Recording Systems
Equipment designed to make an automatic record of output from test equipment.
-
Product
Battery Tester
CS-3001
-
The CS-3001 test system records all block voltages, total voltage and current during a discharge test. The modular design makes it easy to connect most of all battery installations, starting from a single block and ending up with 960 block voltages. Up to four parallel strings can be tested. All measuring modules are electrically isolated (600VDC CAT III, 5000VAC test voltage).
-
Product
Digital Fault Recording
SHERLOG
-
Fault recorder systems with a power quality analyser for comprehensively monitoring and assessing low, medium and high voltage networks in power plants and transformer substations. The measuring devices of the SHERLOG range make very high-resolution recordings of all the disturbances which occur in power supply systems. The behaviour of protection and switchgear devices during these system disturbances is recorded at the same time.
-
Product
Source Signature Recorder
-
*GPS accuracy for time break collection and source equipment locations.*32-bit, high speed, ADC chip for lower noise and increased accuracy for signatures.*Operates independently of crew, including observer and shooter or operators.*Can be used with any Vibrator Control System.*Great for monitoring rental equipment and operators.*Provides accurate start times that can be used with any nodal recording system.
-
Product
High-Resolution Seismic Recording System
DAQlink5
-
DAQlink 5 is the fifth generation of portable seismograph systems. It can be configured as a stand-alone monitoring system, a refraction system, or a distributed seismic reflection system.
-
Product
Event Recorders
-
Recording vehicle data is essential to operating and maintaining safe and efficient vehicles, and providing an effective health monitoring system. Recorded data provides vital information for accident investigations, train handling studies, fuel conservation, vehicle performance, and preventative maintenance programs.
-
Product
Multi-Channel Shock And Vibration Data Recorder
MSR-3C
-
Instrumented Sensor Technology, Inc.
The MSR-3C is a self-contained, multi-channel, digital acceleration waveform recording system. The system is battery powered, designed for field applications requiring multi-channel, extended time, unattended acceleration monitoring and recording.
-
-
Product
AIM System Solutions
System
AIM can provide a wide range of customized solutions:*Special-to Type Test Equipment (STTE)*High Level Bus Analysers (HLBA)*Data Acquisition Recording & Simulation Systems*Aircraft Ground Equipment (AGE)*MIL-STD-1760 Weapon Test Sets*Fibre optic MIL-STD-1553 Stub/ARINC429 Link Extension System (FoMIS/FoL)
-
Product
On-site Support
-
Aerodyn provide a complete field test service, offering on-site support at demanding and often remote test sites. We instrument test articles, route lead wires, configure data acquisition systems, record data, reduce data, and write test reports. We conduct tests on aircraft, in test cells, at power stations, aboard ships, and at manufacturing facilities.
-
Product
Intelligent Power System Recorder
iPSR
-
The iPSR™ is a 48 channel recorder (16 analog and 32 digital inputs) designed to intelligently record power system data. “Intelligently” does not mean compression. “Intelligently” means providing summary data allowing a quick identification of abnormalities combined with a fast download of the relevant data.
-
Product
Ultra High Productivity Solution
Universal Encoder 3
-
*Compatibility - UE3 is 100% compatible with the Force 3 system. Boards can be used as spares for the Force 3 system*Reference Flexibility - Multiple Digital and Analog References*GPS Discipline - GPS timing and assures starts on even sample boundaries for all continuous recording systems*Multiple Radio Support - UE3 can connect simultaneously to 4 High Speed TDMA radios. These multiple high speed radios assure reliable and efficient communication to all of the vibrator units used in High Production Vibroseis Mode*Digital Radio Support - UE3 supports the latest Digital Radios*Analog Radio Support - UE3 also supports legacy analog radios*Ethernet Radios Support - The UE3 includes support for low-power VHF-Ethernet radios. These radios have good speed and work well in many applications*Digital Radio Sims - Digital Radio Similarities are now available for UE3 and Force 3 or VibPro HD vibrator controllers*External USB Port - Use USB thumb drive to offload data from remotely operated UE3 units
-
Product
Modular Recording System
Xilinx Aurora
-
As a Xilinx® Alliance Program Member, Conduant is pleased to announce Xilinx® Aurora serial data transfer protocol compatibility with our flagship StreamStor® Modular Recording System.
-
Product
Portable Data Recorder System
PDR
-
Our Portable Data Recorder (PDR) is a low cost, lightweight data acquisition platform for lead paint inspection. It allows the inspector to efficiently identify and record inspection parameters without limitations.PDR interfaces with the Report Generation Software (RGS), streamlining data entry and allowing the inspector to produce instant inspection reports.
-
Product
High-Speed Signal Recording Systems
System
GaGe has a long history of providing high-speed, real-time signal acquisition, processing, and recording systems on PC-based platforms. This expertise saves customers time and eliminates uncertainties and risks with self-integrated systems.
-
Product
Software
SourceLink
-
Specifically designed to maximize production with Continuous Recording Systems like iSeis Sigma, OYO GSR, Fairfield Node, Sercel Unite and all other systems.
-
-
Product
Data Logger
Wind101A
-
The Wind101A is a complete system to accurately measure and record wind speed. This low cost wind speed recording system comes complete with the Pulse101A data logger, weatherproof enclosure, a three-cup anemometer and all the necessary cabling to quickly get up-and-running.
-
Product
Multi-Channel PCM Processing and Recording System with UDP Streaming
LS-68-M
-
The Lumistar LS-68-M Modular Multi-Channel processing and recording Telemetry Processing System offers an ultra-small, low-cost, high-performance, multi-channel COTS solution for PCM data synchronization, decommutation and simulation applications. Building on the legacy of the Lumistar LS-45, LS-50, LS-55 and LS70 series of products, the LS-68-M enhances the feature sets of each of these product lines and supplies them in a format requiring no hardware drivers in an “OS-less” environment. The LS-68-M utilizes a highspeed Gigabit Ethernet interface for primary controls and data streaming.
-
Product
IEC61850 Digital Substation Network Analyzer
PNA1000
-
PNA1000 is the professional 24-hours online monitoring and recording system, which could be installed in the digital substation to monitor, record and analysis the whole substation network communications system
-
Product
RF Acquisition Record and Playback Instrument
SARP-6
-
Saluki SARP-6 RF Signal Acquisition Record and Playback Apparatus is a portable RF signal acquisition record playback equipment. It can be used to directly acquire, record, and playback RF signal from 1MHz to 6GHz. Its data recording and bandwidth playback can reach 200MHz. The SARP-6 RF Signal Acquisition Record and Playback system is composed of up and down inverter module, high-performance ADC and DAC, and large capacity solid-state FLASH or high-performance disk. It is widely used in radar, GPS, communication, telemetry, as well as many other circumstances for civil purposes when acquiring signal and recording it down.Applications: Interference Analysis/Surveillance/Spectrum Management/Satellite Communications
-
Product
RF Signal Testers
-
RF Signal Generators, Record & Playback Systems, Players, Productivity Tools and More
-
Product
Power System Recorder
TESLA LITE
-
ERLPhase Power Technologies Ltd
The new TESLA LITE is an economical user-friendly multi-timeframe power system recorder: Economical yet complete power system recording for custom applications in smaller substations. Easy to use intuitive software Simultaneous transient fault, dynamic swing and trend recording and event logging Fault location derived from single and calculated currents IRIG-B clock synchronization (modulated and unmodulated) Smallest footprint among recorders allows easy retrofit and installation 12 current, 6 voltage and 38 digital inputs
-
Product
Portable Load Cell System
-
Load Cell is designed by Seismic Source Company to measure the Hold Down weight and the output force of the Servo Hydraulic Vibrator unit. The output of the Load Cells can be recorded with any accurate seismic recording system.
-
Product
Processing And Data Recorder Systems
DAQStream
-
DAQStream is a family of high-performance data acquisition and processing systems that combine Delphi Engineering Group’s industry leading wideband digital receivers and StreamServer™ – multi-channel, streaming software for unparalleled high-speed data recording and processing performance. Delphi’s wide variety of FMC, FMC+, ADC and DAC modules enable DAQStream users multiple configuration options to meet the most stringent application requirements.
-
Product
Fast Timing Analysis
Zero-Time Box
-
The Zero-Time Box is designed to compare the start times of source units with the recording system. It is compatible with every source encoder that outputs a start signal on a BNC connector, and also supports every source controller and decoder that does the same. The Zero-Time Box can also be used as a 5 channel precision measurer of timing intervals.
-
Product
Weight Registration System
-
The number of the current hopper and the correct positioning, along with the indication of power and status, are displayed on the indicators. Four load cells are mounted on the cart. The system records the amount of material shipped from each hopper, and the total weight of the material in the trolley is also displayed. All information is stored in the controller memory for a specified time. After the necessary time intervals, the operator can rewrite the information on the USB drive for further processing.
-
Product
Serial FPDP Rugged Rackmount Recorder
Talon RTR 2756
-
- Designed to operate under conditions of shock and vibration- Complete Serial FPDP record and playback system- Up to 8 I/O channels in a single 4U 19-inch rugged rackmount PC server chassis- Removable SSDs- Up to 38.4 terabytes of storage to NTFS RAID disk array- Copper, single-mode and multi-mode fiber interfaces available- Real-time aggregate recording rates of up to 5 GB/sec in eight-channel configuration- Supports Flow Control, CRC, and Copy/Loop Mode as a receiver and transmitter- Supports 1.0625, 2.125, 2.5, 3.125 and 4.25 GBaud link rates- RAID levels of 0, 1, 5, 6, 10 and 50- Optional N+1 redundant power supply- SystemFlow® GUI virtual instrumentation panel for fast, intuitive operation- C-callable API for integration of recorder into applications- File headers include time stamping and recording parameters- Optional GPS time and position stamping- Windows® 7 Professional workstation with high performance Intel® Core™ i7 processor
-
Product
Web Application Testing Tool
Sahi
-
Cross browser and Automated Regression Testing Tool: Record and playback any web application on any browser, any operating system. Recording saves time and helps non-technical users contribute to automation. The Sahi Controller helps easily identify and experiment with elements on any browser. The same script works on all browsers.
-
Product
Non-Multiplexed High Speed Continuous Function Card Overview
-
This type of system can be designed with benefits of both the multiplexed amplifier-per-channel and transient recorder systems. Benefits of the non-multiplexed amplifer-per-channel system include: High Sampling Rates: With an ADC per channel, the sampling rate is not encumbered with considerations such as multiplexing and post-amplifier settling time.Superior Filtering: With an ADC per channel, digital filtering can be used to augment analog filtering to achieve better anti-aliasing performance with much lower effective sampling rates.Superior Phase Matching: Digital filtering provides much steeper, more predictable rolloff rates and phase characteristics than analog filtering with greater stability with time and temperature changes at lower cost.
-
Product
Sequential Event Recorder
SER
-
The E-MAX Sequential Event Recorder (SER) is a highspeed,high-resolution, system which records relay andpower system equipment alarms and status contacts. TheE-MAX SER uses a fully isolated 16-point input card. The16-point layout isolates individual points from each other andfrom the system electronics by opto-couplers.
