Leeb Hardness Testers
See Also: Hardness Testers, Brinell Hardness Testers, Rockwell Hardness Testers, Vickers Hardness Testers
-
Product
Concrete Hardness Tester
W-M-250
-
The W-M-250 Manual Test Hammer is the traditional instrument used for the non-destructive testing of hardened concrete. This easy-to-use instrument provides a quick and simple test for obtaining an immediate indication of concrete strength in various parts of a structure. The minimum verifiable strength is 1400 PSI (10 MPa)
-
Product
sonic tester
PR-82
-
The PR-82 sonic tester has been modified for the automotive industry. This gauge is commonly used for measuring the thickness of cylinder walls, head ports, decks, tubing, body panals, and windshields. It also has the ability to scan the length of a part to find the the minimum thickness.The PR-82 is back-lit and the unit operates for up to 200 hours on a single set of batteries. It is protected by Dakota Ultrasonics 5 year limited warranty.
-
Product
ProxiLAB Quest Contactless Tester
-
Fully programmable card (PICC), reader (PCD) and NFC signal emulator for device characterization and protocol conformance verification. ProxiLAB Quest offers the performance and features required for full characterization and conformance validation of all 13.56 MHz contactless technologies, including the latest very high bit-rate evolutions. ProxiLAB Quest integrates with a variety of conformance certification solutions and test automation platforms.
-
Product
Ultrasonic Testers
-
Our Ultrasonic Thickness Gauge range, is the widest selection on the market with the best cost/performance ratio. On some of the models the warranties are extended up to 5 years while all of these gauges are efficiently and fully backed up and supported. These models are normally carried in stock for fast delivery.
-
Product
Melt Flow Testers
-
nstron®'s CEAST Melt Flow Testers are specifically designed for easy and accurate measuring of the Melt Flow Rate (MFR) and the Melt Volume Rate (MVR). CEAST Melt Flow Testers range from systems that perform a simple manual test procedure to semi-automated testing systems performing multiple weight tests. Our testers meet ASTM and ISO standards.
-
Product
Digital LOOP/PSC Tester
8025 LP
-
Standard Electric Works Co., Ltd
● Battery is not used.● 3 ½ digit LCD (2000-count).● Backlight function.● 15mA loop measurement which will not trip ELCBs.● Convenient and easier for users to measure the loop impedance directly without bypassing the wires.● Wiring check function.● Over temperature protection.● Over voltage protection.● Built-in voltmeter.● Built-in earth tester.● Built-in loop/psc tester.● Safety standard : EN 61010-1 CAT III 300V EN 61326-1
-
Product
Battery Leak Testers
-
Battery leak testers are crucial tools in the quality assurance process for battery manufacturing. These testers are designed to detect any leaks in battery cells, ensuring that the batteries are safe and reliable for use. Battery leaks can lead to reduced efficiency, potential damage to devices, or safety hazards. By employing sophisticated techniques, such as pressure decay methods or helium detection, battery leak testers can identify even the smallest imperfections in battery casings. These testers are essential in industries where battery reliability is critical, such as in automotive, consumer electronics, and renewable energy sectors, ensuring that the batteries meet stringent safety and quality standards.
-
Product
Multifunction Earth Tester
MT-100
-
Multifunction earth tester for measuring earth resistance, continuity of protective conductors’, with touch-screen display and integrated Wi-Fi
-
Product
Harmonics and Flicker Testers
-
complied standards and features of the KHA1000 (dedicated for single phase), is equipped for the harmonic and flicker compliance test exceeding 16A of the single-phase and three-phase equipment. With this unit alone, you can take highly accurate simultaneous three-phase measurements up to 40A/phase*.
-
Product
Electromagnetic Field Tester
-
The EMF tester is designed to provide user a quick, reliable and easy way tomeasure electromagnetic field radiation levels around power lines, home appliancesand industrial devices.
-
Product
Conventional friction and wear tester
EFM-III
-
The measurement unit of A&D's conventional friction and wear tester has been adjusted to enable the measurement of friction characteristics with higher precision.
-
Product
Electromagnetic Force Micro Tester
Micro-Servo
-
This is a multi-functional fatigue testing machine suitable for specimens, structures and full-sized parts. It is an overhead actuator type with a broad test space, so it is ideal for various types of environmental tests, such as those in corrosion tanks or constant temperature tanks.
-
-
Product
Insulation & Multifunction Tester (LCD Display)
1154 TMF
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
Product
Gas Permebility Testers
-
Guangzhou Biaoji Packaging Equipment Co., Ltd.
Gas Permebility Testers used to test the gas (o2,N2,C o2, ect) transmission rate of packing materials, such as plastic film, composite film, aluminum-plated film, and so on.
-
Product
Digital Durometer Digital O-Ring Hardness Kit
OHK-DD-4
-
The Digital Complete O-Ring Hardness Kit is the most convenient and accurate way to perform repeatable hardness (durometer) testing on thin materials - as thin as .050". Conforms to ASTM D-2240
-
Product
Relay / Magnetic Field Testers
-
PeakTech Prüf- und Messtechnik GmbH
Ideally suited for checking magnetic fields and the correct function of coils, e.g. Relays and solenoid valves. The magnetic field detector works without contact, so that opening the housing is not necessary in most cases. When a magnetic field is detected, the probe tip lights up permanently blue, with clocked relays in the same cycle as they are controlled. The function of the magnetic field detector can be checked before each measurement with the enclosed test permanent magnet.
-
Product
AC Programmable Hipot Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
AC Programmable Hipot Tester
-
Product
Hardness Testers
-
* Compact plastic case, suitable for use under poor working conditions. Test at any angle, even upside down.* Wide measuring range. It can measure the hardness of all metallic materials. Direct display of hardness scales HRB, HRC, HV, HB, HS, HL* Large screen (segment LCD), showing all functions and parameters. With EL background light.* Large capacity memory could store 100 groups information.* Datapro Software to connect with PC via RS232 port. Micro printer support* Software calibration function.
-
Product
Discharge Tester
-
It is a new impulse winding tester that incorporates high precision, a wide range of functions, various expandability, improved operability, and a full range of external communication interfaces.
-
Product
Cable Testers
CableJoG 64
-
CableJoG 64 can test up to 64 individual connections of all manufacturers of connectors. This simple test instrument stores up to 55 separate connection configurations. Each cable that is tested is compared with the configuration stored in the cable testers memory to produce a pass/fail indication of each pin connection.
-
Product
Reciprocating friction and wear tester.
-
This testing machine is used to evaluate surface conditions such as friction faces of materials by measuring the frictional force.
-
Product
LOADpro Load Testers
-
LoadPro is an external Web load testing service. A LoadPro test simulates actual user traffic from outside your network, stressing your entire infrastructure in order to discover bottlenecks that impact performance under peak traffic.
-
Product
Servo Tester
105
-
Simulates a receiver so you can test your motors and servos without having to use a transmitter and receiver. It can send RC-PWM signal of 1ms to 2 ms in 20ms period. It connects to an ESC via three wires. The servo tester is powered by the BEC in your speed control or by a std 4 cell 5 volt receiver battery
-
Product
Insulation Testers
-
Kyoritsu Electrical Instruments Works, Ltd.
The insulation resistance (IR) test (also commonly known as a Megger) is a spot insulation test which uses an applied DC voltage (typically either 250Vdc, 500Vdc or 1,000Vdc for low voltage equipment <600V and 2,500Vdc and 5,000Vdc for high voltage equipment) to measure insulation resistance in either k, M or G.
-
Product
6-12V Heavy Duty Circuit Tester
1651
-
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems. Use on accessories including lights, starters, alternators, cooling and heating components, radios and relays.
-
Product
Gear Teeth Hardness Tester
PHT-1840
-
This dedicated unit is designed to test gear teeth and other difficult to access applications. The 1840 is loaded with the same features found on the base 1800 version which includes memory, USB output and software for downloading to your PC. The 1840 hardness tester is capable of measuring the surface hardness of a broad variety of metals on flat and round surfaces. This instrument comes complete with a dedicated DL impact device, calibrated test block and rugged carry case.
-
Product
Tester, US Mains Socket
72-6861
-
The 72-6861 is a Receptacle Tester with 3-indicator light. 2nd-Amber indication for ground contact (Open ground) and 3rd-amber indication for neutral contact (Open neutral) not connected, for hot and ground contacts interchanged indication by red and amber. If 2-amber indication occurred, receptacle is wired correctly.
-
Product
Coil-on-Plug Spark Tester
TH458
-
For ignition systems with coil-on plugs, including Ford, Chrysler, Chrysler imports, Mitsubishi, Nissan, and more. Since coil-on plug ignitions do not have plug wires, inductive test equipment cannot be used. Spark tester tests for no-start conditions and measures coil output.
-
Product
MIMO Tester
-
Qosmotec Software Solutions GmbH
The QPER MIMO Tester is a handover tester einriched with phase shifter that helps engineers to make mobile networks fit for modern standards like LTE or HSPA+.
