Battery Testers
verify battery integrity.
See Also: Battery Test, Testers, Battery Checkers, Battery Capacity Testers, Lead Acid Battery Testers, Battery Conductance Testers, Battery Connectors
-
Product
EV And Pack/Module Tester
-
Discover the Series 8500, an innovative and fully automated test system engineered to evaluate the performance of Electric Vehicle (EV) components, Energy Storage batteries, Modules, and Packs in real-world conditions. This high-specification system not only delivers accurate results but also allows the energy produced during discharge to be returned to the electrical grid.Using Maccor’s standard fully featured battery test software, the Series 8500 can perform virtually any type of battery test including FUDS, SFUDS, DST etc. for electric vehicle batteries and standard cycling tests for energy storage devices.
-
Product
Precision Integrated Analog Front End, Controller, & PWM for Battery Test & Formation Systems
-
The AD8452 combines a precision analog front-end controller and switch mode power supply (SMPS), pulse-width modulator (PWM) driver into a single silicon platform for high volume battery testing and formation manufacturing. A precision instrumentation amplifier (in-amp) measures the battery charge/discharge current to better than ±0.1% accuracy, while an equally accurate difference amplifier measures the battery voltage. Internal laser trimmed resistor networks establish the in-amp and difference amplifier gains (66 V/V and 0.4 V/V, respectively), and stabilize the AD8452 performance across the rated operating temperature range.
-
Product
Ultrasonic hardness tester SONOHARD®
SH-21A
-
The SH-21A is very easy to use and requires no special knowledge of hardness testing in order to operate the instrument. The unit includes all four hardness scales and you can switch between them at the touch of a button.
-
Product
Cable Tester
-
WEETECH offers a number of individual testers for the low voltage open test and short test.
-
Product
Gas Permebility Testers
-
Guangzhou Biaoji Packaging Equipment Co., Ltd.
Gas Permebility Testers used to test the gas (o2,N2,C o2, ect) transmission rate of packing materials, such as plastic film, composite film, aluminum-plated film, and so on.
-
Product
Cable Testers
DMX ADAPTER
-
DMX protocol is a standard means of controlling lighting dimmers remotely from a control desk. The standard uses a three wire connection using 5-pin XLR type connectors. These adapters allow the E445, E446 and E447 table testers to be used to test the primary circuit of such cables. Two adapters are required for each cable tester.
-
Product
3-Phase/Motor Rotation Tester
61-521
-
*Identifies three-phase sequences*Indicates motor rotation*Checks for open phases*For use up to 600V*2-year warranty
-
Product
Universal Wireless Tester
UWT
-
The combination of evolving standards and the integration of multiple wireless technologies with a lot RF Ports into new product designs means that measurement speed and quality become a priority to maintain throughput and yield targets. Noffz and NI have partnered to create the Universal Wireless Tester (UWT) to address these test challenges.
-
Product
Textile Tester
USTER TESTER 6-C800
-
The USTER TESTER 6-C800 is ready for the most demanding technical textiles applications. The amazing diversity of technical textiles applications is matched by the wide variety of quality characteristics needed in the raw material used so filament yarn producers know they must work to the most stringent specifications and standards. Quality failings, especially in the critical parameter of yarn evenness, can be expensive, but the USTER TESTER 6-C800 provides fast, accurate testing to the tightest tolerances, protecting filament producers against customer complaints and claims. Raw materials for technical textiles cover a wide range of end-uses and performance requirements. Viscose fibers, for instance, are found in lightweight blouses as well as in wire cording and high-speed car tires. Polyester, common in low-price clothing, is also transformed in special high-tech versions, for sophisticated sportswear and outdoor clothing. Countless other examples of technical applications for filament yarns span sectors such as medical, industrial, transport, engineering and protective clothing. Despite this variety of products, there is one fundamental requirement which is common to all: the absolute need for yarn evenness, measured to close tolerances, to ensure that the functional and aesthetic properties of the finished article achieve the high quality standards that customers demand.
-
Product
Bench top Dielectric Withstand tester
HYPOT III
-
RS-232 Interface available for automated controlPatented SmartGFI® functionPatented CAL-ALERT® functionComes complete with a test box for products terminated in a line cordPatented VERI-CHEK® functionStorage of up to 10 setups with 3 steps per setupBuilt-in security settingsDigitally controlled arc detection systemNo load setup of trip current and output voltageElectronic ramping (up & down)Built-in adjustable continuity testInterconnection to HYAMP® III to form complete test system
-
Product
Loop / PFC Testers
-
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2715 is a loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
Product
AC Hipot Tester
-
KV Hipot Power Test Equipment Co.,Ltd
The Hipot tester is a nondestructive test which is a effective way to determine the insulation strength for electric equipment.
-
Product
Multifunction Tester
EASYTEST
-
EASYTEST carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
In-Circuit Tester
IP-5000, IP-5300
-
The IP-5000 series is a space-saving high-speed board inspection device with a compact design.
-
Product
Light Meters & Testers
Digital Light Meter
-
*Measures incandescent, fluorescent, metal halide, high-pressure sodium and halogen lamp output*Color and cosine-corrected for enhanced accuracy*Measures up to 50,000 lux*Peak and data hold means no lost measurements
-
Product
EMC Testers
-
The KES7000 System is a conductive immunity test system that is fully compliant with ISO7637-2 and ISO7637-3, international standards for EMC testing required for automotive electronic components. This system consists of the KES7700 Series Transient Surge Tester, KES7400A Series Voltage variation simulator and KES7100 application software dedicated to the KES7000 system. This product configuration supports JASO standards and the special test requirements of car manufacturers with options or custom orders.
-
Product
Battery Management Systems
-
A BMS is the intelligent component monitoring and managing any lithium-ion battery pack. It is the brain behind the battery and has a key role in its levels of safety, performance, charge rates, and longevity.
-
Product
LED Testers
-
PeakTech Prüf- und Messtechnik GmbH
An extremely practical component tester for LEDs and other components. The device outputs an automatically raised output voltage between 0 to 300 V DC, which adapts to the connected load so that the sensitive components are not destroyed. Particularly suitable for the service and repair workshop.
-
Product
Reciprocating friction and wear tester.
-
This testing machine is used to evaluate surface conditions such as friction faces of materials by measuring the frictional force.
-
Product
Turns Ratio and Phase Tester
SS310
-
Turn ratio meter is a reliable test instrument used for product inspection and sample analysis in the manufacture of transformer, radio and TV set or relative scientific research units.
-
Product
Scienlab Battery Test System – Pack Level, 110 KW Compact Version
SL1710A
Test System
Keysight’s SL1700A Scienlab Battery Test System – Pack Level Series allows to realistically emulate the environment of the future battery pack application in order to test the high-power battery pack comprehensively and improve its functions and safety. The growing demand of e-mobility increases the need of vast battery test labs for EV battery development. Keysight developed the SL1700A Series to accelerate the development and validation of batteries. It offers a voltage range of up to 1500 V and power options between 100 and 300 kW including a Performance Bundle to increase the power up to 330 kW. The new high-voltage SiC (silicon carbide) technology provides a high energy efficiency on a small footprint and helps to minimize your operating costs.
-
Product
Particle Counter Emissions Tester
PARTICLE COUNTER | VP 135046
-
Maschinenbau Haldenwang GmbH & Co. KG.
With the PARTICLE COUNTER emission tester, you can really count every particle. Compact, rugged design, clearly readable display, rapid readiness for measurement and precise measurement results are the distinguishing features of the MAHA particle counter.
-
Product
Brinell Hardness Tester
KB Series
-
Newage Testing Instruments, Inc.
The Newage KB Series is a popular, manually-controlled Brinell hardness tester that meets ASTM E-110. This lightweight, portable tester is ideal for virtually any size or shape of metal specimen.
-
Product
Durometer - Shore Hardness Tester
-
Qualitest provides quality control departments and research laboratories with an extensive range of top quality Durometer and hardness Tester for accurate hardness determination on all natural and synthetic rubber products and soft elastic materials, plastics, acrylic glass, acetates, casting resin, polyester, thermoplastics, PVC, neoprenes, hardboards, wood, leather, fruits and much more. Our products provide the highest precision (normally 0.5% or better), quality and craftsmanship, durability, “yet require” almost no calibration in many years after the purchase. Our designs are engineered so that the Durometer stays precisely within the standard requirements. Qualitest Durometers are referred to as the “Swiss watches” among other products on the market. Investing in our line of Durometer is a guarantee of accuracy and assurance for many years of operation.
-
Product
Upgraded Probe Tester with AC/DC-A.
SK-6597
-
Current measurement up to AC / DC 400mA.Penlight and backlight LCD.
-
Product
Partial Discharge Tester
19501-K/19500
-
Chroma 19501-K partial discharge tester combines hipot test and PD (partial discharge) detector functions in one instrument. The device is capable of a maximum 10kV AC output with leakage current measurement range of 0.01uA and a minimum partial discharge detection of 1pC. The tester is specifically developed to test high voltage semiconductor components and high insulation materials.
-
Product
Leakage Current Clamp Tester with Bluetooth
M-1141XR
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Waveform display is possible with connection to a smartphone・Measurement data is to be accumulated in the server, and it is available for graph and CSV output・Auto 5-range : AC 30mA / 300mA / 3A / 30A / 300A・CT inside diameter : φ40mm・Minimum resolution : 0.01mA・Maximum value hold / Data hold function available・Band path filter with center frequency (fo = 55Hz)・Compliant with EN 61010, CAT-III 1000V / CAT-IV 600V・With backlight
-
Product
Motor Tester
-
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
Dual Station Loaded Motor Tester including Automatic Shaft Engagement, Automatic Bar Code Scanners, Full Spectrum Vibration Analysis (8 bands) with Automatic Accelerometer Placement and Reject Printer.
-
-
Product
Standard 0.49 (13.89) - 2.50 (70.87) Battery Probe
CP-4L
Battery Probe
Current Rating (Amps): 10Average Probe Resistance (mOhm): 25Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 60Full Travel (mm): 1.52Recommended Travel (mil): 40Recommended Travel (mm): 1.01Overall Length (mil): 311Overall Length (mm): 7.90Overall Length Remark: Overall length does not include tail.
