Voice Data Video
convergence of formerly separate communication technologies.
-
Product
8-CH Analog Input Module
ND-6017
Data Acquisition Module
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
PXI Data Acquisition
DAQ
Data Acquisition Module
Installation and configuration is fast and easy with standard connectors, soft front panels and Keysight connection expert. In addition, software drivers support the most common programming environments such as Visual Studio®, C, C++, Visual Basic, MATLAB® and LabVIEW™.
-
Product
Modular and Scalable Multifunction Switch/Measure Units
EX1200 Series
Data Acquisition Module
The EX1200 product family is a modular and scalable series of multifunction switch/measure units that can be configured to address a variety of applications in the mechanical data acquisition and electronic test environments.
-
Product
4/8-CH 12-Bit 1 MS/s Analog Output Multi-Function DAQ PCI Express Cards
DAQe-2500 Series
Data Acquisition Module
ADLINK DAQe-2500 series are high-speed and high-performance analog output multi-function DAQ PCI EXpress cards. The devices are able to update up to 8-CH, 12-bit analog outputs simultaneously at sustaining 1 MS/s. The reference sources and the output polarities are programmable on per channel basis, combining with the multiplying DAC architecture, ADLINK DAQe-2500 series DAQ cards can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees the CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory.
-
Product
Low-Cost 16-Bit Multi-Function DAQ Card with 2-CH Encoder Input
PCI-9221
Data Storage
The ADLINK PCI-9221 is a 16-bit high-resolution and low-cost multi-function DAQ card, with 16-CH singleended or 8-CH differential input capable of up to 250 kS/s sampling rate. In addition, the PCI-9221 comes with a 2-CH 16-bit static analog output and programmable function I/O. The software-programmable function I/O supports a variety of applications, including TTL digital I/O, general-purpose timer/counter, encoder input, and PWM output. The flexible function I/O makes the PCI-9221 the best single-board solution for combined data acquisition and simple motion control functionalities. Ideal for manufacturing, laboratory research, and factory automation, the PCI-9221 comes with all the functions you need at an affordable price.
-
Product
Analog Output Module
ND-6021
Data Acquisition Module
- Voltage Output: 0 to 10 V- Current Output: 0 to 20 mA, 4 to 20 mA- Output Isolation: 5000 VRMS- Resolution: 12-bit resolution- Accuracy: ± 0.1% of FSR (current); ± 0.2% of FSR (voltage)
-
Product
4-CH 14/16-Bit Up to 2 MS/s Simultaneous-Sampling Multi-Function DAQ PCI Express Cards
DAQe-2000 Series
Data Acquisition Module
ADLINK DAQe-2000 series products are simultaneous-sampling multi-function PCI Express DAQ cards to meet a wide range of application requirements. The devices can simultaneously sample 4 AI channels with differential input configuration in order to achieve maximum noise elimination. They also provide 2-CH 12-bit analog outputs with waveform generation capability, which can be performed together with analog input functions. If more analog input or output channels are required, multiple cards can be synchronized through the SSI (system synchronization interface) bus. This makes the DAQe-2000 series ideal for the stimulus/response test.
-
Product
Optical / Electrical Clock Recovery
N1078A
Clock and Data Recovery Unit
N1078A Optical/Electrical Clock Recovery provides standards-compliant clock recovery capabilities for single-mode optical as well as electrical signals from 125 MBd up to 64 GBd PAM4 and NRZ
-
Product
48-Ch TTL DI/O IDAQ Module
iDAQ-751
Data Acquisition Module
Hot-swappable in iDAQ systemDetachable Euro-type spring terminal connectors48-channel TTL digital I/OsConfigurable digital I/O directionIsolation protection of 60 VDCSupports buffered acquisition/update rates up to 200kHz
-
Product
Voice and Video Transcoding
-
Maintain omnichannel experience with seamless interoperability
-
Product
19" Rackmount Rugged, Fanless AIoT Platform for Real-time Video/Graphics Analytics
AVA-5600
Video Analytics Platform
- Intel® Core™ i7-7820EQ Processor and Mobile Intel® CM236 Chipset- NVIDIA Quadro® GPU MXM 3.1 Type A/B module on PCIe x164x M12 GbE with PoE, 4x USB 3.0- Rich Storage Options: 2.5" SATA 6.0 Gb/s drive bay, 1x M.2 2280 slot, 1x CFast socket- GNSS/3G/4G/WLAN support via 2x Mini PCIe slots and 2x USIM slots- MVB/CAN bus support by Mini PCIe add-on module (BOM option)- Nominal Voltage: 110VDC (EN50155 compliant)
-
Product
8AI Modbus RS-485 Remote I/O
ND-6117
Data Acquisition Module
The NuDAM modules provide direct communications with a wide variety of sensors; perform signal conditioning, scaling, linearization and conversion; can acquire measurements of temperature, pressure, flow, voltage, current; and handle multiple digital signal types broadly used in IoT and other industrial applications, such as facility monitoring, environment monitoring, and industrial process control. The new ND-6117, ND-6124, ND-6150, and ND-6160 modules feature Modbus/RTU as the best remote data transmission protocol, which provides customers a comprehensive product offering.
-
Product
USB to RS-422/RS-485 Converter
ND-6530
Data Acquisition Module
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
16-CH Digital Input Module
ND-6053
Data Acquisition Module
- Channels: 16 DI- Channels: 16 DI: Logical 0: close to GND; Logical 1: open; Effective distance: 500m- Wet contact: TTL level- Programmable input polarity
-
Product
HDD-8261, 4 TB, 6-Drive, PXI Data Storage Module
784192-01
Data Storage
4 TB, 6-Drive, PXI Data Storage Module - The HDD‑8261 in-chassis PXI Express high-speed data storage module features an onboard PCI Express SATA controller. The module fits into a PXI Express chassis, and it occupies only three PXI slots. With the HDD‑8261, you can choose between hard-disk drives (HDDs) or solid-state drives (SSDs) for increased ruggedness. It is ideal for field testing or signal recording applications. You can use this module to not only stream high-speed data, but also to easily move data between multiple test setups or supplement the PXI system controller’s storage capacity.
-
Product
Intelligent 16 Bit Data Acquisition
CPCI-AD16
Data Acquisition Module
The CPCI-AD16 module provides a 3U high performance data acquisition subsystem. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digitalfiltering, etc. Application software can be downloaded to the DSP via the CPCI interface. Instrumentation amplifiers provide over-voltage protection, gain and filtering on a per channel basis. Internal scan and trigger clocks are derived from either the CPCI bus clock or the local DSP clock. Dual 32 bit timers can programmed to pace the acquisition process. The CPCI-AD16 can also accept external scan and trigger signals from a front panel connector.
-
Product
Call Generator (Voice / Data)
-
Qosmotec Software Solutions GmbH
The Mobile Network Tester LTS is an automatic call generator, that establishes voice and data calls to and from actual mobile devices in the test system. Voice calls can be generated via the wireless PLMN network using actual mobile devices, via the PSTN network through analogue or ISDN lines or via Voice over IP. Wireless data sessions can be setup through the 3G or 4G network or over WiFi.
-
Product
Voice and Video over LTE and 5G
-
Enable scalable high-definition voice and video over LTE and 5G with industry-leading Radisys Engage Media Server.
-
Product
VOICE OF THOR
-
THOR GUARD's Voice of Thor or VOT lightning alarm system is utilized to provide a unique aubible warning pattern when the area THOR GUARD is monitoring has become susceptible to a lightning strike. Simultaneously during the hazard time, LED strobe lights can be utilized to provide a continued visible notification of the impending hazard. THOR GUARD allows for a base horn with the remotes, either electric or solar powered, being controlled using THOR GUARD’s dedicated RF system. When combined with the Guardian Emergency Notification System, a special 1-minute pattern is generated to provide for any unexpected emergency.
-
Product
64-CH 12/16-Bit Up to 3 MS/s Multi-Function DAQ PCI Express Cards
DAQe-2200 Series
Data Acquisition Module
ADLINK DAQe-2200 series are highdensity and high-performance multi-function DAQ PCI Express cards. The devices can sample up to 64 AI channels with different gain settings and scan sequences. It makes them ideal for dealing with high-density analog signals with various input ranges and sampling speeds. These devices also offer differential mode for 32 AI channels in order to achieve maximum noise elimination.
-
Product
6x 3U OpenVPX MOSA Data Concentrator Unit
SIU36-DCUVARM-01
Data Concentrator Unit
SIU36-DCUVARM-01 is a Modular Open Systems Approach (MOSA) DO-178C & DO-254 Certifiable Data Concentrator Unit (DCU) with low power high performance OpenVPX Xilinx UltraScale+ SBC with Quad Core ARM Cortex -A53, 8 GB DDR4 SDRAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet, USB 3.0, FIPS-140-3 Level 3 Cyber Security, and Single Event Upset support.
-
Product
19” Rackmount Data Collection System
DCS-211
Data Acquisition System
- Intel Atom® x5-E3930 processor- Up to 8x DI and 6x DO with two 2A relays- 3x M12 GbE, 1x RJ-45 GbE, 2x isolated RS232/422/485, 2x USB and one lockable HDMI port- Up to 3x PCI Express mini slots with one USIM card slot each- Storage: up to 64GB eMMC 5.0, 1x 2.5” SATA drive bay
-
Product
Data Acquisition System - 3U 5-Slot
DAQ-35CP0G
Data Acquisition Module
is a preconfigured rugged system ideally suited to support a multitude of military/aerospace data acquisition applications that require "SBC-less" remote Gig-E command and control of high-density, multichannel programmable ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939); A/D Conversion; RTD Measurement; RS-232/422/485 Serial Communications; Thermocouple Measurement; Discrete I/O; Differential Transceiver and Dual-Port Gig-E Ethernet.
-
Product
Voice Coils
-
CAES can tailor a motor for your specific application. This customization can include size variations and winding characteristics to accommodate power supply availability, performance parameters and physical mounting requirements.
-
Product
Tactical Video Data Link
-
Tactical Video Data Link (TVDL) is a video and data receiver/transmitter system specially designed for attack helicopters. This compact and lightweight system, weighing less than 4 kg, enables real-time, high-quality video imagery and data captured by UAV payloads or ground-based sensors to be displayed directly to the aircrew. This saves the need for lengthy radio dialogue by creating a common visual language amongst all forces in the battlespace and dramatically shortening the sensor-to-shooter loop. As a true video relay, the system can simultaneously transmit video and data as well as deliver imagery captured by onboard payloads to tactical forces for enhanced coordination and battle management.
-
Product
Advanced Voice Quality Assurance System
AVQA
-
R&S®AVQA is a non-intrusive voice assurance system that provides many integrated monitoring functions for ATC communications systems. These functions include:Quality assurance reports to CAAType acceptance of new IP systemsLive information about disturbance to ACC adminVoice quality report on ANSP interconnection (e.g. NewPENS)Network quality reporting
-
Product
16-Ch Isolated Digital Input And 16-Ch Relay USB 3.0 I/O Module
USB-5862
Data Acquisition Module
USB 3.0 SuperSpeedDaisy chainable by built in USB hub16-ch Isolated Digital Input and 16-ch Form A-type Relay OutputWide input voltage range (10 ~ 30 VDC)High-voltage isolation on input channel (2,500 VDC )Quick removable European type connectorLED indicators for I/O statusSupported operating systems: Windows 10/11
-
Product
Video Windows
Cobra
-
Curtiss-Wright Defense Solutions
Cobra is a high-performance, multi-input, video windows processor that can accept up to 12 videos per card and select up to 4 for display as windows on a high-resolution, digital flat panel or analog display. Video inputs can be TV, RS170, RS343, STANAG or hi-resolution computer video up to 1600 x 1200, with considerable flexibility in the formats and video timings.
-
Product
VIDEO SNIFFER
IPVS-1
-
The IP VIDEO SNIFFER is a hand-held meter used to check new installations and trouble shoot existing IP video installations. It instantly displays the communication status of both transmit and receive data lines and also indicates the status of Power Over Ethernet (P.O.E.) lines.
-
Product
16-CH 12-Bit 110 kS/s Multi-Function DAQ Card
PCI-9112
Data Acquisition Module
- Supports a 3.3 V or 5 V PCI bus- 12-bit A/D and sampling rate up to 110kS/s- 16-CH single-ended or 8-CH differential inputs- On-board A/D FIFO
