RS485
Serial communication line supporting 32 devices.
See Also: Serial Communications, I2C, RS232, RS422
-
Product
Compact Protocol Analyzer
LE-1500R
-
"LE-1500R" is a protocol analyzer (line monitor) dedicated for asynchronous communication monitoring with affordable pricing. LE-1500R can run as a stand- alone by the internal battery for long time and can be remotely controled by a PC or a smart phone via Wi-Fi (Wi-Fi function is available only in USA, Canada, Japan, and EU). The analyzer has a TTL measurement port (which supports UART communication) as its standard port besides RS-232C, RS-422, and RS-485. It can monitor communication data of max 500Kbps for up to 32MB (8,000,000 data) in real time and also can execute a simulation testing of send/receive data. It also has a BERT function (which is not equipped with the analyzers of this pricing level) as its standard function. The correct time stamp, the measurement of idel time (which are the difficult for other software analyzers), and the capturing ability (without missing data) are the best options for trouble shooting and development test of a communication sytem which requires a reliablity.
-
Product
RS-232 to RS-485 Optically Isolated Interface Converter
Model 8322
-
FEATURES: 4 Wire-Master/Slave Operation; Active Mode Control Via RTS or Data; Opto Isolation; Built-in Power Supply; Internal Microcontroller; 38.4 KBPS Data Rate; DIN Rail Mountable; Programmable Terminations. The Model 8322 RS-232 to RS-485 Interface Converter allows information exchange in half duplex mode over two twisted pairs.
-
Product
Wireless Temperature Meter
WTM-100
-
●Measure accuracy:±1℃●Display range: -50.0~150.0℃●RS485 Modbus RTU communication port●Up to 12 channels wireless sensor connection●High stability and low cost●CE Approved
-
Product
Serial Interfaces
-
All of ICS's Serial Interfaces provide GPIB like IEEE-488.2 functionality over an RS-232 or RS-485 Serial link and are serial devices.
-
Product
PXI-8431/2 , 2-Port, RS485/RS422 PXI Serial Interface Module
778984-01
Serial Interface
2-Port, RS485/RS422 PXI Serial Interface Module - The PXI‑8431/2 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
GPIB-RS485/RS422 GPIB Instrument Control Device - Taiwan 110VAC
779733-11
GPIB Controller
The GPIB‑RS485 is an IEEE 488 controller device for PCs with RS485 or RS422 ports. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS485 or RS422 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS485 and RS422 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488, RS485, and RS422 standards, as well as interpret and execute high-level commands from the serial port, including serial‑to‑GPIB, and GPIB‑to‑serial protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
High-power DC Electronic Load (6kW~60kW)
FT68200A/AL/E Series
-
Shenzhen FaithTech Technology Co., Ltd.
FT68200 series high performance high-power DC electronic load provides three voltage ranges 150 V/600 V/1200 V, maximum current 2400 A per single unit, stand-alone power from 4 kW to 60 kW, expandable up to 600 kW, 10000A by master-slave paralleling. Ultra-high power density, 6kW is with only 4U height. Wider operating region, faster dynamic frequency, as well as transient mode, OCP/OPP test, sequence test, automatic test and battery discharge test functions greatly enhances its test strength and expands application coverage. Furthermore, two times instantaneous overpower loading capability can effectively reduces user’s test cost. Built-in standard RS232, RS485, LAN, USB (serial), optional GPIB and CAN interface, supports SCPI, ModBus RTU and CANopen protocol, which facilitates system integrators. FT68200 series has full protection functions, which can be applied to power battery discharge, DC charging station, charging piles, charging pile modules, vehicle On Board chargers (OBC), high-power switching power supplies, power electronics and other power electronics products.
-
Product
8K ip Camera Tester M-IPC-450C with TVI 5.0 Audio, Wrist Design
M-IPC-450C
-
Fuzhou Metricu Technology Co Ltd
8K wrist tester M-IPC-450C supports 8K ip camera, analog camera, 8MP TVI camera, 8MP CVI camera and 8MP AHD camera. (5 in one)It also supports DC12V 3A, 48V PoE 25.5W power output, UTP cable, RJ45 TDR cable, RS485, Audio in, TVI 5.0 audio, wrist design, etc.
-
Product
Serial analyzer
-
The Serial analyzer sink decodes analog data on a serial bus to serial data. It can be used to monitor and analyze RS232, RS485, MIDI, DMX or other compatible serial buses. The serial analyzer can monitor up to eight sources. When these sources are in sync (all sources are of one (combined) instrument), all captured data will be displayed in chronological order.
-
Product
4 2/3 Strain Gage Meter (1/32 DIN)
CS3-SG
-
CS3-SG Strain Gauge Indicator has been designed with high accuracy measurement, display and communication of DC signal 0~1.0/~4.0mV or 0~10.0/~40.0mV as like as Load Cell or Strain Gauge.The meter supports Field Calibration function. It can be calibrated with sensor(Load Cell/Strain Gauge) to meet machinery structure.They are also building in 2 Relay outputs, 1 External Control Input, 1 Analogue output or 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of machinery and testing equipments applications.
-
Product
- RS-422/485 DIN Rail Mounted Lightning/Surge Protector
Model 8022NX
-
FEATURES: Fast Response; Automatic Recovery; Up To 20 MBPS Data Rate; DIN Rail Mounted; Full Duplex; Triple Stage Protection. The Model 8022NX is a DIN Rail mounted surge suppressor for 4-wire RS-422 or RS-485 circuits used to protect factory data networks, or, any network that wants to avail itself of the DIN Rail packaging concept. The Model 8022NX provides common-mode (line to ground) surge protection and differential mode (line to line) protection for balanced networks. All the inputs, outputs and ground connections are via screw terminals located on the top surface of the device.
-
Product
RS232 Null-Modem Cable, DB-9 Female to DB-9 Female, 4m
182238-04
Serial Cable
9-Pin Female DB-9 to 9-Pin Female DB-9 Serial Cable - The 9F-9F Serial Cable, sometimes referred to as GPIB Serial Cable, connects and controls GPIB devices using RS232 and RS485 serial ports. The 9F-9F Serial Cable is offered in different lengths.
-
Product
Digital Panel Meter
VAW
-
VAW DC Multifunction Power Meter provide high accuracy measurement, display and communication of DC voltage, Current, Power, Energy(import / export), and Run Hour. They are also building in 4 Relay outputs, 1 Analogue output, 1 Pulse output , 2External Control Inputs and 1 RS485(Modbus RTU Mode) interface with versatile functions such as remote I/O, alarm and communication for DC power applications like as solar, wind power system or portable electronic device consumption testing.For the power saving, VAW has built in an innovation timer to switch down the light and power of LED. It makes sense to build the meter in a green power system.
-
Product
Firmware for High-speed Communication
OP-FW12GA
-
OP-FW12GA is the firmware to increase the speed of monitoring test of bit synchronous communication (such as HDLC/SDLC/X.25, or CC-Link communication), SPI communication, Profibus-DP (field bus known for high-speed communication), UART (asynchronous communication, which is commonly used). By processing great part of monitoring processes by FPGA, it unfailingly captures communication data with time stamps of a microsecond rate. The interface supports RS-232C/RS-422/RS-485/TTL.
-
Product
Mezzanine System
5033
System
ECM P/N 5033 provides eight channels of RS485 / RS422 I/O. The 110 ohm termination for each channel is enabled or disabled in software. Disabling termination saves power by eliminating unneeded or redundant termination. Speeds of up to 20 Mega bits per second are possible, but this design also features a 250K bits per second slower edge rate mode. The 250K bit mode is valuable when EMI is more of a concern and throughput is not important. All channels power up as inputs with the outputs disabled.
-
Product
Fixed Gas Detectors
MicroSafe 500 & 600 Series
-
Teledyne Gas & Flame Detection
MicroSafe 500 and 600 Series gas detectors feature a non-intrusive operator interface. Calibration and programming instructions appear in simple intuitive and sequential script on a 16-character backlit display. The transmitter design incorporates extensive fault diagnostics with each condition conveniently identified on the transmitter display.The 500 Series comes standard with a linear 4-20 mA output, one-man remote calibration, self-adjusting zero and span, and LED indicators for fault and calibration status.The 600 Series includes the same features as the 500 with the addition of 3 alarm relays and an RS-485 serial communications port.Electrical Classification - Explosion proofClass I, Div 1, Groups B, C, D
-
Product
Answer Man Junior I/O Board
0001-011
-
A general purpose interface board for Mircromint's Answer Man Junior. Jumpers select one of three communication interfaces (RS-232, RS-485, or fiber optic RS-232). 12 bit ADCs and DACs are added for higher precision AD conversions. Answer Man Junior is included with the board.
-
Product
Serial-to-Daq Card
Model 2307
-
* 2307 Board provides 32 digital I/O lines, 4 analog outputs, 6 analog inputs, 6 relay driver outputs and 4 temperature inputs.* Firmware supports ASCII command strings, Addressed commands for RS-485 networks and packet protocol. * Operates as a RS-232 as a RS-485 to Data Acquisition Board. * DE-9 connector has both RS-232 and RS-485 signals.* SCPI commands and IEEE 488.2 compatibility provide GPIB like operation over the serial link. * Runs on 5 Vdc power.
-
Product
Smart GPIB Serial Interface Board
Model 4816
-
* Provides GPIB-to-serial and RS-232-to-RS-485 conversion path for serial devices with RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
Product
Remote I/O
-
ADAM remote I/O are categorized into 5 families: IoT/OPC UA Ethernet I/O, Modular I/O system, RS-485 I/O and Serial/USB Converters/Repeaters.
-
Product
GPIB to Quad Serial Interface
Model 4896
-
* Provides four RS-232/RS-422/RS-485 Serial Channels.* High speed, 115.2 K baud channels include 60 K byte buffers.* > 600 K byte/sec. GPIB data transfer rate.* SCPI commands set serial configuration and GPIB address.* LCD display shows Bus activity, buffer status, serial interface signals and channel settings.* 1 U high rack mount kit mounts one or two 4896s * Includes US 115 VAC Power Adapter, Manual and Support CD.
-
Product
Serial to Relay Interface Boards
Model 2364 OEM
-
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Serial interface header includes RS-232 and RS-485 signals. * GPIB interface header includes GPIB address switch input signals.* Includes 50-pin mating relay connector and serial header connector.* Optional 115750 Terminal Board for easy connections without soldering.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel.
-
Product
GPIB Instrument Control Device
GPIB Controller
GPIB Instrument Control Devices offer IEEE 488 controllers that are compatible with ExpressCard, PMC, PCMCIA, PCIe, PCI, and USB slots as well as Ethernet, RS485, RS422, and RS232 ports. Some models can control multiple GPIB devices, and others offer sustained data transfer rates and no microprocessor interruption in data transfers. GPIB Instrument Control Devices include a license for the NI-488.2 driver software, providing maximum reliability for connecting to third-party instruments via GPIB. The devices are completely IEEE 488.2 compatible, have industry-standard transfer rates, and offer easy system configuration through NI software.
-
Product
CO Transmitter
DST1200
-
NDIR (non-dispersive infrared) waveguide technology CO measurement accuracy from 40ppm to 70ppm optional Varies measurement range available Optional analog signal or RS485 output Wide angle view LCD screen with CO readings in real time Toxicity and halogen free material, complying with GXP standard
-
Product
Analog & Digital Gas Controller
MX 32
-
Teledyne Gas & Flame Detection
We introduce the new MX 32, a controller that takes analog & digital inputs and covers all needs for a wide variety of applications.The MX 32 is a compact, low-profile controller that continuously monitors gas detection and more generally any 4-20 mA, MODBUS RS485 signal from compatible detectors.
-
Product
4 2/3 Digit Potentiometer Meter (1/32 DIN)
CS3-PM
-
CS3-PM Potentiometer Indicator has been designed with high accuracy, display, controller, remote communicationsA compact body design for small equipment, laboratory instrument, and others.Also are available with relay output, analog output, RS485 Modbus RTU communication to cover a wide range of applications.
-
Product
FaithTech FTLP Series 100W/180W Portable Programmable DC Power Supply
FaithTech FTLP Series
-
Shenzhen FaithTech Technology Co., Ltd.
FTLP series is a kind of programmable Portable bench DC power supply, with the widest output range, which allows engineers to test more program requirements with just one device. To be exact, the FTLP series provides full power all the way down to 25% of the rated output voltage. The FTLP series is equipped with RS232 and RS485 as standard interfaces that are essential for system integration, you can also choose USB or LAN interface as your add-on interface. The series supports SCPI and MODBUS-RTU protocol, which is convenient for all kinds of test platform. The FTLP series DC power supply can be widely used in battery chargers, high-voltage ultra-high-speed diodes, electrolytic capacitors, electromechanical control fields, and ATE test systems, etc.
-
Product
Network Analyzers
MPR6 Series
-
Dimensions:96X96kVArh, Max, Min: available (available) % THD I: available (available) % THD V: available (available)Harmonics 1-51.:RS-485:available (available)Digital Input:Digital Output:2AO:0/14-20mA: AO:0/2-10V:Relay:2 Pulse Output: available (available) Hour (RTC): available (available) Memory:1MB Pulse Counter: none (none) Operating Hour: none (none) Alarm: available (available) CT-25: none (none) 110/230 VAC:none (none) 85-265 VAC/DC: available (available) 45-265 VAC/DC: none (none) 10-56 VDC: none (none) Pcs. / Carton:8
-
Product
Analog Interface Boards
Model 4861B OEM
-
* 114578-24 board has 4 isolated analog outputs, 4 isolated analog inputs, 4 isolated drivers and 8 digital inputs* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any ICS GPIB Connector/Address Switch Assembly.* Runs on 12 Vdc regulated power.
-
Product
GPIB Smart Serial Interface
Model 4866
-
* Adds an IEEE-488.2 compatible GPIB Interface to any serial device.* Provides all IEEE-488.2 functions and a Status Reporting Structure for the serial device.* Uses SCPI commands to set the serial configuration, GPIB address and user's IDN message.* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals.* Operates with asynchronous serial devices, with standard serial devices and with 'smart' serial devices such as embedded computers or microprocessors.* 1 U high rack mount kit mounts one or two 4866s* Includes US 115 VAC Power Adapter, Manual and Support CD.
