Simulation
the approximation of actual operational conditions.
See Also: Simulators, Simulation Software, Simulation Testing, Modelling, Emulation
-
product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
product
Test Automation System for Driveline Testing
STARS Driveline
STARS Driveline is an integrated automation, acquisition and control system that provides a broad range of application functionality in a single, powerful environment. It has been designed to fulfil the specialist requirements and applications for driveline testing from simple modal testing on two or four wheel drive systems, to RLS simulation or advanced applications such as service load replication (SLR).
-
product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 62.1Ω
40-251-011
The 40-251-011 is a programmable resistor module with 8 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
Satellite Simulators
Tampa Microwave''s satellite simulators provide a compact easy to use training and evaluation tool for satellite earth terminals. We provide a variety of models with different combinations of frequency bands, transmit/receive strength, atmospheric effects and form factors. Contact us with your requirements and we will recommend a cost effective solution.
-
product
PV-IV Solutions
We offer a broad range of PV IV Measurement systems for measuring solar cells from 3 mm to 300 x 300 mm. The wide range of solar simulators, vacuum chuck test stations, and electronic loads make it impossible to list “standard solutions” Most systems are put together for individual customer needs based on cell type and contact geometry of the devices being tested. Over the last several years we have designed and manufactured a wide range test solutions for many different types of cells and contact geometries. In most cases a customized solution is no more than a slight customization of a standard platform that has been previously designed.
-
product
Introduction to Graphical User Interface - Softpanel
61800 Series
The increased demand for Distributed Energy Resource (DR) products such as PV Inverter and Wind Energy systems, have increased the demand for regulation test standards to insure proper operation and safety of on-grid products. Manufacturers testing to prove compliance, need test equipment that can simulate and measure and test their products. Chroma’s 61800 family of Regenerative Grid Simulators provide a full 4 quadrant, regenerative, grid simulation for compliance, safety, and product verification testing
-
product
Battery Test Equipment
Shenzhen Bonad Instrument Co., Ltd.
The tests that can be performed by lithium-ion battery safety testing equipment include temperature cycling test, thermal abuse test, high altitude low-pressure simulation test, vibration test, shock test, external short-circuit test, forced internal short-circuit test, drop test, crush test, impact test, nail penetration test, burning test, etc. These test items mainly apply to various lithium-ion cells such as 18650 cells and prismatic cells, lithium-ion batteries, lithium-ion battery modules, lithium-ion battery packs, and so on.BONAD battery safety testing equipment complies with various standards such as IEC 62133, IEC 62133, UL 2580, UN 38.3, UL 1642, etc. For more information, please contact us, BONAD will provide you with professional technical consultation and high-quality testing equipment.
-
product
PCI High Density Pecision Resistor Card, 18-Channel, 2Ω To 470Ω
50-298-014
The 50-298-014 is a high density programmable resistor card with 18 channels which can be set between 2Ω and 470Ω with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
AC Fuel Flow Signal Generator
TA-100
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
product
Hot Dipping Simulator
HDPS
This is a hot-dip galvanizing simulator that simulates various hot-dip galvanizing processes such as heating, cooling, vacuuming, gas replacement, and spraying of steel sheets on a laboratory scale. It is possible to simulate the parameters close to the actual line, such as zinc bath temperature, immersion speed, immersion time, and gas flow rate adjustment for weight control. Also, 20 to 25 sheets can be tested
-
product
VI-DriveSim
Today's driving simulators are universally recognized as the ultimate tool for vehicle development. The power and versatility of a driving simulator are unparalleled … as long as the software platform is equally powerful.
-
product
PCI High Density Pecision Resistor Card, 9-Channel, 2.5Ω To 472Ω
50-298-020
The 50-298-020 is a high density programmable resistor card with 9 channels which can be set between 2.5Ω and 472Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
AC Power Source
AFC series
The AFC Series is an economically priced AC power source to provide reliable voltage and frequency simulation for general applications, such as testing for home appliance, electronic, medical equipment, lighting and other fields of production or R&D. Utilized PWM switching technology, AFC provides high quality pure sine waveform with output level up to 2,000kVA. The AC source is coupled with output voltage range of 5~300V and output frequency of 47~63Hz, 50/60Hz fixed. User can select optional frequency output of 2 or 4 times standard frequency and 400Hz.
-
product
PXI Strain Gauge Simulator Module 6-Channel, 1.5k
40-265-406
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 1.5kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
Cost-Effective Network Simulator
Emutel Maestro
Emutel Maestro brings you the perfect solution for testing your DSL equipment. Connect to your product while still in your own testing lab and perform those final tests in a real environment, enabling you to identify and solve any problems before they occur on site.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 16.3k Ohm - SPST
40-294-131
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Resistance Temperature Detectors (RTD) Simulators
Simulation of resistance based temperature sensors such as positive or negative temperature coefficient thermistors. Resistance Temperature Detectors (RTDs) can be wire-wound or thin film. Our RTD simulator modules provide a cost-effective method of simulating both PT100 and PT1000 RTD sensor types that require fine setting resolution.
-
product
Software Tester & Test Manager
With their ability to replicate all types of networks (i.e. Wide Area Networks, the Cloud, over Wireless, Radio and Satellite links etc. ) iTrinegy network emulators provide testers with the ability to test application performance in a realistic simulation of the target network environment.
-
product
Intelligent Interface Card
IIB-1553-CPCI
The IIB-1553-CPCI is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the CompactPCI bus, with 1553A, 1553B, McAir and STANAG 3838 capability on a single card.The IIB-1553-CPCI supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes,with full error detection in BC, RT, BM and CBM modes. The unit provides a dual redundant 1553 interface.2 Mbytes of dual ported RAM are supplied as standard. The board is supplied with C drivers in source code and Windows menu driven software.
-
product
RF And Microwave Signal Generation And Analysis
The need for microwave test and measurement technology is even more urgent than the need for microwave equipment itself. Therefore, Shengbo Technology is relying on its own research and development capabilities to strive to become one of the comprehensive microwave test and measurement equipment suppliers. We provide a wide range of RF microwave test products, including a good-quality full-band broadband up-down converter . You can provide 2GHz real-time bandwidth signal up-down conversion function in the frequency range of 0.1 ~ 40 + GHz. With our channel simulator , we Became the first company in the world to provide channel analog solutions in such a wide range of broadband signals. At the same time, we are also an innovativesupplier of noise sources and multi-channel microwave signal sources in the industry.
-
product
PXI Resistor Module 4-Channel 1R to 510R
40-293-014
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Pulsed IV-Curve Solutions
Pulsed IV-Curve Test and Analysis System is our new development for 2015. It is an advanced and compact pulsed IV-curve characterization system designed to simulate pulsed ESD events such as TLP, vf-TLP, HMM, HBM, EFT, and LV-Surge. It will monitor the transient voltage and current waveform during the pulse in ps or ns segment, and test the pre- and post-pulse status (leakage current, breakdown voltage, biasing current, static IV curve, etc) of the device under test (DUT), such as protection devices, semiconductors, circuit modules, touch panel sensor, etc.
-
product
Altitude Testing
Our environmental testing facilities simulate altitude testing from -400 ft. (-121 meters) to outer space at 100,000 ft. (30,480 meters) or up to 10-6 Torr (1.3e-7 kPa) with temperature applied as low as -300°F (180C). We can reach these heights within 5 minutes or less. We are capable to handle products measuring up to 4ft X 4ft X 8ft to many standards, including MIL-STD-810 and RTCA DO-160.
-
product
PXI Precision Programmable Resistor Modules
Pickering's PXI precision programmable resistor modules feature high setting resolution with excellent stability and accuracy through the use of innovative switching networks and software correction techniques. This also means all resistance values can be set - there are no missing values due to switch resistance or resistor tolerance. These modules are ideal for sensor emulation applications that require very fine adjustment and also have the capability of being set as open or short circuit to simulate faults in cabling systems. The range includes modules specifically designed for RTD and strain gauge simulation.
-
product
Thermal Load Boards
Thermal Engineering Associates, Inc.
A Thermal Load Board (TLB) is used to simulate an application printed circuit assembly (PCA) either before all the heat-producing components are available for mounting on the application PCA or if the heat-producing components require complex electronic circuitry to create heat within the components. The TLB is typically designed to be as mechanically and thermally equivalent to the application PCA and usually offers a way to vary the power dissipation of the elements that simulate the heat-producing components.
-
product
PXI Precision Resistor Module 4-Channel, 2 to 52.4k
40-297-133
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
SUNTEST
XLS+
Atlas Material Testing Solutions
The SUNTEST XLS+ is used to check for property changes of materials and products caused by sunlight, temperature and moisture in a short period of time. The aging which, outdoor or indoor, may take place over months or years, such as fading, yellowing or loss of strength, can often be simulated within weeks inside a SUNTEST.
-
product
PXI RTD Simulator Module 12 Channel PT100
40-262-201
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the design principles of our 40-260 PXI Precision Resistor, this RTD simulator module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels.
-
product
Waterproof Test Chamber
JL-XC
JL-XC series waterproof test chamber is mainly used for small electronic and electrical products. Such as lamps, electrical cabinets, electrical components and so one. The products are tested for physical and other related properties under simulated climatic conditions. After the test, it is judged whether the performance of the product meets the requirements by verification, so as to be used in the design, improvement, verification and factory inspection of the product. Comply with IEC60529:2001 《Degrees of protection provided by enclosures (IP Code)》, GB4208-2008 《Shell Protection Grade (IP Code)》 14.2.8 Terms and GB7000.1 《Lamps Part 1: General Requirements and Tests》 9.2.9 Terms.
-
product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 31.5Ω
40-252-110
The 40-252-110 is a programmable resistor module with 2 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
