Product

Cable Identification System

KSG 200 / KSG 200 T

-

BAUR

KSG 200 / KSG 200 T - BAUR

Cable identification withBAUR KSG 200. The KSG 200 cable identification system is used to identify single- and multi-core cables in a cable bundle or cable loom. By using the KSG 200, the risk of accidentally cutting a live phase is significantly reduced.* Cable identification on all types of de-energised cables* Reliable verification of the cable identification by means of the highly precise three-factor-analysis ATP* Safe cable identification on live low-voltage cables* Connection technology according to CAT IV/600 V

Product

Cable Identification System

-

Scope T&M Pvt, Ltd.

Scope T&M Pvt, Ltd.

After excavation, sometimes it is confusing to identify the right cable from a bunch of cables. Cable Identification is very important for the safety of field personnel – Cutting a wrong cable can be fatal. So, we require a Cable Identification System to identify the wanted cable.

Product

Low Frequency Generator

LFG-2500

-

Kharkovenergopribor Ltd.

LFG-2500 - Kharkovenergopribor Ltd.

• tracing – finding the route and burial depth of the underground utilities;• fault location – pinpointing phase-to-sheath and interphase short-circuit faults;• cable identification – identifying a correct cable in a bunch.

Product

Cable and Pipe Locator

PT-14

-

Kharkovenergopribor Ltd.

PT-14 - Kharkovenergopribor Ltd.

The locator PT-14 is used as an induction signal receiver in a cable tracing and fault location set for the following applications:• tracing – finding the route and determining the burial depth of underground cables and other hidden utilities;• fault location – pinpointing interphase and phase-to-sheath short circuits faults;• cable identification – identifying a correct cable from a bunch.

Product

Cable Identification System & Cable Phasing System

Impulse Phaser

-

Timco Instruments, LLC

Impulse Phaser - Timco Instruments, LLC

With the introduction of direct buried, solid dielectric primary voltage cables, the IMPULSE PHASER has come into greater prominence for safely and accurately identifying buried primary cables, including jacketed neutral designs. The IMPULSE PHASER has been accurately used on paper insulated, lead covered feeders in excess of 20 miles and even on submarine cable 300 feet underwater.

Product

Cable Identifier

-

K&S Engineering and Scientific Ltd

K&S Engineering and Scientific Ltd

K&S Engineering and Scientific LTD's Cable Identifier Set offers the user a compact, portable solution for cable identification. Depending on the user preference, the Cable Function Generator and Cable Identifier Unit can be jointly housed in a rugged briefcase, or alternatively, for the user requiring a more rugged unit, can be delivered as two individual units each with their own carry-case. With the Cable Identifier Set, power optimum levels are selected by means of a rotary switch and the power levels are displayed on a meter located on the Cable Function Generator. As the Cable Identifier Unit is capable of detecting magnetic fields around mains cables it has the added advantage of the user being able to use this as a stand-alone unit to detect power cable configuration.

Product

Network, Port ID And Cable Tester

One for All PH-400

-

Pansco, Ltd

One for All PH-400 - Pansco, Ltd

The One For All is an all-in-one network tester, tone generator, cable tester, and port ID finder. It comes with a remote unit, allowing pin-by-pin tests of installed cables in addition to patch cables. The office ID feature allows the user to check the ID number of up to 100 networks or patch panel outlets without labeling the cables manually, and the tone generator traces cable using a tone detectable by any market tone probe. The network tester blinks the network hub or NIC port light for the cable being tested, allowing easy cable and outlet identification; and it identifies network speed (10 Mbps vs. 10/100 Mbps vs. 10/100/1000 Mbps) and activity. Line tester included for detect live circuits and preventing damage to the tester.

Product

Cable Identification & Phasing

VCi-3™

-

ndb Technologies Inc.

VCi-3™ - ndb Technologies Inc.

The VCi-3™ system is designed for cable and phase identification, mainly for instal­lation or maintenance purposes on three-phase electrical networks during power shutdowns.The transmitter module injects a low current on the cable conductors by direct con­tact or magnetic clamps methods. A voice message is recorded by the user and will be transmitted along with digital signals. Groundings stay connected at both ends of the three-phase circuit during the test. The detector module is used at the other end of the cable system.

Product

Cable Fault Locators

-

Fiberinthebox

Fiberinthebox

Cable Fault Locator is a device used for short circuit faults, cable cuts, resistive faults, intermittent faults, and sheath faults. Fiberinthebox supply cable fault locator for power cable, optical fiberal cable, etc. Fault Location in Power Cable is designed to locate cable faults, pinpointing the fault location, route tracing, cable identification, voltage withstand test and cable information management. It can locate all kinds of cable faults for all voltage level cables, including open circuit, short circuit, low insulation, high insulation and flashover faults, etc. Most power cables were buried underground, invisible, and out of reach, with modern new power cable fault locater, it can find the fault point quickly, solve problems immediately and restore power supply.

Product

Energized Cable Identification System

LCI™

-

ndb Technologies Inc.

LCI™ - ndb Technologies Inc.

The LCI™ system is intended for energized cable identification on secondary and primary circuits. This innovative solution features a dual frequency technique that eliminates false identifications. The LCI™ is designed to be easy to use, safe for the user and cost-effective.

Product

LAN Cable Multifunction Tester

TCT-2690PRO

-

Tenma

TCT-2690PRO - Tenma

LAN/length cable tester quickly and accurately tests network, telecommunication, cable and security systems for a variety of issues. Tests for open or short circuits, jumpers, cross or split pairs, continuity and wiring of cable patterns, cable identification and length measurement using included remote ID.

Product

Low Frequency Generator

LFG-50

-

Kharkovenergopribor Ltd.

LFG-50 - Kharkovenergopribor Ltd.

• tracing – finding the route and determining the burial depth of underground cables and other hidden utilities;• fault location – pinpointing interphase and phase-to-sheath short circuits faults;• cable identification – identifying a correct cable from a bunch.

Product

Coaxial Cable Tester

6106

-

Peaceful Thriving Enterprise Co Ltd

6106 - Peaceful Thriving Enterprise Co Ltd

This device is designed to test the connection of F type coaxial cable. The testing includes continuity and cable mapping. The tester includes 4 mapping terminals with different color and a F type adapter, which are very helpful for cable identification.