-
Product
Flame Ionization Detector
-
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
Product
Flame Testing
-
Helping you ensure acceptable flammability and flame resistance for electronic products and components.
-
Product
Flame Burning Tester
DRK3024A
-
Shandong Drick Instruments Co., Ltd.
It is used to detect high temperature resistance, combustibility and combustion performance of materials.
-
Product
Flame Detector
SMC 3100
-
The SMC 3100 Series Flame Detector utilizes a tri-spectra design (UV, IR and visible light spectrums) to provide continuous and reliable flame detection. The 3100 Series design provides the ability to detect flames from both hydrocarbon and non-hydrocarbon sources, making it ideal for a facility where the flame source could be generated from a variety of gases.
-
Product
Integral Explosive-proof Intelligent Flame Detector
FSE-100
-
FSE-100 Explosion-proof Flame Detector is used to collect the flame signal which is amplified and processed to determine the presence or absence of flame. FS-100 Flame Detector provides the flame output in real-time – the basis of determining the presence or absence of flame.
-
Product
Gas & Flame Detection System
Syntel
-
Teledyne Gas & Flame Detection
Syntel is an addressable loop system suitable for use in zone 1 and 2 hazardous areas. The complete addressable loo is fault tolerant operating normally with a short or open circuit. Syntel does not have a CPU, so there is no common failure point. It includes a standard OPC interface and can also be supplied by Modbus allowing easy integration with third party systems.Syntel stores alarm and calibration information in distributed non-volatile memory, hence there is no reliance on a centralized system.Syntel is ideal for installations where there is the possibility for future expansion. The system architecture allows very low cost expansion as cable runs to a central location are not needed.
-
Product
Multi-spectrum IR Flame Detector
FL4000H
-
The FL4000H is an advanced multi-spectrum infrared (MSIR) flame detector that provides superior false alarm immunity with the widest field of view.
-
-
Product
ZY-3 Needle Flame Test
ZY-3/ZY-3S
-
According to IEC60695-2-2 and IEC60695-11-5, ZY-3/ZY-3S Needle Flame Test is applied in the production and quality control department of lighting instrument, hyperpiesia electrical apparatus, domestic appliance, machine electric appliance, electrical machine, power tool, electronic instrument, electrician instrument and technical equipment. Also, it is fit for the industry of insulation material, engineering plastics and solid combustible material.
-
Product
UV/IR Flame Detector for Hydrogen Apps
-
The FL500-H2 is an Ultraviolet / Infrared flame detector designed specifically to detect hydrogen (H2) fires. The FL500-H2 optical flame detector monitors for radiation emitted by a hydrogen flame in both the ultraviolet (UV) and infrared (IR) spectral ranges.
-
Product
Flame Spectrometer
-
The Flame spectrometer is built using industry-leading manufacturing techniques that help deliver high thermal stability and low unit to unit variation without compromising the flexibility and configurability that are the hallmark of Ocean Optics miniature spectrometers. New features such as interchangeable slits, indicator LEDs and simple device connectors deliver more freedom and less frustration.
-
Product
HVFAA Horizontal Vertical FAA Flame Chamber
-
Atlas Material Testing Solutions
The Atlas HVFAA Horizontal Vertical Flame Chamber provides the most accurate means for determining the flammability of aircraft cabin and cargo compartment materials, liners and waste stowage compartment materials, and electric wire. The large volume chamber prevents oxygen depletion during tests. Three digital timers with remote control make specimen event timing precise and convenient. To ensure accurate and repeatable tests, an optional burner flame temperature verification kit is available. The HVFAA is the optimal instrument for conducting repeatable FAA flammability tests and is used in the FAA’s training facility.
-
Product
UV/IR Flame Detector
FL500
-
The FL500 UV/IR Flame Detector monitors for radiation emitted by a flame in both the ultraviolet (UV) and infrared (IR) spectral ranges. This UV/IR combination provides a fast response time and increased false alarm immunity against sources of radiation for reliable protection.
-
Product
Multi-spectrum Infrared Flame Detector
975MR
-
The Rosemount 975MR multi-spectrum infrared flame detector is based on accurately analyzing the multi-spectral signals by utilizing three separate IR sensors. The 975MR detects fuel and gas fires at long distances. For example, this product will detect a 1 ft2 (0.1m2) gasoline pan fire at 215 ft (65 m) in less than 5 seconds. The 975MR also provides the highest immunity to false alarms and enhanced overall coverage range.
-
-
Product
HVUL2 Horizontal Vertical Flame Chamber
-
Atlas Material Testing Solutions
The Atlas HVUL2 Horizontal Vertical Flame Chamber is designed for the flammability testing of plastic materials used in consumer electric devices and appliances per UL94. The chamber is constructed of stainless steel with a black interior and large sliding window for easy viewing. The HVUL2 includes a fully adjustable specimen support and a precision metered gas burner. Three digital timers with remote control are mounted on the inside back wall of the chamber, allowing for precise and simplified line-of-sight operation.
-
Product
SK Elektronik FID Analyzers
-
The Thermo-FID is an MCERTS approved extractive gas analyzer for the measurement of Total Organic Hydrocarbons (TOC) with a Flame Ionisation Detector (FID). Available in a number of different models, each version of the Thermo-FID employs the same detector unit, internal tubing and electronics. Distribution of sample and test gases is provided by using an innovative vacuum system which can be driven using plant compressed air or diaphragm pump.
-
Product
High-Temperature Strain Gages
ZWH-, ZWN-, & ZWP-Series
-
ZWH-, ZWN-, and ZWP-Series strain gages are designed for dynamic and limited static strain measurement at hightemperature.These strain gages are manufactured using a round wire for superior bonding ability and performance. A high-fatigue wire (Option Z) is also available on each of the gages. These gages are supplied with a fiberglassreinforced tape carrier which holds the grid and leads in place during installation and are bonded using ceramic cements or Rokide® flame spray. The shelf-life of thesegages is 9 months.
-
Product
400/5A CHEAP SPLIT CORE CAST RESIN CURRENT TRANSFORMER
LZCK310-10
-
Beijing GFUVE Electronics Co.,Ltd.
LZCK series outdoor waterproof current transformers are applicable for AC power system 35kV and measurement of current of power supply equipment below 10KV also can be used for microcomputer protection. This type of current transformer employs imported silicon steel which with high permeability as magnetic material, has the characteristics of Small magnetic circuit loss and can be split, its semicircular core and secondary windings employ high quality epoxy resin vacuum, casting in plastic-case(ABS or PC) which is flame retardance anti-moisture, stable performance, no maintenance.
-
Product
Flash Point Testers
-
Flash point is the lowest liquid temperature at which a test flame causes sample vapors to ignite. Fire point is the temperature at which the test flame causes the sample to ignite and remain burning for ≥5 seconds.
-
Product
Communications Module
CC02A
-
The CC02A Communications Card facilitates serial communications between each module in a Zero Two Series Flame and Gas Detection System and an external host computer, which allows fast access to operational and setup data registers. It supports a Burst Read feature that returns all registers of a module in a single transmission.
-
Product
Thermal Protective Performance Tester (TPP)
-
Sataton Instruments Technology CO., Ltd
Thermal protective performance tester (TPP) is to determine the heat transmission of protective clothing or textiles exposed to flame and radiant heat resources. The tester which can provide thermal protection index (TPI) calculated by software is the recommended tool for evaluation the potential of second degree burn of the materials to block convective and radiant heat penetration. Analysis software can display real-time temperature curve and automatically detect heat time curve to show Stoll curve for rating the thermal protective performance of tested textiles.
-
Product
Flame Photometers
-
Flame Photometer applies the emission spectrum as the basic principle, which uses the flame heat and excites part of the atoms in alkaline earth metal. The atoms receive energy and transfer it to the old energy level. When the atom is at a normal energy level it releases the energy.
-
Product
Fixed Flame Detectors
-
Teledyne Gas & Flame Detection
Would you like to source high-performance flame detectors? Teledyne Gas and Flame Detection offers detection solutions that precisely meet the needs of the most demanding professionals.
-
Product
Single Channel Detectors
-
Infrared detectors for gas analysis, flame detection and radiometry in TO18 or TO39 packages.Housing types TO18 and TO39Voltage or current modeSignal processing with JFET or operational amplifierThermally compensated (optional)With special chip holder for reducing the microphonic sensitivity (optional)
-
Product
Horizontal Flammability Tester
UI-TX40
-
Horizontal Flammability Tester – Horizontal Flammability Chamber is used to test textile and material used in vehicles horizontal burning rate when exposure to a small flame. Horizontal Flammability Test Method includes ISO 3795, ASTM D5132, JIS D1201, SAE J369, FZ/T01028, GB/T8410, GB/T20953 and etc.
-
Product
Footwear Testing Machines
-
Dongguan Amade Instruments Technology Co., Ltd
Footwear testing machines are designed to determine a variety of mechanical and chemical performances of different types of shoe materials and finished shoes including sneakers, high-heeled shoes, leather shoes, casual shoes, etc. There are appearance performance tests including yellow resistance test, ageing resistance test, fastness resistance test, etc, physical performance tests containing flexing resistance test, rubbing resistance test, anti-slip test, etc, biological and chemical performance tests covering PH test, Formaldehyde content test, flame retardant test, etc, and service life test. Applicable to standards of ISO20344, SATRA, ASTM, etc.
-
Product
Tunable Detectors
-
Due to their spectral properties and robustness, pyroelectric detectors have proven themselves for many years in numerous applications in gas analysis, flame detection and spectroscopy. They enable the tuning of the optical filter over a defined spectral range by simply adjusting the control voltage. Instead of mounting filters to inspect specific areas of interest as is conventionally common, the detector with tunable Fabry-Pérot filters (FPF) can be used to monitor a broad spectral region continuously.
-
Product
GFID Analyzer
-
Gasmet Flame Ionization Detector (GFID) is designed for continuous total hydrocarbon (THC) measurements. GFID analyzer offers a TÜV certified solution (QAL1) for measuring pollutants from hot, wet and corrosive gas streams.
-
Product
Hazardous Area Gas Detector
Meridian
-
Teledyne Gas & Flame Detection
Whether you need an infrared or catalytic bead sensor to detect combustible gases or an electrochemical sensor for a toxic environment, the Meridian universal gas detector utilizes a single detector head to easily accept all sensor types. There is no requirement for distinct personality boards in the gas detector or different detector heads to make the instrument behave as a combustible or toxic gas detector. The Meridian gas detector accepts all sensor types in one detector. Simply attach the specific toxic or combustible sensor to the universal detector head and the Meridian gas detector will automatically determine the type of gas to be detected. Installation of the sensor is a simple plug-and-play action. At Teledyne Gas and Flame Detection, we are always looking to anticipate your future needs. We designed the Meridian gas detection platform to be future proof, allowing you to take advantage of new sensing technologies from Teledyne Gas and Flame Detection while maintaining ease of use and peace of mind.
