Video Distribution Amplifiers
See Also: Distribution Amplifiers
-
Product
Broadband Power Amplifier
PAS-08025-30
-
* Solid State Power Amplifier* Gain : 50 dB typ.* High IP3, 48.0 dBm typ.* Rack Mount Case* Internal Cooling Fans* Over Temperature Protection* Output VSWR protection* Microprocessor controlled* Front Panel Information Display* RS-232 Interface* Ethernet Interface* Variable Gain* ALC power control* Type N Connectors
-
Product
Low Noise Amplifiers
WA Series
-
WA series low noise amplifiers are the balance type LNA with alarm capability in some of the products. Besides offering very low noise figure and wide bandwidth, the LNA have high linearity with unconditional stable design. The noise figures are from 0.40 dB to 1.0 dB and IP3 from 30 dBm to 40 dBm.The amplifiers cover the frequency bands of VHF, UHF, Cellular, GSM, DCS, PCS, 3G, C, and wireless LAN. The built-in alarm capabilities include Branch 1 and Branch 2 alarms, Soft Failure alarm, Hard Failure alarm, Soft alarm Open-Collector, and Hard alarm Open-Collector.
-
Product
LXI Dual 24 X 8 Video Matrix, SMB (50R)
60-711-721
Matrix Switch Module
The 60-711 is a Dual 24x8 Video Matrix Module suitable for switching frequencies up to 25MHz. It has a characteristic impedance of 75 Ohm with the option of SMB or MCX connectors or, with a larger case size, BNC connectors. It is designed to provide a simple and scalable bidirectional matrix for video frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems. Software configuration allows the 60-711 to be set as a dual 24 by 8 matrix, a single 48 by 8 matrix and other configurations.
-
Product
1U, Rack Mount, Pulse Distribution amplifier
A5000P
-
The Quartzlock A5000P is a 1U, rack mount, pulse distribution amplifier
-
Product
Video Decoding
-
MediaKind’s Video Decoding products combine to cover the full requirements for any installation, of any size.
-
Product
Amplifiers
-
Use our optical amplifiers to improve the signal-to-noise ratio (OSNR) and range performance of optical transmission systems.
-
Product
Sierra Video
-
Professional AV switching and terminal equipment for post-production, broadcasting, and digital or analog applications.
-
Product
High Voltage Amplifier
WMA-100A
-
The WMA-100A model is our cost-effective, compact, general purpose high voltage amplifier. With its high quality and small form factor, it is the ideal choice for any experiment that requires an all-round, reliable high voltage amplifier. It can also be used as a stand-alone low noise high voltage power supply. Two WMA-100A amplifiers and a WMA-IB-HS phase inverter - buffer can be used to double the output voltage.
-
Product
Single Phase Lock-In Amplifier
SR510
-
Stanford Research Systems, Inc.
The SR510 and SR530 are analog lock-in amplifiers which can measure AC signals as small as nanovolts in the presence of much larger noise levels. Both the single phase SR510 and the dual phase SR530 have low-noise voltage and current inputs, high dynamic reserve, two stages of time constants, and an internal oscillator.
-
Product
Voice and Video over LTE and 5G
-
Enable scalable high-definition voice and video over LTE and 5G with industry-leading Radisys Engage Media Server.
-
Product
Lock-In Amplifiers
-
Anfatec's lockin amplifiers use a unique DSP technology which is only found in these instruments. High speed real-time data processing is combined with optimized analogue input stages. Fully digitally designed high quality filtering ensures an excellent suppression of background signals and an unsurpassed dynamic reserve.
-
Product
Frequency & Pulse Distribution
-
Timetech frequency distribution amplifiers and pulse distribution units.
-
Product
Bi-Directional Amplifier
-
RF Lambda’s bi-directional amplifiers can be used in repeater type applications where a single conductor is used for both receive and transmit. These amplifiers offer low noise figure and high linearity. Hermetically sealed options are available upon request.
-
Product
VHF Band 1.0 Watt Amplifier With RF Bypass
-
Teledyne RF & Microwave has developed a 35 to 350 MHz custom amplifier with 1 watt output power. The amplifier has 29 dB gain with 3 dB noise figure. The amplifier assembly has a RF switch so that the RF input can be connected directly to the output bypassing the amplifier. The amplifier goes into the "bypass" state when the DC bias is removed from the switch. This unit is one of a series of amplifiers that covers the 1 MHz to 2100 MHz with similar operation.
-
Product
Graphics and Video
-
Leading edge commercial technology (NVIDIA, AMD/CoreAVI) coupled with Abaco’s ruggedization expertise delivers blazing high performance graphics and video performance from a range of platforms and small, lightweight mission-ready, pre-integrated subsystems.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Unipolar High Voltage Linear Amplifier
P150
-
The P150 is a general purpose linear amplifier having a fixed amplification of 20 times and capable of unipolar high voltage output of +150V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to +10 V can be used as an input device. The amplification can be set to x15 (or other value) on request.
-
Product
Small Signal RF/Microwave Power Amplifier
-
R&K’s small signal amplifier series are to amplify various high frequency signals such as CW/Pulsed/AM/FM/N-DCMA/W-CDMA/OFDM , etc.
-
Product
CATV Amplifiers
-
Electronic devices that boost weak TV and broadband signals (audio, video, data) traveling through coaxial cables, compensating for signal loss from splitters, long cable runs, or network nodes to maintain strong, clear picture/data quality for multiple devices, operating across specific frequency bands for both forward (downstream) and reverse (upstream) paths.
-
Product
Rail-to-Rail Op Amplifiers
-
Analog Devices high speed (> 50 MHz) rail-to-rail op amps enable you to operate at lower supply voltages, swing closer to the rails, and provide wider dynamic range. Featuring a portfolio with a wide variety of op amps, including both rail-to-rail input/output as well as just rail-to-rail output, ADI provides the widest portfolio of leading edge products available on the market. Whether it is wide bandwidth, high slew rate or low distortion, or rail to rail, no one sets more performance standards for next generation designs than Analog Devices.
-
Product
2.5G Distributed Feedback Lasers
-
Macom Technology Solutions Holdings Inc.
MACOM’s Distributed Feedback (DFB) laser diodes are designed for direct modulation uncooled operation up to 2.5Gb/s. These products utilize patented Etched Facet Technology (EFT) for exceptional reliability with the following benefits: *Etched Facet Technology enabling high performance and product uniformity*Wide operating temperature range for wireless, PON and datacenter applications*No isolator required due to high back-reflection rejection
-
Product
Low Noise Amplifiers
-
Electronic component that amplifies a very low-power signal without significantly degrading its signal-to-noise ratio (SNR).
-
Product
Amplifiers
-
Elbit Systems of America’s secure networks and communication solutions provide warfighters secured and reliable radio communications for most operational applications. Our teams work hard to deliver a number of scalable options from extremely rugged to standard industrial or commercial specifications. Our family of Single-Channel and Dual-Channel Modular Power Amplifiers operates with current and next-gen radios and offer lightweight, compact solutions on most platforms. The modular design simplifies maintenance, provides customer flexibility, and accelerates the fielding of new capabilities.
-
Product
RF Amplifiers up to 2500 MHz
-
L and S Band 1,2,4, and 8 Kilowatt rack mount solid state microwave amplifiers ideal for CW and pulse TWT amplifier replacement utilizing GaN technology and rivals the TWT amplifier in size and weight. Also available is our broad line of high power modules including 25, 50, and 100 watt pallets for integrating into your own power amplifier design.
-
Product
Intelligent Panel Mount Meter Amplifier/ Conditioner
MODEL DPM-2
-
The voltage-to-frequency microprocessor makes Transducer Technique's 4-digit panel mount meters the ideal solution for meeting the measurement, display and control requirements of noisy industrial applications, OEMs and system designers. Model DPM-2 accepts any full bridge transducer. Balance and span can be selected via the front keypad, thus allowing the display to read directly in engineering units. Front panel max and tare functions are ideal for industrial weighing applications. Isolated adjustable 9-11 VDC excitation with remote sense and 90 mA drive eliminates the need for external power supplies. Rear screw terminals connectors are included.
-
Product
LVDT Sensor Amplifiers
-
Analog Devices signal conditioning ICs, together with linear variable differential transformers (LVDTs), can be used to convert mechanical position to a dc voltage. The IC provides both the excitation for the LVDT and the output conversion to dc level with a user selectable gain. ADI LVDT signal conditioners are available to interface with a wide range of LVDTs, including half bridge and standard 4- and 5-wire.
-
Product
Erbium Doped Amplifier
AEDFA-FTTH
-
Amonics FTTH EDFAs inherit the reliable design of Amonics's optical amplifier technology. They exhibit high output power, high gain with very low noise, and are ideal for FTTH network amplification. Integrated CWDM splitters are available to enable routing of 1310nm and 1490nm data streams from OLT to ONU through EDFAs. The turnkey rackmount EDFAs provide microprocessor controlled alarms and status indicators. An integrated Ethernet TCP-IP computer interface enables easy control, diagnostic functions and data acquisition.
-
Product
Analog to Digital Video Converter/Embedder
SDI Pro VADC-100
-
The SDI Pro VADC-100 converts composite analog video to SDI video and embeds two channels of analog audio.
-
Product
LXI Single 24x8 Video Matrix, SMB (50R)
60-711-711
Matrix Switch Module
The 60-711 is a Dual 24x8 Video Matrix Module suitable for switching frequencies up to 25MHz. It has a characteristic impedance of 75Ω with the option of SMB or MCX connectors or, with a larger case size, BNC connectors.
-
Product
C & L-Band Separate Raman Fiber Amplifier
RFA7000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
