-
Product
VME64x Form Factor Extender, 6U x 60mm
116FFE6006-012X
-
The VME64x form factor extender 6U 60 mm allows to adapt boards for use in the same VMEbus system. It maintain the correct depth dimensions and allow the front panel to be aligned.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786167-01
FlexRio Digitizer
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
13-Slot 64-bit 6U Compact PCI Backplanes
cBP-6413DR
Backplane
- 2 Systems- cPCI Bus: up to 64-bit/66MHz- System A: 1 system + 7 Peripherals- System B: 1 system + 4 Peripherals- 1 CMM slot
-
Product
4, 8, 16, 32 Channel ARINC429 Test And Simulation Module For PCI
APXX429-x
Simulator
ARINC429 Test and Simulation bus interface with 4, 8, 16 or 32 Software programmable Tx/Rx channels plus up to 8 Discrete I/O’s.
-
Product
PCI Bus Synchro - Resolver - LVDT I/O Cards
PCI Synchro
-
Computer Conversions Corporation
Proven "Whole" Std. ConvertersOptimized Thermal ManagementExternal Synchro AMP I/O100% Transformer Isolated I/OPermits 2 wire X/Y Stators(Air)No External Parts or Power RequiredReference Powered(NAVAL) Options10-16 BIT Resolution ProgrammableVirtually Indestructible Outputs1.2 to 4.5VA High Power ModelsMix/Match Input & Output TypesSimultaneous Fine/Coarse Transmit For Multispeed Outputs
-
Product
VME Test Extender 3U/220mm J1
111EXT3122-11XX
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 8 Channel
50-201-008
Fault Insertion Unit
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
Product
32-bit PCI Test Backplane
SKU-014-01
-
The 32-bit PCI Test Backplane was designed to support production testing/debugging of PCI-based peripheral boards. The backplane expands the x1 PCI Express interface of the host computer into four 32-bit PCI slots via 7 ft CAT6 cable. The PCI backplane is a versatile platform that allows you to test up to 4 PCI boards at the same time, facilitates easy access to logic signals, provides hot-swap compatibility, and per-slot overcurrent protection.
-
Product
4-port/8-port USB 3.0 PCI Express Card With 4 Independent Host Controllers
AX92321
-
*Four or eight USB 3.0 ports*Four independent USB 3.0 host controllers*900 mA/1500 mA max. per port configurable via jumper settings*Compliant with USB 3.0 Rev.1.0 and Intel® xHCI Rev.1.0*PCI Express x4 interface*Operating temperature from 0˚C to 70°C*Supports Windows® 7/10*Supports each port’s power on/off via software settings
-
Product
PCI Express 16 Isolated Input Digital Interface (10-30V)
8006He
-
Optimized for sensing up to 24V inputs, the 8006He PCI Express digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, pushbuttons, and other user inputs. The inputs can sense both AC and DC voltage while providing optical isolation, which eliminates spikes and surges present in industrial environments. The board is PCI Express X1 compliant and is compatible with any PCI Express slot.
-
Product
16-CH 16-Bit 250 kS/s Low-Cost Multi-Function DAQ PCI Express Cards
DAQe-2213/2214
Data Acquisition Module
ADLINK DAQe-2213/2214 can sample up to 16 AI channels with different gain settings and scan sequences. It makes them ideal for dealing with analog signals with various input ranges and sampling speeds. These devices also offer differential mode for 8 AI channels in order to achieve maximum noise elimination.
-
Product
Single Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-101
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
12-Bit PCI Express ADC/Digitizer
SIS1350-2
-
The SIS1350-2 is the follow up unit to the SIS1350 digitizer card. It was developed for high repetition rate acquisition of short analog signals (i.e. up to 128 µs at 500 MSPS) with good resolution.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 63.7 Ohm
50-294-011
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Precision Resistor Card 9-Channel, 1.5Ω To 925Ω
50-297-021
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Very High Density Multiplexer, 5-Channel, 16-Pole
50-670C-021-5/16
Multiplexer Module
The 50-670C-021-5/16 is a 5-channel, 16-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
PCI High Density Potentiometer Card 4-Channel, 16-Bit, 0 To 65k Ohm
50-296A-121-4/16
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Precision Resistor Card 3-Channel, 3Ω To 11.4MΩ
50-297-153
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
High Temperature, Low Strain, Extended Performance Capacitive Extensometers
Model 7650A
-
Jinan Testing Equipment IE Corporation
Model 7650A extensometers measure strains with extremely high precision due to their design features and low strain range. All models are capable of tension and compression strain measurement, and may be used for fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650A models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to provide high accuracy, high resolution measurements and perform high temperature fatigue testing at the highest possible frequencies. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods for specimen contact when testing to 1200℃ (2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.The Model 7650A is often customized for specific test needs. Contact Epsilon for a configuration that matches your requirement.
-
Product
PCI 96 Channel TTL Digital Interface
8009
-
The 8009 digital I/O interface provides 96 channels of buffered drive digital I/O emulating 8255 mode zero, which can be utilized for PC based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems. 10K pull-up resistors are included. Optional values are available.
-
Product
PCI Express Card
EXC-8000PCIe/xx
-
The EXC-8000PCIe/xx card for the PCI Express bus supports up to forty ARINC-429 channels in any combination of transmit and/or receive. All of the channels feature error injection and detection.
-
Product
1 Channel VGA Over Fiber Transmitter and Receiver Extender
L-1VGA-FE
-
The QuestTel L-1VGA-FE Fiber Optic Transmitter and Receiver provides long haul transmission of high resolution VGA and Audio control signals over a single fiber up to 20km.
-
Product
PMC-to-4X PCI Express (PCI-e/PCIe) Adapter
6777
-
The Technobox, Inc. P/N 6777 is a PCI Express (PCIe/PCI-e) carrier that permits the insertion of a single PMC into a PCI-e slot (4X). The adapter orients the PMC in a reverse manner such that the rear I/O from PN4 appears at the 68-pin SCSI-style connector installed on the adapter’s bracket. Furthermore, the reverse orientation of the card permits direct access to the standard front I/O (if any) within the host chassis.
-
Product
PCI Precision Resistor Card 3-Channel, 2.5Ω To 102kΩ
50-297-140
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Uncommitted Extender
UEC220-3U
-
VECTOR Electronics and Technology, Inc.
Uncommitted Extenders are strictly point-to-point with eachrow of pins isolated on separate layers
-
Product
PCI High Density Potentiometer Card 4-Channel, 12-Bit, 0 To 4k Ohm
50-296A-121-4/12
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Conduction Cooled VPX Interface Board with PCI Express Host Interface
EXC-8000ccVPX
-
The EXC-8000ccVPX is part of the 8000 family of multiprotocol carrier boards. This conduction cooled VPX interface board has a PCI Express host interface and can support up to four independent removable modules and 10 on-board Discrete channels. Each removable module can be any of the 8000 family modules.The EXC-8000ccVPX supports Direct Memory Access (DMA), which enables the board to access system memory for reading and writing independently of the computer’s CPU. This results in faster data transfer to and from the board, with much less CPU overhead than when not using DMA.The EXC-8000ccVPX is supplied with C drivers, including source code. Mating connector provided for I/O connection.
-
Product
PCI 3-Channel Precision Resistor Card
50-297-103
Precision Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
12-Port PCI Express
PEX 8648
-
The ExpressLane™ PEX 8648 device offers 48 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 12 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The 48-lane switch enables users to add scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including servers, communications, storage, blade servers, and embedded systems.
-
Product
PCI Express to VME interface
SIS1100e/3104
-
Single width 6U VME master/system controllerred ball, 1/2/4 GBit/s optical link, red ball, up to 450 m link distance, red ball 128 MBytes memory (PPC Ethernet or VME slave)
