Sound Wave
-
product
Sound Level Meters
A sound level meter is used for acoustic (sound that travels through air) measurements. It is commonly a hand-held instrument with a microphone. The diaphrahm of the microphone responds to changes in air pressure caused by sound waves.
-
product
Ultrasonic Leak Detector
ULD-420
When equipment begins to fail due to an air or gas leak or vibration, or electrical discharge, the leakage point emits an ultrasonic sound wave that is above the natural range of human hearing. The ULD-420 Ultrasonic Leak Detector converts this ultrasonic sound into a signal that can be used to pinpoint the exact location of the equipment failure. When working in unpressurized systems or the pressure is not sufficient enough to detect or verify a leak with the Receiver alone use the Transmitter.
-
product
Split Type Ultrasonic Level Gauge
HR9100D
HighReach Measuring & Controlling System Co.,Ltd
1. Stable and reliable / We select high-quality modules and key components from the power supply part to select high-stability and reliable devices, which can directly initiate imported instruments. 2, patented technology / one ring patented sound wave intelligent technology software can Intelligent outgoing analysis without any debugging and other special steps, this technology has the function of dynamic thinking, dynamic analysis 3, high precision / sound wave intelligence owned by our company The patented technology greatly improves the accuracy of the ultrasonic level gauge, the Liquid level accuracy reaches ±0.2%, can resist various interference wavesThe instrument is a non-contact instrument, not Direct contact with liquid, so the failure rate is low. The instrument provides a variety of installation methods, users can use this . The Instrument Manual Calibrate to 5. The Protection of The Level of Multiple Protection / IP67 & Instrument Reaches; INPUT and Output Lines All have have Lightning Protection and Short Circuit Protection.
-
product
Ultrasonic Rotary Mechanisms For High Speed Testing Of Round Bar And Tubular Products
ECHOMAC® ULTRASONIC ROTARIES
High-speed Ultrasonic (UT) Systems enable a full volumetric examination of materials and are designed to detect surface, subsurface, internal and dimensional flaws. This type of testing utilizes high-frequency sound waves that are transmitted throughout the material being tested in order to conduct a thorough inspection.
-
product
Ultrasonic & Mass Flow Meters
GAOTek offers high quality, affordable, secure and accurate Ultrasonic Flow Meters for sale to the United States, Canada and globally. Ultrasonic Flow Meters often have a sending and a receiving transducer for measuring the velocity of fluids to accurately calculate the flow of volume in a pipe by using sound waves, acoustic waves or vibrations with a frequency of >20 KHz. GAOTek offers a variety of top-notch Ultrasonic Flow Meters designed for different environments, from wide pipes to an all liquid environment, such as sea water, oil, sewage, alcohol, et al. GAOTek’s easy to use Ultrasonic Flow Meters come with a built-in printer and a built-in data logger. They provide accurate readings and have an accuracy rate of ±1% at rates greater than 0.2mps. They also offer multi-language menu selections, long lasting battery life for continuous usage, large LCD screens, and a huge storage.
-
product
Ultrasonic Leak Detector
ULD-410
When equipment begins to fail due to an air or gas leak or vibration, or electrical discharge, the leakage point emits an ultrasonic sound wave that is above the natural range of human hearing. The ULD-410 Ultrasonic Leak Detector converts this ultrasonic sound into a signal that can be used to pinpoint the exact location of the equipment failure.
-
product
Ultrasonic thickness gauge
The frequency range of sound that can be heard by the human ear is about 20Hz to 20KHz, and sound waves with higher frequencies are called ultrasonic waves. In general ultrasonic flaw detection equipment, 5MHz is often used in the range of 1MHz to 20MHz as standard.
-
product
Hydrophones
Piezo is a critical element in producing a hydrophone for military and commercial underwater listening applications. Hydrophones utilize piezoelectric elements to detect sound pressure waves produced by underwater vessels, animals, and the environment. Hydrophones must have a flat frequency response that is proportional to the magnitude of the sound pressure wave. CTS piezo elements provide this critical function in hydrophones by providing excellent frequency response and high coupling factors necessary in hydrophone applications. CTS materials provide excellent electrical properties for hydrophone applications while allowing the ability to form the piezo element to the desired mechanical structure for the hydrophone.
-
product
Non-Destructive Testing
Piezoelectric ceramic materials are the active component in nondestructive testing transducers. The material is driven with an ac signal to generate an ultrasonic sound wave that is coupled into an object. The ultrasonic wave is reflected back to the transducer when it encounters a change in density in the material caused by a crack, porosity, or other object with a different density.
-
product
Flaw Detectors
GAOTek flaw detectors are designed as high-quality devices that provide accurate detection whilst delivering ease of use towards testing and monitoring. These detectors examine a material by passing sound waves at high frequencies through it and are used for applications that require ultrasonic testing. They are compact, easy to carry and portable devices that allow the user to work in complex conditions and circumstances, and available for purchase in the United States, Canada and globally.
-
product
Integrated Ultrasonic Level Gauge
HR9100T
HighReach Measuring & Controlling System Co.,Ltd
The circuit design selects high-quality power module components from the power supply part to select high-stability and reliable devices, which can completely replace the same type of imported instruments. The patented sonic intelligent technology software can perform intelligent echo analysis the debugging and the any OTHER Special the without Steps. This Technology has Dynamic Thinking at The Functions of the Analysis and Dynamic. Sound Wave at The Patented Technology of Our Company Makes at The Accuracy of at The Instrument Greatly Improved, at The Precision Liquid Level Reaches 0.25%, and IT CAN Resist various kinds of interference waves. This instrument is a kind of non-contact instrument, which does not directly contact with liquid., the instrument has a variety of installation methods. The user can use this manual to calibrate the instrument. All input and output lines Of the instrument have lightning protection and short circuit protection.
-
-
product
Ultrasonic Concrete Testing
This category comprises the range of instruments that use sound or stress waves in order to determine the properties of concrete and other materials non-destructively. The first and most widely used System is our V-Meter, which utilizes the ultrasonic pulse velocity method for evaluating construction materials in the field. Transducers are available for a variety of frequencies from 24 KHz to 500 KHz. This unit has also been modified to suit the special needs of ceramics users and can be found as the Ultrapulse. The PIES, our revolutionary Portable Impact-Echo System, is an advanced instrument for non-destructive detection of flaws and defects in a variety of civil infrastructures ranging from bridges, parking structures and buildings to dams, piles, tunnels, tanks and marine structures.
-
product
Medical Ultrasound
Piezo elements form an essential component in medical diagnostics. Medical Ultrasound uses high-frequency sound waves to look at organs and structures inside the body. Medical professionals use medical ultrasound to view internal organs and during pregnancy to view the fetus. CTS provides both monolithic and composite piezoelectric elements used in medical ultrasound applications.
-
product
Assesses Nodularity In Ductile Iron Cast Automotive Components
ECHOMAC® Velocity Measurement
Variations in Nodularity, a type of graphite structure that can develop during the production process, can attenuate the velocity of sound waves passing through the automotive component being tested. Echomac VM measures the sound velocity and, using known limits, reports whether the part is acceptable.
-
product
Ear Simulator
BO1028
The BO1028 Ear Simulator is a special coupler for microspeakers or earbuds that has been designed to be compliant with ATU-T P.57 and IEC 60318-1. While mics in our BP1090 couplers receive sound waves the way they travel through air, the dual compartment chamber of the BO1028 is designed to modify sound pressure so that the mic receives air vibrations the way a human ear drum would receive them.
-
product
Integrated/Separated Explosion-Proof Ultrasonic Level Gauge
HR9100E
HighReach Measuring & Controlling System Co.,Ltd
1. Safety / use of die-cast aluminum alloy waterproof, explosion-proof shell; the explosion-proof grade of the instrument reaches Exd (ia) IIBT4 2. stable and reliable / we choose high-quality module key components from the power supply Part of The Circuit Design Stable and Reliable Devices CAN Completely Replace imported Instruments. 3. Patented Technology / Ultrasonic Intelligent Software CAN with Carry OUT Intelligent echo Analysis, the without the any the debugging and OTHER Special Steps, the this Technology has The function of Dynamic Thinking, Dynamic Analysis 4. High precision / sound wave intelligent patent technology owned by our company, so that The accuracy of the ultrasonic level gauge is greatly improved, the liquid level accuracy reaches 0.3%, it can resist various interference waves, the failure rate is low, the installation is easy, and the maintenance is easy. The instrument is a non-contact instrument and does not directly contact with liquid. Users can use this manual to calibrate the instrument. 6. The protection level of multiple protection/instrument reaches IP65; all output and input lines have lightning protection and short circuit protection.
-
product
EVISION Obstacle Detector
MS 1528
Obstacle Detector is a distance-measuring system based on ultrasonic sound utilizing the LPC2364FBD100. The system transmits a burst of ultrasonic sound waves towards the subject and then receives the corresponding echo. The LPC2364FBD100 integrated analog comparator is used to detect the arrival of the echo to the system. The time taken for the ultrasonic burst to travel the distance from the system to the subject and back to the system is accurately measured by the LPC2364FBD100. Assuming the speed of sound in air at room temperature to be 1100 ft/s, the LPC2364FBD100 computes the distance between the system and the subject and gives the information to buzzer. The minimum distance that this system can measure is eight inches and is limited by the transmitter’s transducer settling-time. The maximum distance that can be measured is 2 meter. The amplitude of the echo depends on the reflecting material, shape, and size. Sound-absorbing targets such as carpets and reflecting surfaces less than two square feet in area reflect poorly. The maximum measurable range is lower for such subjects. If the amplitude of the echo received by the system is so low that it is not detectable by the Comparator. This system is mainly used to replace normal sticks for the visually impaired (blind) peoples. This unit has standard USB 2.0 for mobile interface and has android application for user interface
-
product
Infrasonic Array
Geosonic
An Infrasonic Array works like a sonic antenna, it is able to detect the magnitude and the source of sound waves. The Geosonic array is able to detect also pressure waves that the human ears can’t hear. A typical pressure wave is that generated by an explosion or by any physical phenomena (natural or human created) that generates an air pressure wave, which means that the Geosonic array can be used to detect a lot of phenomena, like:
-
product
Precision Marine Geodetic Systems
Using leading-edge "Broadband Acoustic Spread Spectrum Technology", accurate sound wave traveling time between LinkQuest's subsea precision transponders and surface station can be measured. When the system is integrated with a Kinematic GPS, motion sensors and a gyro on the surface vessel or undersea vehicle, sub-centimeter acoustic positioning can be achieved.
-
product
Ultrasonic Liquid Level Difference Meter
HR9100L
HighReach Measuring & Controlling System Co.,Ltd
1. Stable and reliable / We select high-quality modules and key components from the power supply part to select high-stability and reliable devices, which can directly initiate imported instruments. 2, patented technology / one ring patented sound wave intelligent technology software can Carry out intelligent echo analysis without any debugging and other special steps, this technology has the function of dynamic thinking, dynamic analysis 3, high precision / sound wave intelligence owned by our company The patented technology makes the accuracy of TS-CJ ultrasonic level gauge greatly Improved, the liquid level precision reaches 0.3%, can resist various interference wavesThe instrument is a non-contact type. The meter does not directly contact the liquid, so the fault rate is lower. The meter provides a variety of installation methods, and The user can use this manual to calibrate the meter. 5. The protection level of multiple protection/instrument reaches IP65; all output and input lines have lightning protection and short circuit protection.
-
product
Ultrasonic Flaw Detector
Shenzhen Graigar Technology Co.,Ltd.
Flaw detection is the most commonly used technique among all the applications of industrial ultrasonic testing. Generally, sound waves of high frequency are reflected from flaws and generate clear echo patterns.
-
product
Non-metallic Pipe Locator
NPL-100
The NPL-100 is a sophisticated instrument for locating non-metallic water pipelines.Using a vibrator attached to the outlet of a fire hydrant or to pipe fittings, the NPL-100 sends a sound wave through the water in the pipe.
-
product
PXIe-4492, 204.8 kS/s, 113 dB, 2 Gains, 0.5 Hz AC/DC-Coupled, 8-Input PXI Sound and Vibration Module
781490-01
204.8 kS/s, 113 dB, 2 Gains, 0.5 Hz AC/DC-Coupled, 8-Input PXI Sound and Vibration Module - The PXIe‑4492 is designed for sound and vibration applications. With 24-bit analog inputs and IEPE constant current signal conditioning, the module is ideal for making precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. The PXIe‑4492 delivers simultaneous sample on all channels. In addition, it includes built-in antialiasing filters that automatically adjust to your sample rate, software-selectable input gains, and TEDS smart sensor support for error-free setup. Common applications include noise, vibration, and harshness (NVH) analysis; large microphone arrays; and dynamic structural test.
-
product
PXIe-4463, 51.2 kS/s, 2-Output PXI Sound and Vibration Module
783086-01
The PXIe‑4463 offers high dynamic range and THD+N for audio, acoustic, and vibration applications. It provides the high precision and dynamic range necessary for the most stringent audio generation requirements in a modular form … factor. The PXIe‑4463 contains two 24-bit digital‑to‑analog converters to allow for fully differential simultaneous generation. Complete with three gain ranges, the PXIe‑4463 can generate current with programmable, per channel output configurations. The two timing engines allow you to perform multisample-rate applications on a single module and independently start and stop channels on a single module.
-
product
NI-9234 and cDAQ-9171 USB Sound and Vibration Measurement Bundle
865664-01
NI-9234 and cDAQ-9171 USB Sound and Vibration Measurement Bundle - The USB Sound and Vibration Measurement Bundle with NI-9234 and cDAQ-9171 includes the NI-9234 C Series Sound and Vibration Input Module and the cDAQ-9171 CompactDAQ Chassis for sound and vibration measurements. This bundle provides a portable, USB-based sensor measurement system that helps you measure signals from integrated electronic piezoelectric (IEPE) and non IEPE sensors such as accelerometers, tachometers, and proximity probes. The included NI-9234 features 4 channels with built-in anti-aliasing filters that automatically adjust to your sample rate. Additionally, when used with NI software, the bundle provides processing functionality for condition monitoring such as frequency analysis and order tracking.
-
product
Ultrasound Measurements
Is sound waves with frequencies higher than the upper audible limit of human hearing. Ultrasound is no different from 'normal' (audible) sound in its physical properties, except in that humans cannot hear it. Ultrasound devices operate with frequencies from 20 kHz up to several gigahertz.Ultrasonic devices are used to detect objects and measure distances. Ultrasound imaging or sonography is often used in medicine. In the nondestructive testing of products and structures, ultrasound is used to detect invisible flaws.
-
product
NI-9230, 3-Channel, 12.8 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module
783824-01
3-Channel, 12.8 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module - The NI‑9230 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The NI‑9230 is also compatible with smart TEDS sensors. The NI‑9230 incorporates software-selectable AC/DC coupling, IEPE open/short detection, and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti-aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking.
-
product
NI-9232, 3-Channel, 102.4 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module
784397-01
3-Channel, 102.4 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module - The NI‑9232 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The NI‑9232 is also compatible with smart TEDS sensors. The NI‑9232 incorporates software-selectable AC/DC coupling, IEPE open/short detection, and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti-aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking.
-
product
NI-9234, 4-Channel, 51.2 kS/s/channel, ±5 V, C Series Sound and Vibration Input Module
779680-01
4-Channel, 51.2 kS/s/channel, ±5 V, C Series Sound and Vibration Input Module - The NI‑9234 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The NI‑9234 is also compatible with smart TEDS sensors. The NI‑9234 delivers a wide dynamic range and incorporates software-selectable AC/DC coupling and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti-aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking.
