Simulation
the approximation of actual operational conditions.
See Also: Simulators, Simulation Software, Simulation Testing, Modelling, Emulation
-
Product
Hot Tack Tester
-
Guangzhou Biaoji Packaging Equipment Co., Ltd.
GBPI Hot Tack Tester To test the sticking strength of packaging films after heat sealed with different temperature, pressure and time. It simulates the use of packaging bag and makes impact experiment on the part of hot tack.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 4Ω To 2.97MΩ
50-298-151
-
The 50-298-151 is a high density programmable resistor card with 3 channels which can be set between 4Ω and 2.97MΩ with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI High Density Potentiometer Card 9-Channel, 8-Bit, 0 To 255 Ohm
50-296A-121-9/8
-
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, 1 kV Isolation
41-752A-111
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Arc Flash Analysis
-
ETAP Arc Flash Analysis allows you to identify and analyze high risk arc flash areas in your electrical system, and it also allows simulation of several different methods used by engineers to mitigate high incident energy.
-
Product
Testing of Rear Axle Steering
-
*2 high-precision servo axes for linear load simulation*Communication via CAN / Flexray*Function and noise measurements (NVH)*Supply and discharge of the test specimens via WTs on double belt conveyors*Connection to the production control
-
Product
Altitude Chambers
-
Our Altitude Chambers combine temperature and altitude with optional humidity to test basic components or subassemblies designed for use in a variety of industries. With a CSZ altitude chambers, you can control the temperature environment for testing while simulating various altitudes from site level to 65,000 feet (42 Torr). Altitude testing may be continued without temperature control up to 200,000 feet (.169 Torr). This same chamber may also be used as a temperature/humidity cycling chamber at site level only.
-
Product
Power Supply Voltage Fluctuation Simulator
SG Series
-
Simulator to reproduce DC supply voltage variations phenomena in the vehicle environment for evaluating immunity of automotive electronics. This simulator can perform various tests against voltage variations required by ISO 16750 and other international standards. Please contact us for voltage variations testers to perform testing to manufacturers' private standards.
-
Product
PXI High Density Precision Resistor Module, 4-Channel, 3Ω to 52.4kΩ
40-298-133
-
The 40-298-133 is a high density programmable resistor module with 4 channels which can be set between 3Ω and 52.4kΩ with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Leakage Current Tester
-
Premier's Leakage Current Tester (also known as Hipot Tester) simulates the effect of a person touching exposed metal parts of a product and detects whether or not the leakage current that would flow through the person's body remains below a safe level.
-
Product
PCI Precision Resistor Card 9-Channel, 1Ω To 31.5Ω
50-297-110
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Compensation Block for Thermocouple Simulator Modules
40-965-912
-
The Compensation Block is a accessory specifically designed for the 41-760 and 41-761 Millivolt Thermocouple Simulator modules. This block will give the user the temperature of the front panel junction of the module to cabling. This data can then be combined with other factors, temperature on the other end of the cable for example, to compensate the thermocouple hence increase the accuracy.
-
Product
Altitude Digitizer Test Set & Simulator
ATS-400
-
Test & Simulate Altitude Encoder Parallel and Serial I/O all in One Rugged Test Set! The TCI Model ATS-400 is designed to test, display and simulate the output of Altitude Reporting Equipment, which conform to the ICAO Standard for SSR Pressure Altitude Transmission. In accordance with the U.S. National Standards for I.F.F. Mark X (SIF)/Air Traffic Control Radar Beacon System SIF/ATCRBS.
-
Product
Suspension Component Test Systems
-
Acoustic quality, vehicle dynamics and stability, and driver comfort play an increasingly important role in the development of new chassis and suspension systems – both passive and active. Noises in suspension components can cause customer dissatisfaction and lead to high warranty costs and are difficult to diagnose especially on historically-used, noisy hydraulic test rigs. The MB Suspension Component Test Rig (SCTR) enables dynamic simulation of real road excitations and synthesized waveforms, performing industry-standard Force-Velocity and Force-Displacement tests and low speed friction tests, and assessing other NVH and structure-borne noises for comprehensive performance characterization and sound and vibration analyses on a wide variety of chassis components.
-
Product
cPCI Intelligent Interface Card
IIB-1553-CPC
-
The IIB-1553-CPCI is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the CompactPCI bus, with 1553A, 1553B, McAir and STANAG 3838 capability on a single card.
-
Product
DC Electronic Loads
-
Keysight DC electronic loads provide you with the flexibility to test a wide range of applications from power-supply test to simulation of high-intensity discharge (HID) headlamps. The 16-bit voltage, current and power-measurement system provides both accuracy and convenience, and eliminates the need for a DMM, external shunts and wiring.
-
-
Product
DDoS Testing
-
DDoS testing is a simulation of a DDoS attack performed under controlled conditions with real traffic. The goal of DDoS testing is to answer specific questions about the target environment.DDoS attacks are unique for many organizations in that they are relatively infrequent, but when they do occur they're often catastrophic. This catastrophic nature requires that a strategy be implemented to protect the organization, but a lack of real-world experience may limit the effectiveness of any solution. The infrequency of DDoS attacks often means that IT teams are developing solutions based on the "last attack" and waiting until the "next attack" to determine success. To address these challenges, NimbusDDOS created the first DDoS attack simulation platform. Our DDoS simulation services provide organizations the ability to proactively perform DDoS attack tests, using the same techniques used by real attackers. Unlike a real attack, a DDoS test is performed in a controlled manner and structured in a way to achieve the customer's objectives.
-
Product
Test Bench
BERTA
-
OPAL-RT’s BERTA test bench is a safe, reliable and portable test bench for speed governors, turbines, voltage regulators (AVR) and power system stabilizers (PSS). Equipped with a high-performance real-time simulator programmed with world-renowned RT-LAB software, the BERTA Test bench enables users to easily and comprehensively test real generating units in the power plant, synchronized and transmitting power to the main grid and/or on real controllers connected to a virtual generating unit in laboratory.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 4.09k Ohm With SPDT
50-293-123
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Battery Simulator Module
41-751-001
-
The 41-751 is a low power battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals than can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Product
NIBP Simulators
-
The full-featured SC-5 SimCube® NIBP Simulator provides ECG, Resp, Arrhythmias, Pacer Simulation, IBP, and more for accurate biomedical testing. The SimCube simulates real-life oscillometric pulses by varying both the shape and size of the wave as cuff pressure changes.
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 31.5Ω
40-252-110
-
The 40-252-110 is a programmable resistor module with 2 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Software
Battery Simulator
-
Chroma Systems Solutions, Inc.
Testing battery connected devices with an actual battery can either be cost or time prohibitive especially if multiple channels are required. Our Battery Simulation software is used to validate device functions during development in lieu of an actual battery or batteries. Automotive applications include motor drivers, OBC, DC-DC convertors or chargers, and products of DC bus.
-
Product
Structural Durability Solutions
-
Instron offers a variety of testing systems and rigs for static, quasi-static and dynamic loading of structures and components. This includes Component Test Systems, Shaking Tables, Road Simulators, Axle Test Systems, Full Vehicle Test Systems, Wheel Test Systems, Shock Absorber Test Systems, Elastomer Test System and Dynamic Torsion Test Systems.
-
Product
Double-Roller Dynanometer
R 200/2 DIVIDED | VP 430004
-
Maschinenbau Haldenwang GmbH & Co. KG.
The double roller dynamometer R 200/2 DIVIDED with an eddy current brake on each roller set and pneumatic lifting beam is designed to measure the performance of trucks and stands out due to its extremely robust, durable and low-maintenance construction. The R 200/2 ensures highest measuring accuracy due to the power measurement at a constant rpm, speed or tractive force, including the towing power measurement. For tuning and adjustment tasks the load simulation is evaluated graphically. An extension up to a wheel power of 660 kW is optionally possible.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 4.09k Ohm
50-294-023
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Emissions Dynamometers
MD-AWD-1000-M
-
The MD-1000 sets the industry standard for heavy duty chassis dynamometers due to its rugged design and accurate loading capabilities. The AWD upgrade expands your testing to include full time 4×4/AWD applications! Now your testing capabilities have expanded! Simulate on-highway driving conditions under real world loads. Adjust loading to simulate a host of in-use operating conditions. The AWD 1000 is approved for use in Nevada and Colorado for Diesel Smog Testing.
-
Product
Real-time RF Channels Simulator
RF-LiveSim
-
Covering a frequency range from 50 to 900 MHz, RF Live Simulator can emulate RF channels propagation modes in real-time for a signal bandwidth from 20 kHz to 20 MHz (gaussian noise, multipath, Doppler and frequency drift tools). RF-LiveSim is a cost effective solution for intense automatic non regression tests at the physical layer level. RF-LiveSim includes 1x RF input and 1x RF output ports, and provides a complete set of channel models, either for fixed or mobile propagation environments. Whatever the standard, any type of receiver can be tested. Thanks to its real-time process, from your basic original signal, RF-LiveSim can perform, for instance, efficient regression testing of LTE solutions to check the good behavior and the limits of your receiver when multipathes, Doppler and Gaussian noise are applied.
-
Product
Fiber Optic Qualification & Dispersion Test Links
8800 Family
-
Delaire USA qualification test systems are designed to act as worst-case links for bandwidth/dispersion and attenuation, or to meet the customer's loss, dispersion, and distance requirements for custom applications. Because the test links are constructed from hand-selected, industry-standard fiber and not simulated with dispersion elements, all of the effects including loss, dispersion, and fiber nonlinearities are present and authentic. Typical applications include optical transciever testing and qualification for 40G AND 100G systems
