Simulation Testing
See Also: Simulation, Simulators, Simulation Software
-
Product
PXI Battery Simulator Module, 4-Channel, 5 Amp
41-754-011
Battery Simulator
The 41-754-011 and 43-754-011 are 4 channel battery simulators, capable of supplying up to 8 V and 5 A per channel. The channels are fully isolated from ground and from each other allowing series connection to simulate batteries in a stacked architecture. The isolation barrier (1000 V channel to GND and 750 V channel to channel) allows the module to be used as a battery stack representative of those used for vehicle propulsion..
-
Product
GPS Simulator
ADIVIC MP6220
Simulator
Multi-channel GPS simulator for GPS receiver position fix testIndividual channel is power adjustableSingle channel mode for receiver S/N ratio testTunable power output level from -160dBm to -55dBm
-
Product
Desktop PCB Test System
BOARDWALKER 9627
Test System
Qmax Test Technologies Pvt. Ltd.
QT9627 is a cost effective entry level model Desktop PCB Test System. It can be configured to maximum 64 Channels of In-circuit Functional Test Channels and 64 Channels of QSM V-I Signature Test .Maximum Digital Test Speed 10MHz in the QT9627 .
-
Product
Solar Array Simulator DC Module, 130V, 5A, 600W
E4362A
Simulator
The Keysight E4362A is a 600W solar array simulator DC power module that simulates the output characteristics of a solar array. The E4362A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin etc.). The E4360 gives you the flexibility to operate it in two ways:
-
Product
In-Line RF Test Platform
AR925
Test Platform
This functional and RF test platform combines outstanding productivity with substantial equipment savings. The Faraday chamber of the fixture comes with an interchangeable cassette to minimize the testing cost of each new product
-
Product
Hybrid Single Site Test Handler
3110
Test Handler
Chroma Hybrid Single Site Test Handler 3110 is a full range ATC (Active Thermal Control) test handler capable of handling device bodies up to 120x120mm with 450kg force load.
-
Product
Electronic Control Unit Functional Test
Functional Test
End-of-line tests are critical to ensure passenger safety in the era of smarter vehicles. A flexible test solution is needed to ensure extensive test coverage and high test throughput with a low total cost of ownership.
-
Product
Scalable Tester System for Functional Testing
UTP6010
Functional Test
The UTP6010 is a scalable tester system for functional testing, comprising an integrated main switching unit, a keyboard drawer and a swivelling monitor. It is the reliable, modular, low priced UTP starter kit. The system is suitable for tester applications, where space-saving devices are required, because its construction height is only 12 HU (excluding keyboard drawer and main switching unit).
-
Product
Automated Test Systems
Test System
WinSoft designs, develops and integrates automated functional test systems for use in aerospace, military, high tech and commercial applications
-
Product
H(3)TRB & HTGB Test Systems
Test System
SET offers two H(3)TRB and HTGB product lines which differ in the number of test object channels and the range of technical possibilities. The innovative systems are scalable, modular and standardized.
-
Product
Other Test Systems
Test System
Your business challenges do not fit the typical mold. Your test requirements are different. Ball Systems has more than 50 years of experience in multiple industries that has exposed our team to a wide variety of testing applications. As a result, we’ve likely created a solution for a challenge similar to yours.
-
Product
Test Port Cable, 1 Mm
11500J
Test Port Cable
The Keysight 11500J test port connector has a length of 16 cm and a frequency range of DC to 110 GHz. The 11500J integrates with the Keysight N5250A network analyzer and Keysight 8510XF network analyzer systems.
-
Product
Test Fixture, Axial And Radial
16047A
Test Fixture
The 16047A is designed for impedance evaluation of axial/radial lead type devices of up to 13MHz. The 16047A employs Kelvin contacts which realize a wide impedance measurement range. The contact tip can be changed according to the device shape.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, 1 kV Isolation
41-752A-113
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Dual Port Simulator Fiber Channel PXIe Module
PXIe-FC4 Simulyzer
Simulator
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. By simply upgrading the firmware / software, a single function board can become a full function board without having to purchase new hardware.
-
Product
Imperial Test Executive
ITE
test
The Imperial Test Executive (iTE) is a UI shell that sits on top of National Instruments TestStand. It provides a simple but elegant interface to execute your NI TestStand sequences. The iTE software was designed to allow general operators to execute ATE testing software without requiring any knowledge of NI TestStand. Training an operator to use this system typically takes less then 5-minutes.
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 24 Channel
41-761-002
Simulator
The 41-761-002 is a low voltage 24-channel output module ideal for simulating theoperation of a thermocouple, also available with 32, 16 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
-
Product
Test System
BMS HIL
Test System
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
Product
Eagle Test Systems
ETS-200T
Test System
The ETS-364 is a general-purpose precision analog and mixed-signal test platform designed for high volume production testing of integrated circuits; optimized for high throughput applications with a fully integrated multisite software and hardware architecture.
-
Product
EOL RF Functional Test
AS652
Test Platform
With this RF test platform, integrable according to the specific needs of the product, we cover a very wide range of test needs with manual feeding.Ergonomics have been fully observed in the design, including the option of servo adjustment of the working height according to the operator.
-
Product
Radio Frequency, Communications, & Navigation Test Systems
Test System
Reduce testing time and costs with the Astronics radio test sets for use in military, avionics, and civil security industries.Available in commercial and military grades, these integrated test systems make it easy to develop test program sets and leverage them securely and instantly across all deployed testers at the factory, depot, and operational levels.
-
Product
Semiconductor Test System
TS-960e
Test System
The GENASYS Semi TS-960e PXI Express Semiconductor Test System is an integrated test platform that offers comparable system features and capabilities found in proprietary ATE systems. Available as a bench top system or with an integrated manipulator, the TS-960e takes full advantage of the PXI architecture to achieve a cost-effective and full-featured test solution for device, SoC and SiP test applications.
-
Product
NI Automated Test Software Suite
test
The NI Automated Test Software Suite features all three NI IDEs and NI's most popular application software and add-ons specifically for building your automated test system with confidence. This package offers the power of LabVIEW, LabWindows/CVI, and Measurement Studio combined with the TestStand ready-to-run, test executive and the Switch Executive intelligent switch management application
-
Product
RSE Wireless EMC Spurious Emission
TS8996
Test System
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
Product
Test Handler
M4841
Test Handler
High-Throughput Device Handler for Volume Production Testing of MCUs and DSPs.
-
Product
NI Real-Time Test Cell Reference System
780590-35
test
VeriStand Full Development License with NI Standard Service , Include 1 Year SSP
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel With V/I Readback
41-752A-012
Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Memory Test System
T5511
Test System
Offering Multi-functionality and Industry's Top Test Speed of 8Gbps.
-
Product
PXI RTD Simulator Module, 8 Channel, PT100
40-263-401
Simulator
The 40-263-401 is an 8-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 32 Channel
41-761-001
Simulator
The 41-761-001 is a low voltage 32-channel output module ideal for simulating theoperation of a thermocouple, also available with 24, 16 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
