Circuit Board
-
Product
Analog Multiplexer Board
104-AIM-32 PC/104
-
The 104-AIM-32 is an analog signal multiplexer conforming to the PC/104 standard. The card will multiplex and condition 16 differential or 32 single-ended analog signals before passing them to an analog-to-digital converter card like the 104-AIO12-8. A system may comprise one to seven of these cards in tandem with one 104-AIO12-8 A/D converter board. The 104-AIM-32 card may be used as part of a large data acquisition system. The 104-AIM-32A Kit consists of one 104-AIM-32 and one 12-bit 8-input A/D board.
-
Product
Burn-In Boards
-
Manufacture of burn-in boards since 1976. Established for more than 40 years in the market, Trio-Tech is recognized and is an approved global supplier to all major semiconductor companies. Trio-Tech has the capability to design and manufacture boards for all system types, with solutions available for many test conditions, Including HTOL, PTC, HAST and 85/85.
-
Product
Test Board For SFP+ / SFP28 Transceiver
ESFP280
-
The OPTELLENT ESFP280 is a cost-effective and convenient test board for testing SFP/SFP+/SFP28 optical transceivers in R&D and manufacturing environments. The ESFP280 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The ESFP280 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
Product
Current Measurement Board
MS 1814
-
*Maximum DC Voltage Rating: 15V to 75V*Maximum DC Current: 5A*Output Voltage per 1A: 1V*Maximum AC Current: 5A*Operating Temperature: 0°C to 55°C*Storage Temperature: -20°C to +65°C*90% Relative Humidity (Non-condensing)*No. of DC Current Channels: 9*No. of AC Current Channels: 4nos*Maximum AC Voltage Rating: 230VAC*Channel Selection: Through 16 CH Analog MUX*Measurement Error Over Full Temperature Range: 5%*Type of Output: Proportional voltages*Maximum Voltage Drop across Series Resistor Full Scale Measurement: 0.05VDC
-
Product
Demonstration Board
SAMPULSE20x2
-
The SAMPULSE20x2 is a demonstration board for the Furaxa SiGe3 30GHz sampler/pulser IC. The SIGe3 IC is a dual channel sampler pulser chip, and the SAMPULSE20x2 demonstration board contains two 2.4mm combined TDR input/output connectors, one to each sampler/pulser channel in the IC. The SiGe3 IC's two sampler outputs are then sent to to two SMA jacks, the first outputting the sample taken on the rising edge of the sampler clock, and the second containing the sample taken on the falling edge of the sampler clock. The sampler clock input, which must be a square wave, may be set to any frequency from 5MHz to 1GHz, causing the board take two pairs of samples (one on each clock edge) at rates from 5 million to 1 billion per second. A pulser clock input, which may be set to any frequency from 5MHz to 2GHz, and MUST be a square wave (preferably differential) with rise time under 100pS, causes the board to produce concurrent pulses on both of the SiGe3's I/O pins, which produce near-concurrent pulses at the two 2.4mm sampler/pulser TDR input/output connectors.
-
Product
ISA Isolated Digital I/O Boards
ISO-P64
-
The ISO-P64 has 64-channel isolated digital input board, arranged into four isolated banks. Each input channel use a photo-coupler input which allows either internal power supply or external power selected by jumper. Isolated input channels 0~15 are designed into group A, channels 16~31 are designed into group B, Isolated input channels 32~47 are designed into group A, channels 48~63 are designed into group B. The power supply of the input port may use the external power or the power from the PC side using DC to DC converter. The board interface to field logic signals, eliminating ground-loop problems and isolating the host computer from damaging voltages. The ISO-P64 has one 37-pin D-sub connector and one 40-pin header. The 40-pin to D-sub 37 flat cable is used to fix with the case. The user can connect the digital signal through the second D-sub connector. Each D-sub connector contains 16 inputs channel and 16 output channel.
-
Product
Breakout Boards
-
Breakout your Raspberry Pis and Arduinos with this broad selection of versatile breakout boards! Engineered to help you realize your robotics, GPS and altitude sensing projects as well as servo and touch screen interfacing, you''ll find many uses for these high-quality boards, most of which are manufactured in house at Adafruit!
-
Product
Pulse Generation Measurement Board
MS 1806
-
*TTL Pulse measurement channels (Timers / Counters) 18 Channels*TTL Pulse Generation - 12 Channels*The Pulse Generation Frequency from 10Hz to 40MHz*The no. of pulses controlled from 1 to 255 pulses*All Channels are compatible with 5V TTL / CMOS*All the pulse input and the output signals driven through Pin Driver*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
CPCI ARM LPC3250 Board
MS 1513
-
- 32 Bit ARM LPC3250 Processor (256KB SRAM)- 133MHz External Bus Speed and 266 MHz internal CPU Speed- 32 Bit, 33MHz CPCI Bus, 6U Form Factor- External memory ( Flash – 2 MB, RAM - 512 KB, DPRAM – 128KB)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports, 4 RS422 Serial Ports- M Module Interface- 6U board compatible with CPCI & PXI backplanes- High Speed Logic Device- Hot Swap Feature- Front Panel and Rear IO Interface- External Bus through Rear IO- Reception of 3Kbytes within 2ms through Ethernet- Board Dimension is 160mm x 233.35mm- Power Requirements: +3.3V, +5V and +/-12V- Board Dimension is 160mm x 233.35mm- Board has Rear IO interface- Ethernet, JTAG, RS232, USB connectors at front side- BSPs and Driver software for Windows and Linux OS
-
Product
CableEye Tester Calibration Verification Board | Cable & Harness Tester
CB50
-
Populated with precision resistors, it allows users to determine empirically whether the tester requires calibration. The CB50 may be used on all CableEye models. The CB50 is intended for periodic verification of tester calibration. To ensure that resistance measurements remain accurate, CAMI recommends yearly calibration. However, depending on environmental conditions and usage, testers may need calibrating more or less frequently.
-
Product
Heavy-Duty Circuit Tester With Grounding Adapters
30610
-
Heavy-duty circuit tester with multiple options for connecting to a ground source. Long, 12’ cord has a quick coupler to securely connect clamp or power outlet plug. Large, strong clamp connects securely. Power outlet plug can always be used to provide ground in the cabin. For testing circuits up to 12 volts.
-
Product
Interface Board, Compact, 8:1 Ethernet RJ45
40-965-907
-
Compact converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 9 RJ45 sockets. Allows the multiplexing of up to 8 Ethernet signals with speeds up to 1G bit.
-
Product
Squid Carrier Board™ Family PCI Express Carrier Board for 8 MiniPCI Express Modules
SKU-085-01
-
Squid PCI Express Carrier board for MiniPCIe modules is the first product in the Squid PCI Express Carrier Board™ family. PCI Express Carrier board was designed to expand modern motherboards that have PCI Express interface. It allows connection of up to 8 MiniPCI Express half or full-size MiniPCI Express modules to the one motherboard’s PCI Express slot.
-
Product
CPCI or PXI MIL1553B & ARINC429 Board
MS 1700
-
The 1553 Board consists of dual Redundant 1553B Channel A & B and ARINC 429 Channels (6TX and 12RX).
-
Product
PCI Multifunction Board
PCI-1602/8K/S
-
The PCI-1602/1602F series is a family of high performance and high resolution data acquisition boards for the PCI bus. It features a continuous, 100KHz for PCI-1602 (200KHz for PCI-1602F), gap-free data acquisition under DOS and Windows. The PCI-1602 family has the same hardware architecture as PCI-1802L. The PCI-1602 provides 32-channel single-ended or 16-channel differential analog inputs. Like the PCI-1802 family, the PCI-1602 series features a "Magic Scan" function, M-function, X-function, and Continuous Capture function.
-
Product
Development Board
SOM-DH7000
-
Development Board for COM-HPC® Extension Modules. COM-HPC® Extension Size E, RunBMCv1.5 260pin socket interface (A2). 1 PCIe x1 reserved for BMC add-in card (A1) Rich extension: 4 x PCIe x16, 1 PCIe x8, 1 PCIe x4, 2 PCIex1 (Gen 5).
-
Product
Single Board Computers
SBC
-
*This section contains a wide range of Single Board Computers (SBC) available in many form factors: EPIC, EBX, and much more. *These embedded Single Board Computers come in standard form factors in compact sizes with rich I/O, high flexibility, easy expansion capabilities and extended temperature options.
-
Product
Video Mirror Board
BL-MIR540-01
-
The MicroImage MIR540 is a high performance display processor capable of mirroring the video input on the X and Y axes. Each of the four selectable inputs may be individually mirrored horizontally, vertically or both. Mirroring on both axes is the same as rotating the image 180 degrees. A color bar test function is also available.
-
Product
PCI Daughter Boards
DB-8225/2 (with 2 meter D-Sub 37-pin cable)
-
Screw terminal boardusing 37 pin cable I/O ports for A-82X seriesPCI-1800 series. (16 channel single-ended or 8 channel differential)Blank padsfor break detectionlow-pass filtercurrent shut and voltage attenuation.On board cold junction circuit in analog input channel 1jumper selectable single-endeddifferential modeDimensions :118mm x 174mm
-
Product
PCI Express Multi-Function Boards
PCIe-8620
-
PCI Express, 200 kS/s High-speed, 16-bit 8/16-channel Simultaneously Sampled Analog Input Board with 4/12-channel Isolated DIO
-
Product
Intel x51 Based Boards
MS 1507
-
- General Purpose I/O Signals- RS232/422 Interface- External Bus, External Interrupts
-
Product
PMC Digital IO Board
MS 1815
-
*Bus Interface:- 32 Bit PCI Bus with PMC Interface*Speed of operation up to 66MHz*Spartan-3AN FPGA based design*128 channel digital I/O signal*Input/output ON state=3.5V to 5.0 max at -24mA*Input/output OFF state= 0.8max at 24mA*16 groups of 8 channels can be programmed as input/output*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
Product
Analog Expansion Board
MSXB 014
-
The MSXB 014 Analog Expansion Board provides 4 additional analog outputs. Up to 16 Analog Output Expansion Boards can be connected to a single DAP for a total of 64 additional output channels.
-
Product
Motion Control Terminal Board for Mitsubishi J2S-A Servo Amplifiers
DIN-814M0
-
This well-designed motion control terminal board is for the users who use Mitsubishi J2 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
Product
High Frequency Clock Divider Board
-
Alliance Support Partners, Inc.
Clock Divider is designed to divide high frequency signals, up to 2.5GHz, from 4 to 256 times. It will accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms. The clock division is controlled by 4 shunt jumpers. The circuit can be disabled and the divide by counter reset with 2 control signals. The on board regulator will accept voltages from 4.85 to 15.0V. The output is capable of driving 700mV Peak to Peak into 50 Ohms.
-
Product
ARM Computer
SYS-398S-1G-0
-
WINSYSTEMS’ SYS-C398S low power single board computer combines high performance multimedia graphics with a rich mix of industrial I/O. The NXP® i.MX 6S processor’s integrated power management provides excellent efficiency and allows operation from -40° to +85°C without active cooling. It is designed for demanding graphical applications in security, transportation, medical, and digital signage.
-
Product
Alchitry Au+ FPGA Development Board (Xilinx Artix 7)
-
The Alchitry Au+ is the "gold" standard for FPGA development boards and it's possibly one of the strongest boards of its type on the market. The Au+ substitutes a more robust & scalable FPGA chip (Xilinx XC7A100T) that allows for more complex application circuits. The number of Configurable logic blocks (LABs/CLBs), Logic Elements, and total RAM bits are all nearly 3x that of the standard Au; see "Features" for more details.
-
Product
ARM LPC2294 Based Board
MS 2500
-
- JTAG interface- Boot Flash interface- External Flash interface for data storage- External Bus interface- SPI Interface- I2C interface- Serial port interface- CAN Interface- LPC2694 based processor board- MIL1553B Bus Interface (Dual Redundancy)
-
Product
6-48V Digital Circuit Tester
1674E
-
Peaceful Thriving Enterprise Co Ltd
Checks on 6, 12, 24 and 48V systems.
-
Product
Circuit Breaker Testing Equipment
HISAC Swift
-
HISAC Swift - Circuit Breaker Operational Analyser is meant for checking the performance of the MV Circuit Breakers. The Analyser contains various intelligent measuring modules designed for measuring parameters such as contact timings of Main/PIR & Auxiliary contacts, Close/Trip Coil Current characteristics and Static Contact Resistance of R, Y & B poles simultaneously. The results can be directly viewed on the TFT touch screen display in graphical as well as numerical form. It is possible to print the graph on a built-in thermal printer or download record to PC for further analysis on CPLOT software. This all in one instrument is best suited for gang operated CBs.
