Pulse Amplifiers
increase amplitude while keeping waveform. Also known as: Pulsed Amplifiers
-
Product
Dynamic Power Device Analyzer/Double Pulse Tester
PD1500A
Power Device Analyzer
As an off-the-shelf measurement solution, the PD1500A delivers reliable, repeatable measurements of wide-bandgap semiconductors. The platform ensures user safety and protection of the system’s measurement hardware.
-
Product
HF Amplifier
Prometheus
-
The design of the Prometheus is the result of over 10,000 hours of research and development, encompassing hundreds of hours of mathematical analysis, computer simulation and modeling, and numerous prototypes and experiments spanning over a five year period. The result is a rugged, commercial quality amplifier designed to run cool under 1500W continuous SSB, CW or RTTY, with special ferrite transformers and combiners designed for full power operation even on 160 meters. Although our custom transformers are more expensive and difficult to manufacture than competing designs, they do not saturate or heat up beyond the Curie point, thereby becoming irreversibly damaged and destroying the RF transistors in the process.
-
Product
Dual Channel High Voltage Linear Amplifier
F20AD
-
This unit contains two independent F20A amplifiers that share common ground reference and power supply.
-
Product
Power Amplifier, RF
-
Is a type of electronic amplifier that converts a low-power radio-frequency signal into a higher power signal. Typically, RF power amplifers drive the antenna of a transmitter.
-
Product
10MHz Pulse Generator With Delay
TGP110
-
0.1Hz to 10MHz frequency rangeIndependent control of pulse frequency, width and delay50ns minimum pulse widthSquare wave, double pulse & delayed pulse modesFree-run, gated and triggered modes50 Ohm output: 0.1V to 10V amplitudeTTL/CMOS and Sync outputs
-
Product
High Voltage Amplifier
HA-805
-
*800Vp-p(±400V DC) *200mAp-p(±100mA DC) *Bandwidth: ≦300KHz(400Vp-p) *Slew Rate: 300V/us *Gain(AMPL):0~180(10 Turn VR) *DC Offset: ≦0~±400V(10 Turn VR+SW) *Output Resistor: 100Ω *Microprocess Control Protection
-
Product
Pulse & Delay Generators
-
The benchtop pulse generators feature a fast risetime and low jitter. Our most popular digital delay pulse series 575 and 577 generators are now available with selectable time references. With up to eight channels of delay and width control, each individual channel's reference can be set either to the trigger or to any other channel. So look below if you require a picosecond pulse generator or nanosecond pulse generator for your application.
-
Product
Low Noise Amplifiers
-
LNA amplifier PE15A1000 is rated at 13 Volts DC maximum and 200 mA. Our low noise radio frequency LNA amp is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. This coaxial millimeter wave low noise amplifier can ship worldwide the same day of the purchase as with our other available RF parts.
-
Product
Fiber Optic Amplifier
-
Shanghai Pubang Sensor Co.,Ltd.
1. High response frequency, detect with super high speed2. Suitable for detecting small objects3. Non-contact, non-destructive detection,can be used in harsh conditions4. Simple mounting by DIN connection
-
Product
Saluki SE1201 DSP Lock-In Amplifier
-
SE1201 Small-sized Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 50 mHz to 120 kHz. With the high-speed 4-core architecture, high-precision ADC and excellent analog performance, SE1201 can easily detect the phase and the magnitude of weak signals overwhelmed by various large noise. The performance of SE1201 is as good as other lock-in amplifiers brands, even better in some certain parameters, such as measurement accuracy, operating bandwidth, which meets the needs of scientific research and industrial application well.
-
Product
Pulse
-
*MODBUS Master RS485 / RS232*Up to 10 slaves or 15 registers per slave*Monitoring and supply of power to the sensor*Local and remote configuration
-
Product
Shortwave Plus 50 MHz Power Amplifier
OM2000A+
-
Thank you for purchasing this new model of the OM Power’s RF power amplifiers line for HF and 50 MHz amateur radio bands. You now own, the OM2000A+, an automatic unit with no knobs, no rotaryswitches on the front panel, just two small switches and one large touch display.Smart design, modern conception, high reliability is the result of OM Power’s development and many years of experience with overall solutions and special attention with the design of the protection circuits.This product is covered by two years of warranty on the amplifier itself and one year for the tube.We wish you will have many years of trouble-free use of this equipment, lots of fun and successful contacts in the world of amateur radio.
-
Product
Pulse Generator
Digital Ring Kits
-
NEMA C frame rings provide mounting for 1101, 1201, and 1202 shaft speed sensors for use with 199SM magnet wheels on motors with NEMA C frames. The DRK (Digital Ring Kit) Series provides a single-channel output and the QDRK (Quadrature Digital Ring Kit) Series offers a bi-directional output. Kits include mounting ring, hardware, magnet wheel, and sensor.
-
Product
Very High Speed Pulse Generators (Rise Time ≤ 1 ns)
-
The Avtech high speed pulse generator line includes models with rise times as low as 40 ps! Instruments are available in a variety of formats, including DC-powered externally-triggered modules, simple AC-powered benchtop pulsers with knob and switch controls, as well as more sophisticated instruments with GPIB,
-
Product
Sample/Track and Hold Amplifiers
-
Analog Devices offers a portfolio of sample-and-hold amplifiers and track and hold amplifiers that combine speed with precision. ADI sample-and-hold amplifiers can acquire a signal in 700 ns and hold it with a droop rate of 0.01 µV/µs. These devices are up to 14-bit accurate, with low aperture jitter and output impedance, and they are available in commercial, industrial, and military temperature ranges.
-
Product
Measuring Amplifiers
-
Smart force measurement with a parameterizable measurement amplifier.
-
Product
Flex Power In-Line Non Shut-Off Pulse Tools
-
The non shut-off pulse tools are ideal selection when the operator needs to control the fastening process. These rugged assembly tools increase productivity and enhance product quality through precision torque control and user comfort. The FlexPower Pulse Tools provide operators with an industry leading power-to-weight ratio, allowing for a smaller tool selection for greater torques giving operators a lighter tool with more torque capability. Ergonomically safer than harmful hammering and vibration of impact wrenches. Built for durability with a superior O-ring design and specially designed pulse fluid FlexPower extends life between regular oil changes and provides more torque stability. Offers comfortable rubberized non-slip grips for easy handling and excellent thermal ergonomics. Low noise decibels, minimal vibration and low torque reaction. It is important to understand your joint application before a selecting a pulse tool.
-
Product
Pulsed Withstand Voltage Safety Test
-
Suzhou 3ctest Electronic Co.,Ltd.
Designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment), ITU-T K21 and ITU-T K44.
-
Product
Totalizer (pulse input)
-
Two independent scalable pulse-input channels. Count up or down to a preset at rated up to 1 MHz. Scaled rate and total from the same electronic counter. Scaling for direct readout in engineering units, such as gallons or cubic feet based on counts from a turbine flow meter. One channel can display total while other displays rate.
-
Product
Hybrid Amplifiers
Limiting
-
Macom Technology Solutions Holdings Inc.
MACOM offers a complete line of RF and microwave limiting amplifiers. Our limiting amplifiers use the latest thin film hybrid manufacturing techniques to obtain the highest level of performance, repeatability, and reliability. MACOMs portfolio of amplifiers range from 10 MHz to 4 GHz and are ideally suited for hi-reliability and mission critical applications.
-
Product
50 µs Pulse Medium Current Source/Measure Unit (MCSMU)
B1514A
Source Measure Unit
The 50 s Pulse Medium Current SMU is an SMU designed for faster pulsed IV measurement. It enables a pulsed measurement down to 50 s pulse width, a 10 times or more narrow pulsed measurement than provided by a comparable conventional SMU. In addition, the instrument offers a wider range and versatility, up to 30 V / 1A, with voltage/current programmability. It is useful to characterize high to medium power devices on the new materials such as SiC and GaN, and organic devices, and the MCSMU expands your choices of pulsed IV measurement.
-
Product
100-Amp Current Calibrator And AC/DC Transconductance Amplifier
2555A
-
World’s Leading Precision 100-Amp AC/DC Current Standard - For 30 years Valhalla Scientific’s design has proven rock-solid reliability in metrology labs worldwide. The 2555A is a calibration powerhouse with wide-ranging applications and unsurpassed quality.
-
Product
CATV Booster Optical Amplifier
HA5100
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA5100 series is a CATV booster optical amplifier with gain spectrum band within 1540~1563nm. This kind of optical amplifier is designed for the application of single channel or 1~8 continuous ribbon channels (ITU wavelength). Generally, fiber CATV system operates in single wavelength that has no strict requirement on gain flatness. HA5100 booster amplifier is featured with low NF, high-saturated output power. It is applicable for central bureau, sub-bureau and line relay, as well as other optical communication network. HA5100 is applied most commonly and widely compared with other optical amplifier in CATV system.
-
Product
Panel-mounted Power Amplifier(Hardware In The Loop Simulation)
PA30Bi
-
PA30Bi is the panel-mounted type real time simulation amplifier with three-phase current and four-phase voltage.
-
Product
860MHz CATV Indoor Bi-directional Amplifier
-
Hangzhou Softel Optic Co., Ltd.
SA801H Indoor Bi-directional Amplifier are special amplifiers designed for the last”1km” of the bi-directional transmission network. Special CATV RF modules packaged in SOT-115 are used as forward channel; Microwave tube push-pull circuit with low noise are used as backward channel ;It has the characteristics of low power consumption，high reliability and excellent cost performance. And it is suitable for small and medium sized CATV bi-directional transmission network.
-
Product
OEM Pulse Energy and Power Measuring Instrument
LEM 2510
-
This OEM-Meter is assembled in a standard cassette for the industrial 19? system. It has a width of 21TE. A touch panel and function keys make this device comfortable and easy to handle. The preamplifiers integrated into the device and the choice of sensor sensitivity, allow to use a wide range of sensor heads.?
-
Product
E-Band Low Noise Amplifier MMIC
AWL-7186
-
The AWL-7186 is a 4-stage ultra-low noise amplifier that provides a noise figure of less than 3.5 dB, an output P1dB of +8 dBm, and an adjustable gain range of 15 dB. The MMIC features exceptional gain flatness and superior noise performance over a very wide bandwidth. It is implemented in 0.1 um GaAs PHEMT technology.
-
Product
QuickLink Solder-In Starter Pack for use with Dx20 Amplifier
Dx20-QL-3SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Pulse AC Method Area Ionizers
ER-X Series
-
Panasonic Industrial Devices Sales Company of America
The ER-X Series Area Ionizers utilize the pulse AC ionization design to achieve high-speed charge removal of wide surface areas for high-volume production lines. In addition to supporting compressed air ionization, the ER-X also features both airless and low-pressure ionization modes for applications where tiny workpieces can be easily blown away. Additional features include automatic ion balance and discharge frequency control (manual control is also possible), flat discharge surface for easy cleaning, discharge needle air barrier design to reduce contamination of the needles, replaceable discharge needle unit for easy maintenance, and a dual head configuration for enhanced charge area and layout (2 different ionizer heads can be connected to a single controller).
-
Product
Broadband Power Amplifier
PAS-08025-30
-
* Solid State Power Amplifier* Gain : 50 dB typ.* High IP3, 48.0 dBm typ.* Rack Mount Case* Internal Cooling Fans* Over Temperature Protection* Output VSWR protection* Microprocessor controlled* Front Panel Information Display* RS-232 Interface* Ethernet Interface* Variable Gain* ALC power control* Type N Connectors
