-
product
Integrating Sphere With Holder Base
IS-*MA
1. The hold base can bear max 20kg, it can expanding to test all lamps such as E27/E40, all tubes such as T5/T8/T12, and all kinds of luminaries2. The hold base can be installed in the ceiling or down, it can be adjusted the height3. Hold base has four power cables connect to the outside Power Supply and max is 5KW4. The holder base is detachable. For some kinds of light sources you may need to change the position of the holder base.5. Diameter: IS-0.3M (0.3m), IS-0.5M (0.5m), IS-1.0MA (1.0m), IS-1.5MA (1.5m), IS-1.75MA (1.75m), IS-2.0MA (2.0m). Other sizes can be designed according to the customer’s request.6. The painting of integrating spheres is according to CIE Pub. No.84 (1989)
-
product
Test Solutions For Integrators
Beyond being your test equipment expert, Testek can also provide engineering design advice and guidance on building complete test solution facilities. We will work closely with your building contractor to advise on the most optimal layout configuration and to specify all facility resource requirements. For systems that may share resources, we can facilitate resource demand and management, including power management and fluid management. With a central control system, we can provide software logic to monitor these resources and route them appropriately based on demand and priority.
-
product
YIG Integrated Products
With a 30 year YIG heritage, Teledyne RF & Microwave integrates YIG components with related microwave technologies, creating custom solutions that leverage the advantages of YIGs in cost-effective assemblies including synthesizers, receivers, converters and more.
-
product
Integrating Spheres
Integrating spheres are used especially for measuring divergent light sources such as LEDs. The light is introduced through the input port, then reflected many times by the highly reflective interior of the sphere until it illuminates the inner surface uniformly. A detector samples a small fraction of this light to measure the total power input. Ophir integrating spheres have a highly reflective diffuse white coating for measurements independent of beam size, position and divergence. There are several sphere sizes, apertures and wavelength regions available. The large IS6 series has 2 configurations for measuring divergent or parallel beams.
-
product
Integrating Sphere
The standard test temperature is 25, but high power lamps such as HID lamps and LED outdoor luminaires will produce a lot of heat during the test, thus the temperature inside the integrating sphere can not meet the requirements of IEC standards. Lisun Group designed the Constant Temperatured Integrating Sphere which allows the lamp was tested in a constant air temperature.
-
product
Cormon Integrated Monitoring Software
CIMS
Cormon Integrated Monitoring Software (CIMS) processes real-time corrosion, erosion, pressure, or temperature data from up to 50 monitoring sensors to provide a complete picture of pipeline and device health. Alarm functions can be configured to ensure that potential issues are identified with ample time for correction, reducing operational risk and unplanned downtime. CIMS is the only industry software that can bring together data from both topside and subsea sensors, giving operators a comprehensive view into the entire asset integrity program.
-
product
Integrating Spheres For Reflection, Transmission, Absorption
Universal integrating spheres and accessories optimized for the measurement of reflection, transmission, absorption and photoluminescence
-
product
Integrators
Integrators are used to meassure electric charges in real time. In contrary to digital charge integration, the analog integrator accuracy does not depend on the frequncy of data sampling and can resolve small changes disregarding the data sampling rate. In case of pulsed signals, the analogue integration produces reliable results without requiring high data transfer rates.
-
product
Integrated Multi-Gas Detector for Unmanned Aerial System
MUVE C360
The FLIR MUVE™C360 is a multi-gas detector completely integrated with an unmanned aerial system (UAS) to provide real-time continuous monitoring of chemical hazards while on the move. The sensor block boasts 8-channels, which includes a photoionization detector (PID), Lower Explosive Limit (LEL) detector, and six other sensors. The integrated snorkel is designed to negate the effects of rotor wash, extending past the propellers to sample the unperturbed air. The MUVE C360 sensor block quickly latches to a proprietary integration dock mounted to the UAS. The FLIR calibration station features the same dock, so the operator can easily connect for routine sensor verification. Sensor readouts are prioritized based on alarm conditions and are displayed real-time on the pilot’s interface in the FLIR VueLink™ app. The MUVE C360 is a time-saving, game-changer for emergency responders, industrial safety officers, and environmental monitoring experts.
-
product
Miniature AE Sensor With Isolated Integral 30 DB
The Guzik miniature AE sensor with isolated integral 30 dB preamplifier has a wide-band and excellent frequency response over the range of up-to 1 MHz. Its small size makes the sensor ideal for hard disk drive test or similar applications requiring very small size, low weight, wideband AE sensor response and high sensitivity. A small diameter, external flexible cable connects the sensor with a 3-pin JST connector on the other end.
-
product
Integrated Laser Controller
ILC
AOSense has developed a compact Integrated Laser Controller (ILC) that can be paired with our External Cavity Diode Lasers (ECDLs) to control laser current, piezo transducer (PZT), and temperature. The ultra-low noise electronics are fully digitally controlled. The ILC dimensions are only 5″x2.9″x0.95″. We provide software with an easy-to-use graphical user interface (GUI) that can control multiple lasers from a single window. If preferred, commands may be sent over a USB virtual COM port. The software screenshot below (click the image to enlarge) shows the interface including a plot of the temperature (green line) as it settles to a commanded value.
-
product
Integrating Sphere FT-NIR Spectrometer
QuasIR 3000™
The QuasIR™ 3000 was designed from the ground up to offer the industry a new kind of NIR analysis solution – a solution that brings together the portability required to move NIR analysis closer to point-of-need, combined with unmatched spectroscopic performance for the fastest and most accurate results.
-
product
Charge Integrator Amplifiers
AD8488
Analog Devices’ charge integrator amplifiers convert the charge acquired by X-ray or photodiode detectors to a voltage. The channels are composed of CMOS transistors, using typical high input impedance CMOS gates. The integrators generate charge dependent voltages using a range of selectable capacitance values that accommodate a broad range of input charge values. The integrators are followed by single-ended input to differential output voltage amplifiers where offset and low frequency noise voltages are subtracted from the input voltages.
-
product
Integrating Spheres
Integrating spheres for measurement systems for light and optical radiation, transmission, reflection and absorption. For integrating sphere light sources or based material for customer integration of e.g. PTFE based integrating spheres. We as an experienced manufacturer of integrating spheres can surely implement your application ideally! Either based on standard integrating sphere systems or individually configured integrating sphere setups.
-
product
Integrating Spheres For UV
Konica Minolta Sensing Americas, Inc
Instrument Systems offers complete measurement solutions for UV-A, -B and -C radiation starting from 200 nm. The operation of the well-proven Instrument Systems spectroradiometers, e.g. CAS series, with integrating spheres made from PTFE facilitate high sensitivity measurements of UV radiant flux.
-
product
Integrated Transformer Test Van
XD90
Hangzhou Xihu Electronic Institute
The XD90 integrated modular power system testing vehicle provides an integrated yet flexible solution of preforming a wide selection of normal and specialty tests on power equipment. Designed with the effectiveness and efficiency of power testing in mind, this platform achieves the goal of “integration of functions” instead of just a “combination of instruments”. Not only it provides an abundant means of power testing, but with optimized device placement, operational convenience, and safety factor.
-
product
High-Voltage Test Hood with Integrated Hipot
LX-HVE900IS
Large test room with a hood made of sturdy, highly insulating and transparent plastic, which guarantees a clear view of the test item and the signal lamp during the test. The system is operated on the test device. Alternatively, test sequences stored on an integrated computer can be started automatically by closing the hood. The test sequence can be fully followed on the monitor.
-
product
Systems Integration for Circuit Card Assembly
Teledyne Advanced Electronic Solutions integrates CCAs and other sub-assemblies, cables and fabricated parts into system modules shipped directly to customers for integration into their products.- Box Build: custom built to order system solutions- High complexity box assemblies and subsystems- High frequency RF box assemblies and subsystems- Full functional RF testing up to 26 GHz (K band)- Multi-level systems integration – build and test modules and CCAs and integrate into higher level assemblies- Custom cell design for customer subsystems- Special bonding processes including thermal management and vibration- Robust torque and FOD control programs- System level testing including functional, vibration and thermal- Complex harness fabrication and integration- Fiber-Optic and RF waveguide integration and testing- Large system capacity in excess of 200 lbs.- Configure to order – Integrate different options, firmware, configurations, etc across a single order as required
-
product
Meter w/ pH Electrode, Conductivity/ATC Probe, Integral Electrode Holder
PC 700
The multi-parameter Eutech PC 700 measures pH, ORP, conductivity and temperature with a single meter. User-friendly with advanced features and a large custom-size display – perfect for research work on a budget!
-
product
Microwave Wideband Synthesizer w/ Integrated VCO
ADF5356
The ADF5356 allows implementation of fractional-N or integer-N phase-locked loop (PLL) frequency synthesizers when used with an external loop filter and an external reference frequency. The wideband microwave VCO design permits frequency operation from 6.8 GHz to 13.6 GHz at one radio frequency (RF) output. A series of frequency dividers at another frequency output permits operation from 53.125 MHz to 6800 MHz. The ADF5356 has an integrated VCO with a fundamental output frequency ranging from 3400 MHz to 6800 MHz. In addition, the VCO frequency is connected to divide by 1, 2, 4, 8, 16, 32, or 64 circuits that allow the user to generate RF output frequencies as low as 53.125 MHz. For applications that require isolation, the RF output stage can be muted. The mute function is both pin- and software-controllable.
-
product
Integration API
Testdroid API is an easy-to-use gateway for managing your development and testing effort on real Android and iOS devices. As an alternative for an official Testdroid Cloud site, the API provides all infrastructure through different clients (e.g. Java, Python, Ruby) following the RESTful architecture paradigm and returning JSON with appropriate HTTP response codes.
-
product
Integrating Sphere Spectroradiometer System for LED
LPCE-2(LMS-8000)
LPCE-2(LMS-8000) is an Integrating Sphere Spectroradiometer LED Testing System for identifying the performance of single LEDs and LED lamps. LED’s quality should be tested by checking its photometric, colorimetric and electrical parameters. According to CIE 127-1997 and IES LM 79-08 standards, it recommends using an array spectroradiometer with integrating sphere and photometer head to test SSL products. LISUN GROUP developed LPCE-2 test system for LED products.
-
product
Integrated Development Environment
All Cosmic C Cross Compilers for Windows include IDEA - Cosmic's own integrated development environment which is preconfigured for the the compiler it comes with. IDEA is designed specifically for developing embedded applications with Cosmic compilers. IDEA integrates an editor, project manager, graphical smart build/make facility, program analyzer, link file generator, documentation manager and ZAP debugger into one easy to use environment running under Windows Windows 7, XP and compatible. IDEA includes the following features:
-
product
Integration of Inline Test Systems
The test system and adapter can also be integrated in inline test systems. Additional communication can take place via interfaces (e.g. RS232, DLL). We have already created numerous integrations for different manufacturers.
-
product
Integrated MIC/MMIC Assemblies (IMAs)
PMI offers the highest quality multi-function modules and integrated microwave assemblies for commercial and military applications in the frequency range of a few MHz to 50 GHz. If you do not see exactly what you need, please e-mail your requirement to sales@pmi-rf.com so we can propose an instant solution.
-
product
VLT Integrated Testlane Concept
VLT's intelligent test lane concept was introduced in 1994 and has since then been updated regularly. Intelligent test lanes are mainly used in PTI (Periodic Technical Inpsection) stations. These inspection stations deal with large numbers of vehicles every day and have to keep downtime of the equipment to an absolute minimum.
-
product
MCCI Catena® 4551 Integrated Node for LoRaWAN™ Technology
Based on the Murata CMWX1ZZABZ-078, and designed to be compatible with the Adafruit Feather family of development boards and accessories, the Catena 4551 is a great platform for LoRaWAN investigation and deployment. It works well with The Things Network, or any LoRaWAN 1.0 or 1.1 network in the 865 to 923 MHz range.
-
product
IFE Integrated Power
EmPower® IFE Integrated Seat Power Systems are based on the advanced technology created for the EmPower® AC In-Seat Power Systems with smaller volume and higher efficiency than can be found in non-integrated systems. The Seat Power Box (SPB) is designed to provide both 110V AC power for passenger PEDs and DC power for the IFE, USB charging ports, and other in-seat equipment. The SPB is capable of operating in several modes including AC/DC, AC only, or DC only, and provides dynamic power allocation between AC and DC outputs.
-
product
24-Channel Digital I/O With Digital Integration Features On M.2
M.2-DIO-24A
The M.2-DIO-24A is an M.2 card, and optional cable assembly (D-Sub 37-pin Male connector) designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program. This also allows for simple and trouble-free migration from other ACCES PCI and PCI Express digital I/O cards, but also provides for advanced features enabled by the onboard FPGA logic.
-
product
Probes With Integral Connectors
Used when quick and easy removal and installation are important requirements at the measuring device. Available in quick-connect, terminal block, m8, m12, and other popular connector styles.
