Fuse
-
product
Socket Tester
*Power supply from mains : 200-230V AC*Transmit AC signal through concrete walls; Shielded / armored cable*Internal fuse protection
-
product
Wireless Connectivity Digital Multimeter 4000 Count / NCV / SPT and with super bright LED torch
MS-WP4DMM2
This is a Palm Size external wireless connectivity Digital Multimeter integrated with 4000 Count, True RMS auto and manual measurement. Additional advantages with super bright white LED torch / flashlight and replaceable fast blow fused test leads.
-
product
Analog Insulation Tester
SAIT200
Over voltage CAT. 600V. Battery operated. Solid state circuitry. Automatic circuit discharge. Color coded scale. Fuse protected : Fast blow 0.5A 250V
-
product
Digital Multimeter
6410 DM
Standard Electric Works Co., Ltd
● 3000 counts with a maximum display of 2999.● Angled display design helps the user to identify the reading of value easier.● Auto scanning function for AC/DC voltage, and current.● Auto ranging.● Range change function.● Continuity check.● Diode & Capacitance measurement.● Data hold function.● Low battery indication.● Over range indication.● Fuse protection.● Special hook design used to hang the meter for ease of use.
-
product
Enlarge Environmental Chamber
REXMED REC-450
MOD. REC-450, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,644 Watts, 12,433 BTU/hr, 3,140 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L60 X W80 X H85cm, Capacity: 408L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
product
Single-Wavelength Fused Bi-conical Taper 1×N splitter (FBT Splitter)
PON-POS-1
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai single-wavelength Fused Bi-conical Taper (FBT) 1×N star optical fiber splitter is the series connection of N-1 pieces of 1×2 splitter. The bandwidth of +/-40nm under 1310nm, 1490nm or 1550nm makes the splitter meet the requirement of ratio accuracy. And it has feature of low additional loss and low polarization sensibility loss.
-
product
PXI Prototyping Module, 2-Slot, 78-Pin D-Type
40-225A-402
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
High Voltage Phasing Sticks
9007KB Series
Shanghai Beha Electronics Co., Ltd.
*Important applications include checking voltage fuses, testing for correct phase connections, and for absence of high voltage on deenergized lines or apparatus.*measuring ranges from 6.6kV up to 44kV systems*Fiberglass is of hot stick quality and tested to IEC specs (100kV/300mm for 1 min). All front end (resistors) are encapsulated.
-
product
Fiber Fusion Splicer
Shenzhen Sharingtek Communication Co., LTD
Fusion splicing is the act of joining two optical fibers end-to-end. The goal is to fuse the two fibers together in such a way that light passing through the fibers is not scattered or reflected back by the splice, and so that the splice and the region surrounding it are almost as strong as the intact fiber.
-
product
Deluxe DMM w/Amp Shutters
582
*Huge 2 inch LCD Display, easy to see from across the room *Display is backlit for use in Dark Spaces *Amp Shutters prevent mistaken operation, improve safety and saves fuses by blocking unused amp jacks! *Great Meter for Electrical Trouble Shooting *11 Test Functions, 33 Test Ranges *Measures Temp in Both F and C, Probe Included *Desireable 20 Amp Test Range *Modern Design, the Protective Holster is Built-In *Data Hold *Carrying case, Test leads, Temp probe, Instructions and Battery included
-
product
Cable Locators
We have cable length meters, locators and fuse finders for electrical, data network and telecommunication applications.
-
product
Fused WDM Module（1310/1550nm）
Flyin Optronics’Singlemode wavelength division multiplexer WDM 1310/1550 1X2 2X2 combine or separate light at different wavelengths. They offer very low insertion loss, low polarization dependence, high isolation and excellent environmental stability. These components have been extensively used in CATV, WDM networks, Fiber sensor and fiber optics instrumentation.
-
product
Power Capacitors with Protection Filter
CPFVF / CPMVF
Lifasa - International Capacitors, SA
The capacitors of the CPFVF and CPMVF series are formed by a power capacitor, an antiarmonic protection reactance and fuse or magnetothermic protection. These capacitors are specially designed for the fixed compensation of transformers in networks with a high level of harmonics.
-
product
Telecomunication & Electrical Insolation- Continuity-Voltage-MOV Tester(LCD Display)
1165IN
Standard Electric Works Co., Ltd
● Measures insulation (MΩ), Continuity (Ω) , AC and DC voltage● Six insulation test voltages (DCV): 50V, 100V, 125V, 250V, 500V, 1000V● 68x34 mm (2.677x1.338 inch) large LCD● Function rotary switch design for easier operation● Intuitive operation for users● User friendly interface● Auto ACV/DCV detection● Audible voltage warning● DAR/PI indication● Backlight function● Automatic circuit discharge● Test insulation at rated voltage into a 1mA load● Auto ranging● Fuse protection● EnerSave function● MOV test function
-
product
Analogue (1kV below) Insulation Tester
4132 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on "low ohms" : 3Ω & 500Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600 Vac.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Designed for meet international standards.● Supplied with high quality test leads.● BS 16 edition.
-
product
Wires and Pipe Locator
LKZ-720
*Detection of wires and cables (live or not)**detection of cables in ceilings, walls and floors,**detection of breaks in cables,**tracing cables in building installation,**locating power points and switches in buildings,**locating short circuits between leads,**tracing shielded cables,**tracing cables in metal ducts.*Identification of fuses on the distribution board.*Tracing underground cables.*Tracing conductive water and heating pipelines.*Non-contact detection of live cables.
-
product
Analogue (1kV below) Insulation Tester
8031 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on “low ohms” : 2Ω & 20Ω.● AC voltmeter with linear scale up to 600 Vac.● 200mA short circuit current for continuity.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Supplied with high quality test leads.● BS 16 edition.
-
product
PXI Prototyping Module, 1-Slot, 50-Pin D-Type
40-225A-501
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
Whattmeters
.Monophase and triphase Balance measures.Widerband power measure up to audio frequency .Small power measure.Connection and operation simplicity.Accuracy:better than 2% at the full current and voltage scale .Protection against over-currents by fuses .Over current and over voltage indictor
-
product
Field Master 3 Electric Fence Charger
FM-3
Power to stop the most stubborn stock! For small to medium pastures. The all new low impedance model for small to medium pastures features advanced solid state circuitry. Shocks through wet weeds and brush. New color coded fence and ground terminals. Red to the fence and Black to ground. Fuse protection, with built-in lightning arresters. Full 3 year warranty covers damage caused by lightning.
-
product
SparkFun GNSS-RTK Dead Reckoning Breakout
ZED-F9K (Qwiic)
The SparkFun ZED-F9K GNSS Breakout is a high precision, sensor fusion geospatial board with equally impressive configuration options and takes advantage of u-blox's Automotive Dead Reckoning (ADR) technology. The ZED-F9K module provides a highly accurate and continuous position by fusing a 3D IMU sensor, wheel ticks, a vehicle dynamics model, correction data, and GNSS measurements.
-
product
Digital Auto Multi-Meter
This Digital Auto Multi-Meter (DAMM) was designed solely for Automotive Technicians for troubleshooting all electrical problems encountered in the vehicle. Be it a 6V, 12V or 24V system it can be used to check Amps draw directly on the fuse (Mini, ATC or Maxi Fuses) without having to remove it and measure parasitic drain current using the parallel method at the fuse box.
-
product
Switching Power Supply
NS-1230M
Compact size Short circuit and over voltage protection Output power rated at continuous service Binding post output terminals Precision regulation of output voltage Lowe peak-peak ripple of less than 0.3% External fuse access High surge capacity Heavy duty metal cabinet with power coating LED Backlight
-
product
Analogue (1kV below) Insulation Tester
1652 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on “low ohms” : 3Ω & 500Ω.● AC voltmeter with linear scale up to 600 Vac.● 200mA short circuit current for continuity.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Supplied with high quality test leads.● BS 16 edition.
-
product
Pocket Size Analog Multimeter
HH2708
Basic Accuracy 4.0%. 5 Functions / 14 Ranges. Voltage test up to AC500V and DC500V. Current test up to 250mA. Resistance test up to Ω x 1K. Test Batteries 1.5V and 9V. Power: 1 x 1.5V "AA" battery. Fuse: 0.5A, 250V type Φ 5 x 20mm
-
product
Digital ELCB (RCD) Tester
2712 EL
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2 Lines × 16 characters LCD.● Very low consumption.● 50Hz and 60Hz operation.● Menu-driven.● Accurate digital readout of disconnection time.● Automatic data hold function.● Over temperature protection.● Over voltage protection.● Fuse protection.● Zero crossing circuitry permit testing at 0° or 180°.● Disconnection phase polarity shown on LCD display.● Auto off and off override.● Polarity trip indicator (positive or negative phase)● Wiring polarity indicator.● Measure voltage between Line and Earth before testing.● Frequency measurement indication.
-
product
Circuit Breaker Identifiers
190 CBI
Standard Electric Works Co., Ltd
● 190 CBI is an easy tool to find the circuit breaker or fuse supplying electrical power to an outlet or lighting fixture. Just plug the transmitter into the outlet.● Use the receiver to scan the circuit breaker panel box. An audible tone will be clearly heard when the right circuit breaker is scanned.● The plug of transmitter is changeable. The plug of transmitter could be changed for customers' requirement from different countries.
-
product
6-24V Heavy Duty Circuit Tester
1653
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 24V systems. Use on fuses, test connections and find short circuits quickly and easily. Available for checking on lights, starters, alternators, cooling and heating components, radios and relays.
-
product
Electronic Cards
Our product range includes a wide range of PDBC Relay Card, Local Remote Selector Card, Monitor Card and Fuse Failure Relay Card.
-
product
Fault Locator
BIDOYNG
BIDOYNG fits into existing LV fuse positions using two LV fuses in parallel, creating a robust single-shot auto-recloser. The primary fuse carries the load current until a fault causes it to operate. Then, after a user programmed delay, the secondary fuse is switched in and the network re-energised without customer interruption.
