to standard LC/IR measurement, the 11210 has a unique function that detects partial discharge (PD) or flashover that may have occurred inside the insulation material during the high voltage insulation testing process.
-
Product
Dead Weight Pressure Tester
-
Unitech Scales And Measurements Pvt. Ltd
Dead Weight Pressure Gauge Tester is ideal for testing and calibration of pressure gauges,pressure transducers,recorders,digital calibrators etc. The system used in the dead weight is vertically mounted precision lapped piston and cylinder assembly with accurately calibrated mass for loading the piston. Pressure is built easily by single cylinder pump at very high rate. The whole system is housed inside a stainless steel case with elegant look. Pressure ports are provided to fix the gauges to be tested. Acrylic see-through oil tank is designed to use it as oil reservoir.
-
Product
Audio Cable Testers
AudioJog Pro 5
-
ALL new Audio cable tester with SINGLE & DOUBLE ended testing. There are 2 rows of 6 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found.
-
Product
Waterproof pH Tester
pHTestr 10BNC
-
Large Display Screen - dual display LCD for enhanced readability, provides comprehensive meter information
-
Product
Fluorescent Light Tester
1000FLT
-
The Fluke 1000FLT performs all five essential tests with one compact tool. If your job requires keeping large numbers of fluorescent lights shining, the Fluke 1000FLT is an indispensable tool that saves time and money.
-
Product
High Voltage Surge Testers
HVST
-
The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. This voltage is displayed on an oscilloscope and recorded on the Pass/ Fail LED latch monitor. This voltage will be accurate despite the impedance of the winding being tested. The insulation system can be tested way above the operating voltage because of the brief duration of the applied voltage test pulse. This allows faults to be detected long before they become apparent at operating conditions.
-
Product
Lan Cable Tester
3PK-NT015N
-
Open/short wiring testConnected wires displayNo wire or termination indicationWrong connection / Non-parallel connectionEthernet 10 base2 termination value detectionBattery low indicationBuzzer insideBNC for testing 10 BASE2 terminator valueIsolation resistances 50 K ohms test
-
Product
Phenolphthalein Solution Pinhole Tester
FTS-30
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-5Used to detect pinhole on the film of enameled wires; it is mainly designed to indicate the position of pinhole by the color of phenolphthalein indicator and visually inspect the number of pinhole;Detection range is not subject to the limitation of wire size and specification;It is an economic and indispensable pinhole detection tool, featuring simple operation, stable, intuitive and reliable data detection.
-
Product
Network Cable Tester
AVJoG Rack
-
*A single box solution for testing AV cables. *Easy to use with only one button operation. *Detects Open, Short and Crossed circuits. *LCD display for test results. *All major AV connectors present, no need for extra adaptors. *40+ preprogrammed cable types.
-
Product
Multifunction Installation Testers
-
Shanghai Beha Electronics Co., Ltd.
Loop impedance and prospective short circuit current measurement• Line impedance and prospective short circuit current measurement• Earth loop resistance in TT-systems• Rotary field test• RCD measurements (contact voltage, trip time, trip current - ramp method)• RCD analysis for test of all RCD parameters • Low Ohm and continuity measurement • Insulation measurement up to 1000V (suitable for 690 V industrial mains systems)• Earth resistance measurement with probes and clamp adapters• Voltage and frequency measurement • Current measurement with clamp adapters(optional)• Power and energy measurements• Harmonics measurement for voltage and current upto the 21st harmonics
-
Product
LED Light Tester
-
The T100L Automatic LED Light Test Equipment is designed to identify the presence of any defects of electronic components for LED light applications, addressing any high-volume production testing challenges without needing expensive test fixtures with fiber optics
-
Product
Film Tearing Strength Tester
DRK108C
-
Shandong Drick Instruments Co., Ltd.
DRK108C Tearing Tester is applicable in the tearing test of films, sheets, flexible PVC, PVDC, waterproof films, woven materials, polypropylene, polyester, paper, cardboard, textile and non-woven, etc.
-
Product
Electrical Safety Analyzers
-
Built on the Vision Pad Platform, the vPad-ES Rugged is the ideal Electrical Safety Analyzer for Field Service Engineers.Housed in an Extreme Duty case, the vPad-ES Rugged offers the functionality and scalability that you have come to expect from Vision Pad Technology products plus the added assurance of knowing your system will be protected in the harshest of environments.
-
Product
Power Supply Tester
UTS-325
-
UTS and STS systems are based on the Autotest A100 Instrument bus which provides a GPIB interface to load and source control and monitoring along with a measurement path matrix, timer/counter/trigger and peak detector instruments, user assignable relays and drivers.
-
-
Product
CDM Tester
-
Hanwa Electronic Ind. Co.,Ltd.
The tester implements to test the withstand voltage which occurs when the device contact to different electric potential object.
-
Product
IMPULSE SURGE WINDING TESTER
VE2882A-5U
-
Impulse Tester can detect turn & layer short ,the differences in the number of turns and the material of the core. If high impulse voltage is applied, the poor insulation will appear as a corona or layer discharge.
-
Product
Insulation Tester Calibrator
M191
-
High resistance calibrator for insulation testers up to 10 kV. Other insulation related functions include HV capacitance, short current, dielectric and polarization parameters and timer test.
-
Product
AMIDA ATI 600 Tester
-
AMIDA ATI 600 Tester is a dedicated test system for semiconductor components (MOSFET, BJT, DIODE, ... etc.), which can accurately and quickly measure product parameters through form filling and editable program control. In practical applications, AMIDA ATI 600 Tester is the best choice for users, whether it is CP or FT mass production testing, or research projects of component characteristics.
-
Product
Wire & Cable Testers
-
Precision Mastech Enterprises Co.
Diagnostic tools designed to verify electrical connectivity, map wiring configurations, and detect faults.
