Recording Systems
Equipment designed to make an automatic record of output from test equipment.
-
Product
Circuit Breaker Test System
TDR900
-
It operates and records a circuit breaker’s contact timing, motion, velocity, main contact engagement & synchronization, trip and close coil initiation and currents.
-
Product
Torque Converter Rebuilding Systems
-
Torque Converter Rebuilding Systems (TCRS®) from SuperFlow® are the choice of converter rebuilders worldwide for one reason: quality. The TCRS® system has been proven on more than 8-million torque converters and is in use at the big three automakers Ford®, General Motors® and Daimler Chrysler®. TCRS® sets the industry standard for precision alignment and is the only complete system available with all the tools to do the job right, with repeatability and precision within .001 of an inch. TCRS® representatives will help you select the correct equipment for your rebuilding goals. Every situation is different, but as a general rule, if you’re purchasing ten or more converters a day from an outside source an in-house converter rebuilding program from TCRS® will save you money.
-
Product
Gas & Flame Detection System
Syntel
-
Teledyne Gas & Flame Detection
Syntel is an addressable loop system suitable for use in zone 1 and 2 hazardous areas. The complete addressable loo is fault tolerant operating normally with a short or open circuit. Syntel does not have a CPU, so there is no common failure point. It includes a standard OPC interface and can also be supplied by Modbus allowing easy integration with third party systems.Syntel stores alarm and calibration information in distributed non-volatile memory, hence there is no reliance on a centralized system.Syntel is ideal for installations where there is the possibility for future expansion. The system architecture allows very low cost expansion as cable runs to a central location are not needed.
-
Product
PD Measuring System
TEM
-
Partial discharge test system for laboratory or on-site measurement according to VDE 0434, IEC 60270 and EN50178 consisting of:*Partial discharge meter TMG*High-voltage coupling capacitors for decoupling of the PD pulses*Partial discharge calibrator TPK for determining the correction factor in the PD test circuit
-
Product
Surface Resistance System Kit
PRS-801RM
-
- Perform Point-to-Point and Resistance to Ground Measurements from 0.01 Ω to 200 Teraohms- Accuracy of ±2% from 1.00 Ω to 9.99x1010Ω- Measures in accordance with ESD TR53, ANSI/ESD S4.1, ANSI/ESD S7.1, ANSI/ESD STM97.1 and others- Constant Test voltages 10V and 100V meeting ANSI/ESD S20.20- Operates using a Rechargeable Li-ion Battery Pack- Takes Approximately 8,000 Measurements on a Single Charge (480 hours typical)- Stores up to 999 Test Values Into Memory- Compatible with Prostat Connect 2.0 for Downloading into Excel®- Charging and Download via Standard Micro USB Cable- Includes 5lb Conductive Probes and Carrying Case- Certificate of Calibration Traceable to NIST included- 2-year Limited Warranty on Main Instrument
-
Product
AC Resonant Test System
-
Yangzhou Power Electric Co., Ltd
Testing of certain apparatus requires much high voltage or current that a straight AC test system is not sufficient. Thus resonant test reactor with a variable core is needed. The main advantage of such test systems is lower input power and larger output power. The resonant test system is designed to compensate capacitance in the testing circuit precisely by tuning inductance of the test system. AC resonant test system is used for factory testing of middle, high and ultra-high voltage cables, capacitors, generators, motors, power transformers and gas-insulated switchgears.
-
Product
Controlled impedance test system
CITS900s4
-
CITS900s4 is the seventh generation of Impedance test system from polar, and typically the most popular model for customers who are new to impedance control. CITS900s4 provides both differential and single ended measurement capability along with 4 channels to provide flexible probe connection.
-
Product
Multisample Rotation Type of Magnetization Measurement System
REM
-
This equipment is a new system of magnetization measurement equipment to arrange a large number of samples on circumference of disk, rotate the disk in magnetic field, detect derivative electromotive force in order generated by moving sample with detection coil, evaluate as magnetized amount after amplifying electromotive force and calculating it and measure continuously magnetization curve of a large number of samples with once magnetic field sweep.
-
Product
Torsional Vibration Monitoring Systems
-
Advanced Telemetrics International
Are used for Noise Vibration and Harshness (NVH) testing and analysis in automotive drivetrain, wind turbine gearbox and various other applications where measuring or monitoring rotating vibration is important. These systems are used to transmit torsional acceleration from a rotating shaft or component, while the machinery is running.
-
Product
Custom Engineered Motion Systems
-
Customizing our products and creating new motion designs for a specific application are at the heart of our business. With more than 50 years of experience, we’re the leading manufacturer of custom motion systems and equipment across a broad range of applications and industries. Whenever you integrate a customized Aerotech product or subsystem into your larger system, you can be confident that motion and precision will never be limiting factors in your success.
-
Product
Acoustic Scoring System
AcoustiScore
-
Provide realistic weapons training. Consisting of a sensor and a data reception and display unit, the system senses the shock waves from passing projectiles and converts these waves into electronic signals for miss-distance measurement and display.
-
Product
HPLC/UHPLC/SFC Systems
Nexera UC
-
Nexera UC improves your analytical workflow by utilizing a completely new separation technology, Unified Chromatography, which unites sample separation, analysis with various separation modes, and high-sensitivity detection.
-
Product
Dynamic Component Test Systems
-
RedViking brings advanced engineering and proven implementation expertise to your next dynamic component test stand. We’ve designed entire fleets of multi-model and single-model test systems for new component development and production as well as military and commercial MROs. We have decades of experience building and implementing turnkey dynamic component test systems, and we’ll work with your teams virtually anywhere in the world.
-
Product
Portable X-RAY Fluorescence Measuring System
FISCHERSCOPE® X-RAY XAN® 500
-
Mobile and universal handheld device for precise coating thickness measurement and material analysis - even with difficult material combinations.
-
Product
True Concurrent Test
TestStation Duo
Test System
The TestStation Duo is a true concurrent test system with independent test modules providing fast in-circuit test throughput and lowering high-volume production costs.It effectively doubles the test throughput of conventional in-circuit test systems, without doubling capital equipment costs or increasing manufacturing floor space, by combining two complete and independent test modules inside a single tester frame.
-
Product
Flight Safety Systems
-
L3 Cincinnati Electronics is a world-leader in range safety protection. Applications include missiles, unmanned aerial vehicles, heliostats and decoys. L3 CE is the provider of the next-generation flight termination receiver.
-
Product
Auto Charging System Analyzer
TE6-0606
-
Hangzhou Tonny Electric & Tools Co., Ltd.
This unit simply plugs into your car's cigarette lighter socket and will present you with alternator and battery status. On the left side is the alternator status indicating if it's charging the battery at too high a voltage, normal or too low. On the right is the battery status green LED charged 12.4-12.6V, yellow LED recharge 11.8-12.35V, and red LED dead<11.75V indicators.
-
Product
Gunshot Detection & Localization System
-
Information System Technologies Inc.
ISTI’s acoustic transient (e.g. gunshot or any other) event detection and localization technologies exploit low-cost distributed sensors with local processing capabilities. Key benefits include: better capture of muzzle blast and ballistic shockwave in urban environments, lower false alarm, real-time response, robustness to loss of sensor nodes, low hardware complexity, flexibility to configure a dynamic local network and ease in deployment. The Graphical User Interface (GUI) allows for control over the sensors and network while providing an overall assessment picture. Unlike existing gunshot detection and gunshot localization systems, the distributed sensing solutions (algorithms and hardware/software) developed by ISTI can support different sensors including acoustic, seismic and IR.
-
Product
GPS Synchronized Clock Systems
-
Signals & Systems India Private Limited
GPS synchronized clock system offers accurate time to all clocks in the system. The GPS clock synchronization system consists of a master clock and multiple slave clocks. The master clock communicates with all the salve clocks via wired/wireless medium in the system to provide them with an accurate time source. The objective of the GPS synchronized clock system is to make sure that all clocks in the system display the same time. Regardless of which part of the building you are in, the time shown by the clocks will be uniform and accurate.
-
Product
Fiber Optical Monitoring Alarm System
FOMA
-
FOMA (Fiber Optical Monitoring Alarm System) is integrated RTU (Remote Test Unit) 、Center Monitoring Server and its management software to achieve integrated operation、remote management、unattended monitor、periodic fiber scan、predictive analysis and support the instant fiber with status information and alarm warning, accurate of long-term fiber data record.
-
Product
Safety Radar System
-
Leuze electronic GmbH + Co. KG
The world's first safe 3D radar system, LBK from Inxpect S.p.A., was developed for the monitoring of hazardous areas in harsh industrial environments. It detects the bodies of persons and in doing so monitors the protected area for access and presence. Using the controllers, up to 6 sensors can be combined in one application.
-
Product
Mobile Cable Fault Location System
BAUR Syscompact 4000
-
Fault location with Syscompact 4000. The Syscompact 4000 is a compact, fully enclosed fault location system for pre-location and pinpointing of high-resistive, low-resistive and intermittent faults on low- and medium-voltage cables. Easy operation and the use of latest fault location methods enable fast and safe fault location.* Location of low-resistive, high-resistive and intermittent cable faults* Efficient cable fault pre-location methods* Pinpointing according to the noise location method or acoustic propagation time measurement* (with Universal Locator and ground microphone)* Sheath fault location according to the step voltage method (with Universal Locator and two measurement probes)* Easy to handle
-
Product
Optics Test Systems
Lens Test
-
Optik Elektronik Gerätetechnik GmbH
LensTest enables the measurement of air gaps, lens thickness, lens radii and lens surface centration errors in mounted lenses as well as the active alignment of lens surfaces during optics assembly for centering without rotating the assembly.
-
Product
Compact and Flexible Measurement System
Loggito
-
The Loggito series is a new compact and flexible measurement system for data acquisition Industry IoT. It enables inexpensive connectivity of decentralised measuring points for both low channel data logging and complex acquisition systems.
-
Product
Low Frequency Test Systems
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
Our imaging low-frequency inspection systems are excellently suited to displaying internal defects with high resolution and high dynamics.
-
Product
Vibration Test Systems
G-5 Series
-
Both Shock tests at from relatively high acceleration(max. 4900m/s2 -500G) to low acceleration with wide pulse width, difficult to achieve with conventional Shock Test Systems and Vibration tests for not only IEC, MIL and JIS but also requiring higher acceleration, velocity and displacement than ordinary VTSs can be carried out with one system.
-
Product
Mini Automatic Transformer Observation System
mini-ATOS
-
The mini-ATOS, is a professional multifunctional power transformer and substation diagnostic system. This compact and intelligent instrument can perform many routine and advanced tests such as Winding Resistance (WR), Dynamic Resistance Measurement (DRM), Turns Ratio (TR), Frequency Response of Stray Losses (FRSL), Magnetic Balance, and other diagnostic parameters. With the built-in fully automatic multiplexer, only a one-time connection is required for nearly all functions, which saves a considerable amount of time. The portable, rugged case is perfect for use anywhere onsite or in a laboratory. It is specially designed for fast and easy measurements with the well-known high precision and quality of all Raytech instruments.
-
Product
Equipment Failure Diagnosis System and Safety Management System
-
A system for diagnosing failures of rotating machinery such as turbines, motors, pumps, fans, and compressors, which are major facilities in nuclear power, hydropower, thermal power plants, petrochemical plants, shipbuilding, and aviation, through displacement sensors.
-
Product
System Layout
CARGOMASTER®
-
The parts that build up the system. Signal Control unit, the Computer Unit, Power Supply and Tank Sensors.
-
Product
System Modeling
-
Mentor Graphics SystemVision is a mixed-signal modeling and simulation environment using the power of VHDL-AMS and SPICE to verify your control and mechatronic systems. SystemVision includes graphical design entry, VHDL-AMS modeling and library tools, leading-edge simulation technology and powerful waveform viewing and analysis tools
