Exposure
-
Product
Outdoor Exposure Tester
OET
-
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
Product
Exposure Systems
Model 2012AF & 2012SM
-
The Model 2012AF Flood Exposure System provides a cost-effective method for automated flood exposure. Designed to accommodate wafers from 8” to 300mm, the tool features automated FOUP loading. Mask and substrate changeover can be accomplished quickly and easily adding to both versatility and high-volume throughput of this production tool.The Model 2012SM Automated Edge-bead Exposure System provides a cost-effective method for edge-bead removal using standard shadow mask technology. Designed to accommodate wafers from 8” to 300mm, the tool features automated FOUP loading. Mask and substrate changeover can be accomplished quickly and easily adding to both versatility and high-volume throughput of this production tool.
-
Product
UV Exposure Sources
-
Standard maintenance, lamp, or filter replacement, does not require any tools. Locking indicator dials on all the system controls, located together for ease of alignment, provide for a reproducible setup. A beam imaging accessory makes alignment even faster.
-
Product
External Fire Exposure Test Machine, Battery Safety Testing
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL external fire exposure test machine is applicable to the standard UL 2580.
-
Product
Exposure Level Tester
ELT-400
-
*Wide frequency range (1 Hz - 400 kHz)*Standard-compliant measurement*Acceptance measurements compliant with CE standard IEC/EN 62233 and Generic Standard IEC 62311*Limit value traces conforming to ICNIRP 1998, 2010 and EMF Directive 2013/35/EU*Real time measurement with RMS and peak detectors*External FFT signal analysis for determining the frequency components via three channel analog output (one channel for each spatial axis) e.g. with the aid of a digital oscilloscope.
-
Product
Vehicle Electromagnetic Field Exposure Test System
SEM-400
-
Beijing KeHuan Century EMC Technology Co,.LTD
Vehicles are our daily public transportation. Electromagnetic pollution in vehicles has attracted more and more public attention. The newly revised compulsory standard GB27630-201X "Passenger Car Air Quality Evaluation Standard" intends to require the electromagnetic field in the car as one of the indicators, according to GB/T37130-2018 "Measurement method of vehicle electromagnetic field relative to human exposure" The measurement method is to measure the intensity of the magnetic field in the car. In the frequency range of 10Hz-400kHz, the electromagnetic field measurement result should meet the public limit requirements of GB8702-2014 for electromagnetic exposure.
-
Product
Microwave Leakage Tester
TEK500
-
An easy to use, low cost pass / fail microwave leakage detector suitable for commercial and domestic microwave ovens. It is designed to comply with national standards on permitted exposure levels. The TEK500 includes a self test which simulates a real microwave input to ensure the unit is working correctly at all times.
-
Product
13MP MIPI Camera Module
e-CAM130_CUMI1820_MOD
-
e-CAM130_CUMI1820_MOD is a 13MP MIPI Camera Module. This small form factor 13MP camera module comes with S-Mount lens holder. It is based on AR1820HS – an 18MP CMOS Image sensor from Aptina™ / ON Semiconductor® and has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs all the Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images and video and the optional MJPEG compression. Though the AR1820HS is an 18MP image sensor, the e-CAM130_CUMI1820_MOD supports only up to 13MP resolution.
-
Product
Light and Energy Meter
Model 659
-
UV Light and Energy Meter for use with all wafer steppers. For over 45 years, OAI is a world leader in UV Light and Energy Measurement Instrumentation used for reliable accurate calibrated control of the photolithography processes in the Semiconductor, MEMS, Wafer Packaging and Wafer Bumping Industries. The New Model 659 is an advanced UV exposure analyzer specifically designed for use with all wafer steppers including high intensity wafer steppers. This meter averages up to 400 exposure readings, has Ethernet and USB interface for downloading recorded measurements, and has intensity range of up to 7,500mW/cm2. Probes are available in wavelength of 365nm, 400nm, 420nm & 436nm. OAI has a complete certified calibration lab to maintain the performance, quality and reliability of our meters. The Model 659 meter is traceable to NIST standards.
-
Product
EYE Super UV Tester
-
UV rays are the greatest cause of product deterioration. This unique system dramatically intensifies the deterioration acceleration caused by UV rays. It can achieve an acceleration factor greater than 100 times normal sunlight, producing material effects equivalent to extended outdoor exposure. Its compact size makes it ideal for research and development testing of paints, inks, pigments and fibers as well as plastics.
-
Product
Preconditioning
-
Preconditioning is performed prior to package level reliability testing to simulate the effects of board assembly on non-hermetic devices where moisture may have been absorbed during normal storage. The subsequent exposure to high temperature during infra reflow assembly can cause internal damage such as “pop corning” and delamination.
-
Product
Tabletop Front & Backside Mask Aligner
Model 200IR
-
The OAI Model 200IR Mask Aligner is a tabletop system that requires minimal clean room space. It is a cost-effective alternative for R&D or limited scale, pilot production. Utilizing an innovative, air bearing / vacuum chuck leveling system, the substrate is leveled quickly and gently, for parallel photo mask alignment and uniform contact across the wafer during contact exposure. The Model 200IR Mask Aligner is capable of one micron resolution and alignment precision. It has an alignment module which features mask insert sets and quick-change wafer chucks that enable the use of a variety of substrates and masks without requiring tools for reconfiguration. The alignment module incorporates micrometers for X, Y, and z-axis.
-
Product
Large Substrate Mask Aligner
Model 6020
-
The Model 6020 is a large substrate Production Mask Aligner or Auto-flood Exposure System for RDL First Level Advanced Packaging (PLP) and markets requiring exposure of large glass panels. It is engineered with OAI’s precision, reliability, and quality that is found in all of OAI’s products. The features include wedge effect leveling, superb process repeatability, ≤ 2.0µm printing resolution, and remote diagnostics. Using robotic handling, the system can stand alone or be fully integrated with photo resist processing.
-
Product
Calibrate Camera RAW Image Files
SpyderCUBE™
-
Accelerate RAW processing by taking one reference shot under any light condition to set the white balance, exposure, black level and brightness right from the start for your entire series of photos.
-
Product
SAR Testing
-
RF transmitters used in close proximity to the human body must be evaluated against human Exposure standards which set basic restrictions for the Specific Absorption Rate (SAR) of RF energy by any part of the human body. This may include two-way radios, cellular phones, smartphones, spread spectrum, Bluetooth devices, wireless EFTPOS terminals and WLAN devices used in PDA/notebook/laptop/tablet computers. In Australia and Europe, virtually all devices exceeding the power threshold of 20mW (13dBm) and used in close proximity to the human body must comply with SAR requirements. There is no such blanket exemption in the USA and Canada where each product must be assessed against frequency/power level criteria.
-
Product
Human Vibration Management Software
HVManager
-
HVManager is a Risk Assessment and Recordkeeping software tool for reporting Vibration measurements and predicting Personal Exposure Levels. It provides reports of vibration measurement data from hand-arm and whole-body measurements acquired from the Larson Davis HVM100 Human Vibration Meter and produces vibration database records by tool type and serial number. HVManager also compiles cumulative predicted vibration exposure levels from any combination of tools and task durations taken from the measurement database.
-
Product
Computer Controlled Photoreactors
CCP
-
Luzchem has developed the latest in exposure chamber technology. Our new computer controlled photoreactors (CCP-4V and CCP-ICH2) are fully computerized using a USB interface. These photoreactors will automatically log exposure conditions and optics used. New integrated power sensor will also log the intensity of the light output. Ideal for pharmaceutical testing and any other industry with stringent documentation requirements.
-
Product
RF Safety Monitoring
MVG EME Guard XS Radar
-
Specifically designed to alert workers operating near radar transmitters of RF exposures, the unique EME Guard XS Radar is an RF pulse measuring device. It continuously scans for short pulsed signals, and via its built-in alarm and visual system, alerts users whenever the acceptable limits have been exceeded. This RF Safety tool is extremely easy to use and creates a safer working environment close to radar antennas and other pulsed RF sources.
-
Product
Stability Test Chamber
-
Wewon Environmental Chambers Co, Ltd.
Test Instrument to simulate effects of weathering conditions, e.g. UV light exposure and water exposure, on samples to conveniently predict the relative durability of a sample, e.g. paint, surface coatings, plastic and related materials.
-
Product
Cryogenic Temperature Sensors
Thermocouple wire
-
Thermocouple wire is used in a variety of cryogenic applications, but special techniques must be employed to approach temperature accuracies of 1% of temperature, even without consideration for the effects of high magnetic fields or high radiation fluxes. The problems are further complicated by exposure to variable gradient conditions at cryogenic temperatures.
-
Product
Conductive Emission Measurement
-
Holland Shielding Systems B.V.
On site testing for exposure limits in working conditions to any international standard. This involve pacemakers and HSE Heath and safety executive, invitarisations worldwide.
-
Product
Relative Humidity Logger Sensor
NUL-207
-
This sensor measures relative humidity. It can find use in recording variations with weather conditions and the relative humidity effect on organisms such as seedlings and insects. It is located in a plastic box with exposure of the sensor being through a hole in the side.
-
Product
Scientific Imaging
-
The TRiCAM is a compact intensified camera for scientific and industrial applications that require low-light level imaging or ultra-short exposures through fast gating.
-
Product
Sweep Frequency Response Analyzer
FRANEO 800
-
FRANEO 800 was developed for testing the mechanical and electrical integrity of power transformers after transportation or exposure to high fault currents. It uses the sweep frequency response analysis (SFRA) principle and measures the electrical transfer function over a wide range of frequencies.
-
Product
13MP 4K Camera Module
e-CAM131_CUMI1335_MOD
-
e-CAM131_CUMI1335_MOD is a high performance, 13 MP 4K camera module with S-Mount lens holder and it has better low light performance. This small form factor 4K camera module is based on 1/3.2” AR1335 CMOS image sensor from ON Semiconductor® and has a dedicated, high-performance Image Signal Processor (ISP) that performs the entire Auto functions like auto white balance, auto exposure control in addition to complete image signal processing pipeline that provides best-in-class images and video and the optional MJPEG compression.
-
Product
Noise Dosemeter
Castle GA257B
-
The SONUS Pocket Dosemeters are designed to be powerful and easy to use. These dosemeters are small and tough so measurements and data can be collected throughout the working period. Data can be reviewed on screen or downloaded to a PC for further analysis. The SONUS GA257B is a dedicated basic dosemeter fully compliant with IEC 61252:1993 and IEC 61672-1:2013, giving simultaneous sound exposure (Lep'd) and maximum peak (Zpeak) measurements, an essential feature for Noise at Work Regulations assessments.
-
Product
Control Unit for SITEx & SITExs
SITEX SCU286
-
The SCU286 has a system for direct measurement of the high voltage delivered by the X-Ray generator to guarantee the accuracy of the radiological parameters. Based on this data the control system maintains the stability of mA and kilovolts to within ± 0.5% in any selection range.SITEX & XS units offer a totally constant quality of exposures, as they are virtually exempt from fluctuations in the power supply.
-
Product
Profiling Belt Radiometer
ILT400
-
International Light Technologies
The IL400 Profiling Belt Radiometer continues with the all-in-one exposure, intensity, and profiling capability first introduced in the IL393. New solid-state detector and ultra-stable amplifier technology along with rechargability combine to give lower noise, greater speed, and higher accuracy at a price below any precision belt radiometer sold today.
-
Product
Magnetometers
-
The strength of magnetic fields can be determined with a magnetometer. Regardless of whether in the private sector or in the work environment, the increasing use of technology and networking also increases the exposure to magnetic and electromagnetic radiation. This radiation can have a negative effect on living beings, but also on sensitive electronic devices. Many effects are so unspecific that radiation is often not recognized as the cause. With a magnetometer you can measure how strong the radiation is at your sleeping place, in the kitchen in front of the microwave or induction stove or at your workplace. The location of sensitive electronic devices such as a precision balance can be examined with the magnetometer. The extent to which the radiation intensity increases or decreases with distance can be determined by positioning the magnetometer at various distances from the radiation source.
-
Product
Solar Panel Testing Chamber
ZPH Series
-
CSZ's solar panel testing chambers aid in qualifying that modules can withstand the thermal stress caused by repeated changes in high and low temperatures along with exposure to high humidity. Unique air flow design and distribution ensures precise air flow required for solar panel testing.
