Network Load
-
Product
Acoustic Load Shackle
ALS-2.0
-
The Acoustic Load Shackle is designed for subsea operations where load monitoring is required, either for short term operations lowering an item to the seabed or for longer periods monitoring dynamic loads.
-
Product
Digital Panel Mount Load Cell Meter
MODEL DPM-3
-
The DPM-3 is a smart Plug & Play TEDS IEEE 1451.4 compliant Digital Panel Mount Load Cell meter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the DPM-3 will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the DPM-3 can be set up by simple front panel push buttons. The DPM-3 can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, etc. The DPM-3 samples 60 readings per second (50 for 50Hz operation) for fast control response and true peak/valley reading capability. The meter has an adaptive digital filter that can automatically select the best time constant for minimum noise, yet respond rapidly to an actual change in signal level. The peak and valley values can be displayed by a push of a button on the front panel. Auto-tare allows the meter to be set to zero for any input signal level. Available options include dual relays, analog output, serial communications, and low voltage power supply.
-
Product
Vector Network Analyser
LA19-13-02
-
The LA19-13-02 is a PC-driven Vector Network Analyser suitable for measuring a wide range of devices from 3 MHz to 3 GHz with 100 Hz resolution. Its full s-parameter test set includes bias-Ts for biasing active devices. It is housed in a small lightweight package making it very portable.
-
Product
10GbE Network Attached Storage
HSR10
-
Curtiss-Wright Defense Solutions
The High-Speed Recorder 10 (HSR10) is a network attached storage (NAS) device designed for high-speed network recording based on a double 10 Gigabit Ethernet (GbE) port layout. What’s more, to adhere to security requirements for mission-critical applications, this unit is designed with two-layer encryption and follows industry-standard NAS protocols permitting system design flexibility.
-
Product
48V / 200 Amp Load
BD12-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
Network Interface Card
PMC-GBIT-DT2BP
Interface Card
The Ethernet network interface complies with the IEEE 802.3 specifications for 10BaseT, 100BaseTX, and 1000BaseT over category 5 twisted-pair cable. Full-duplex and half duplex modes are supported. The PMC-GBIT-DT2BP is compliant with standard singlewide PMC IEEE P1386.1, PCI 2.2, and PCI-X 1.0 specifications.
-
Product
Load Tester for A Type dDrometers
-
A load tester for checking the spring load characteristics of ASKER hardness testers at the hardness readings of 25, 50, and 75.It is necessary to check the shape and height of the indentor, the indicating mechanism, and other parts of the hardness tester are set correctly before doing a load test. This tester is applicable to "quasi-object"models with spring load characteristics slightly different from that of object models by adjusting the reference value accordingly.
-
Product
Internal Load Digital ESU Analyzer
ESU-2300
-
Measurements via Industry Standard Current Sensing Method. The ESU-2300 uses advanced ultra-high-speed waveform sampling techniques to accurately analyze even the most complex electrosurgery generator waveforms.
-
-
Product
Electronic Load Mainframe GPIB
3300 Series
-
A 4 Channels 1200W Mainframe which accepts up to four Load Module.
-
Product
Portable Three-Phase Phantom Load
EE-120A-3 + EE-500V-3
-
The Phantom Load is able to generate three-phase voltages and currents with unprecedented stability and measurement accuracy. The amplitude and phase-shift of each current and voltage is individually adjustable. The generated values of voltage, current, power, power factor, phase shift, THD and frequency are indicated on the LCD display.
-
Product
Network Monitoring Tool
-
Motadata’s proactive network performance monitoring tool can be used to automatically discover network devices, interfaces, and applications. The network monitoring software in a multivendor IT environment ensures complete visibility of IT infrastructure. The unified view enables IT admins with a comprehensive picture of the overall IT health and also provides drill-down root-cause analysis, enabling them to resolve network issues even before they affect business processes. It facilitates monitoring of hybrid multi-vendor environment using 100+ pre-defined monitoring templates with immediate notifications on the set threshold values.
-
Product
Streamline Series Vector Network Analyzers
-
With the Keysight Streamline Series, you can expect a common UI, measurement capabilities, and automated code in all form factors: USB, benchtop, and modular. This allows you to move between product development phases more efficiently and effectively since you can transfer knowledge and data easily among the various platforms.
-
Product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD | VP 230036
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.
-
Product
Micro Power or Micro Coax, Insert, Receiver, SIM, 2 Pos, 2 Slot (not loaded)
510180104
SIM Insert
Not loaded. Micro Power or Micro Coax patchcords need to be purchased separately.
-
Product
Mixed-Signal Active Load Pull System
MT1000 And MT2000 Series
-
The MT1000 and MT2000 mixed-signal active load pull systems are the best commercially proven solutions capable of performing load pull at high speeds of up to 1000 impedance/power states per minute with no limitation on Smith Chart coverage, under the following conditions:Single-tone CW and pulsed-CW RF signalDC and pulsed-DC biasTime-domain NVNA voltage and current waveforms and load linesFrequencies between 1 MHz and 40 GH
-
Product
Wireless Networks
-
GrayStone Automation offers our Phalanx family of state-of-the-art, sustainable, energy efficient wireless remote control products for industrial, scientific and general automation applications.Our Phalanx wireless family include products for monitor & control instrumentation, wireless remote controls and off-grid solar power systems.
-
Product
500 AMP Carbon Pile Load Tester
CP710
-
Tests batteries rated as high as 1000 CCA or 160 amp hour. Also tests alternators, regulators, and starters
-
Product
Airborne Network Flight Test Recorder
TTC nREC-7000
-
Curtiss-Wright Defense Solutions
The nREC-7000 is a high speed network recorder for use with Flight Test Data Acquisition and Multiplexing units. The nREC-7000 accepts data for recording on two 10GBASE-SR ports and two 1000BASE-T ports that can store data at sustained speeds of up to 1,000 MBps per 10GbE port. The recorder is also capable of acquiring, formatting (using PCAP, DARv3 or IRIG-106 Chapter 10/11), and recording 10GBASE-SR Ethernet at line rate.
-
Product
Radio Access Network
RAN
-
Break free from traditional restrictions of proprietary networks with Radisys Connect Open RAN protocol software and accelerate 5G deployments.
-
Product
Compact Low Profile Load Cell
1000 Series
-
Compact Low Profile load cells are fully stainless steel, hermetically sealed load cells with a multi-beam internal structure, and fully integrated electronics to provide high level analog or digital outputs. This type of load cell is easy to use for measuring tension or compression loads from 200N (50lb) to 5kN (1000 lb), and is capable of rejecting side forces that would otherwise affect accuracy. This type also offers the user the ability to set the gain and offset (span and zero) electronically, to provide maximum flexibility for the user application.
-
Product
Battery Load Tester
Battery Beak
-
Cross the Road Electronics, LLC
The Battery Beak is a battery load tester that is capable of delivering an 18 amp load and measuring a batteries internal resistance, state of charge (SOC), and can determine the overall health of the battery. The Battery Beak supports all battery chemistries but has additional features to determine battery health for both Lead Acid and NiMH chemistries and supports a variety of AmpHour/Voltage combinations.
-
Product
Load Washer
5000 Series
-
The Load cell is a stainless steel sub-miniature strain gage based transducer with compensated temperature performance. This type provides measurements up to 20000 lbf with better than ±0.5% (full scale) non-linearity
-
Product
VBR Load Analyzer
-
The Powerohm Variable Braking Resistor Analyzer will determine what braking resistor ratings are required for your specific application. The Powerohm VBR is a portable test unit that provides selectable steps of resistance for analyzing your braking requirements for a wide range of drive horsepowers. Simply connect the VBR to your drive or braking module and let the application decide what braking resistor it needs. Once you determine the optimal resistance value for your drives peak performance, the VBR's digital readout will accurately display the true duty cycle as the application runs.
-
Product
AC Load Bank (Resistive/Capacitive)
K-1000 Resistive/Capacitive
-
Kongter Test & Measurement Co., Limited
A RCD (resistive/capacitive) generator load bank is non-linear load bank. The electronic and non-linear loads simulated by capacitive load banks are typical of the Telecommunications, Computer or Uninterruptible Power Supply (UPS) Industries.
-
Product
Networked CCTV
TCP/IP
-
As most of the test sites are using a LAN, we also offer camera systems that are accessed and controlled via TCP/IPIn this case the camera or controller has an Ethernet interface that is connected to the LAN. If our video control SW is installed on a PC, You may access the camera via this SW from any location within the net work.The Audivo video control software, allows you to view up to 4 cameras on one screen. The access can be limited to special defined users.The IP access gives the tools to store screen shots for documentation on the local HDD of the PC.
-
Product
48V / 200 Amp Load
EL12-48M
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with Telecom 48V Rectifiers and Power Supplies with output Voltages in the range of 38V to 60V and is extremely costeffective.
-
Product
Regenerative AC Load
61800
-
Chroma Power Electronics Test Solutions not only apply in the industries of Information Technology, Communication, Aerospace and National Defense, but also in energy efficient products such as Hybrid Automobiles, LED luminance devices, solar and fuel cells that are developed aggressively under the pressure of natural resource constraints. Chroma has a wide variety of instrumentation including AC Power Sources, DC Power Supplies, DC Electronic Loads, AC Electronic Loads, Digital Power Meters, and Automatic Test Systems that are ideal for power input/output terminal tests and dynamic simulation.
-
Product
Wireless LAN Network Analyzers
-
Collect radio wave characteristic data for WLAN and non-WLAN transmissions and translate them into an easy-to-understand web dashboard for network monitoring, operating, and troubleshooting.
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting Holes
LBC SERIES
-
The LBC Series (Load Button) load cells are offered for compression only applications where space is limited. The matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Counter bored mounting holes are provided for fastening down from the top. These sensors are manufactured from heat treated 17-4ph stainless steel and sealed for use in most industrial environments.
