RS232
A standard interface for serial binary data interchange defining voltage levels for logical one and logical zero, standard transmission speed and connector types.
See Also: Serial Communications, I2C, RS422, RS485
-
product
RS-232 to RS-485 Optically Isolated Interface Converter
Model 8322
FEATURES: 4 Wire-Master/Slave Operation; Active Mode Control Via RTS or Data; Opto Isolation; Built-in Power Supply; Internal Microcontroller; 38.4 KBPS Data Rate; DIN Rail Mountable; Programmable Terminations. The Model 8322 RS-232 to RS-485 Interface Converter allows information exchange in half duplex mode over two twisted pairs.
-
product
SIMRC - 8 x 4 Matrix 1-Pole Screened Relay
1030-R-8-4-1RF-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
HDMI Audio Extractor with Audio Amplifier, RS-232 and IP Control
EMX-I-AMP
The EMX-AMP is a 4K HDMI Audio Extractor with built-in 50 watt audio amplifier for direct connection of 8 ohm speakers. The device also provides line-level stereo Aux audio input and allows audio mixing of HDMI audio with the Aux input. Volume can be controlled from the front panel, RS-232, or external digital rotary pot (encoder) that can be mounted on a wall-plate.
-
product
3U VPX High Speed Video/Data Processing Card
iWave 3U VPX High-Speed Video/Data Processing Card is a rugged standalone module in the 3U VPX form factor, aimed for the high-speed data, video processing, and display applications is ideal for military, defense and aerospace applications requiring an optimal balance of performance and power efficiency. iWave 3U VPX High-Speed Video/Data Processing Card is implemented using Xilinx Kintex-7 device architecture and has I/O interfaces including High speed 16 channels of transceiver interfaces capable of operating up to 6 Gbps data rate, Gigabit Ethernet, RS232, RS422, PCIe interface, Built-in health monitoring circuits, HDMI input, and output interfaces
-
product
Ethernet Parallel Interface
Model 8113
* Provides 12 8CMOSL I/O lines for 3.3 and 5 volt logic.* 10/100 MHz Ethernet Interface with Auto-MDIX capability* Robust hardwired TCP/IP (Raw Socket) communication port prevents flooding, spoofing and injection attacks.* Included RS-232 serial control port for older systems.* Optional I2C port for connection to touchscreen panel or other I2C devices.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side.
-
product
Multiprotocol Serial Boards
104-COM-8SM-T
This is an eight-, four-, or two-port, asynchronous, serial communication board designed for use on the PC/104 bus. It supports RS-232, RS-422 or RS-485 communications. The board may be installed in any standard PC/104 stack. Connections are made via two 40 pin IDC type right angle connectors. Common applications include POS, gaming systems, machine monitoring, military and high-density networking.Type 16780 UARTS are used as the asynchronous communication elements.
-
product
SIMRC - 16 x Uncommitted Reed Relay, SPST Screened
1010-R-16-1RF-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
Amplifier
C-Band
Amonics offers polarization maintaining EDFAs for various applications. Including free space communications, coherent beam combining, and detection system. The output light is linearly polarized with high polarization extinction ratio. The compact turnkey benchtop or 19" rackmount instrument incorporates a user-friendly front panel housing with a LCD monitor display, key switch, power adjust control knob and optical connectors. A RS232 or Ethernet computer interface is also equipped.
-
product
Automatic Dielectric Constant Tan Delta And Resistivity
No Balancing and Calculation required to calculate Volume / Surface Resistivityand Dielectric Constant.Complies IEC 60250, IS 4487, Test jig Conform to ASTMD 257Built in Thermal PrinterSerial port RS232 for data downloading.Can be used to check liquid sample with Three Terminal oil cell.Storage 100 Test reports
-
product
RS-232 to RS-422 Interface Converter
Model 63-2SA
FEATURES: Full Duplex Signals; DTE/DCE Switch; TD and RD Indicators; DC to 115.2 KBPS. The Model 63-2SA provides a hardware conversion for full duplex signals between RS-232 and RS-422 I/O ports. Since the RS-232 port may look like a computer or a modem, the converter is equipped with a DTE/DCE selector switch.
-
product
Miniature Airborne Communications Converter
MACC II - Converter
Excalibur’s MACC II represents a third option. A proven, low risk, low cost, off the shelf product that translates between different communications specifications. The MACC II can solve your communications problems without R&D costs and without schedule risks while still providing you with the flexibility to customize the system to your specific needs.The MACC II is a wholly contained Miniature Airborne Communications Converter (data converter - protocol converter or translator). The MACC II can carry up to 4 modules. Each module can be one of the following protocols: 1 dual redundant MIL-STD-1553/1760 interface1 H009 channel5 MMSI channels5 ARINC-429 channels2 ARINC-708 channels2 ARINC-717 channels5 ARINC-825 (canbus) channels2 Serial channels (RS-232/422/485, NMEA 0183)Ethernet (10/100/Gigabit)10 Discrete I/O signalsAnalog to Digital / Digital to AnalogPlease see multi protocol 8000 modules for additional information on protocols that can be used on the MACC II.
-
product
Powered Crates
CAEN has decades of expertise in design and production of VME and NIM powered crates. The full line of crates is intended to guarantee reliability and mechanical solidity. CAN offers a selection of NIM, VME and Mixed Powered Crates with different configuration of power supplies and backplanes. Some crates can be ventilated with pluggable fan units, which also allow to have additional interfaces for remote monitoring and setting via CAN bus, Ethernet, USB and RS232.
-
product
COLORIMETER FOR SMALL DISPLAYS
K-8
The Klein K-8 tri-stimulus CIE Colorimeter Probe is designed to be the best colorimeter in sensitivity, stability and speed. It attaches directly to a pc's serial com port (RS-232), and runs with the companion pc program. Whether a desktop or a laptop is used, the Klein measurement application is in control and many additional features are available.
-
product
Datalogging Light Meter (RS-232)
DLM 536
Spectrum of photo sensor meets C.I.E. photopic curve V(l). 16000 Records Data logging capacity. RS-232 interface (software included). Measurement of luminous intensity(PC Software)
-
product
30MHz Arbitrary Waveform Signal Generator
Model AWG30D
- 4.3′ High Resolution TFT LCD Display- Two Independent Channels Output, Same Characteristic- 1μHz Frequency Resolution for whole range- 120 MSa/s Sampling Rate, 14 Bits Vertical Resolution- 5 Standard Waveforms, 50 Built-in and 5 User-defined Arbitrary Waveforms- FM, AM, PM, PWM, Sum, FSK, BPSK and SUM Modulation, Sweep and Burst Function- Channel Coupling and Combine Features On CHB- Build in 350MHz Frequency Counter- Arbitrary Waveform Edit PC Software- Standard Interface: USB Host, USB Device and RS-232
-
product
Four And Two-Port Multi-Protocol RS-232/422/485 M.2 Cards
M.2-COM-4SM Family
The M.2-COM-4SM family of cards feature high performance 16C950-class UARTs. Available in 4-port and 2-port versions, each port is capable of communication speeds up to 921.6kbps in RS-232 (differential modes support speeds as high as 3Mbps) and has 128-byte deep transmit and receive FIFOs. Large FIFOs protect against data loss in multitasking operating systems, reduce CPU utilization, and improve data throughput, while reducing or eliminating inter-character or inter-packet pauses. The advanced integrated circuit with pre-scalar supports a wide variety of custom baud rates, and any rates not otherwise achievable can be supported via a custom factory-installed crystal oscillator (up to 10Mbps!).
-
product
DC Sources
Electronic Test & Power Systems
Adjustable constant voltage and constant current sources are provided across the entire DC source range. Additionally constant power operation is standard on the high power DC supplies and optional on the medium power models. Modular high current DC power supply systems providing up to 2kV at 2MW can be assembled.A variety of interfaces are available. Analogue, RS232, CAN, RS485, Ethernet or IEEE 488.2 can be specified for most units. LabVIEW drivers are also offered to aid system integration.
-
product
- RS-232 to RS-422/RS-485 Converter
Model 285
FEATURES: User Selectable RS-422 or RS-485; User Selectable 2 or 4 Wire RS-485; Intelligent Control Of RS-485 Transmitter And Receiver; TD & RD LED's; DTE/DCE Compatible; Data Rates Up to 64 KBPs. The Model 285 RS-232 to RS-422/RS-485 Converter is a unique interface converter that can be configured to operate in compliance with RS-485 or RS-422 equipment, and RS-232.
-
-
product
PXI 36 Channel Data Comms MUX, 96-pin SCSI
40-735-912
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. This 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
product
PXIe-8430, 16-Port, RS232 PXI Serial Interface Module
781472-02
16-Port, RS232 PXI Serial Interface Module—The PXIe‑8430/16 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
PCIe-8430, PCI Express, 2-Port, RS232 Serial Interface Device
782122-01
The PCIe‑8430/2 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard … COM ports for compatibility with programs that use serial communications.
-
product
Encoding Altimter/Altitude Digitizer Decoder
TA-600
This is a small portable micro controller based altitude decoder that utilizes a two line by twenty-character dot matrix VFD type display. Tracking rates of up to 20,000 fpm are provided and a special screen dump of real time data is provided via an RS232 output.
-
product
Electronic DC Load, 80V, 80A, 400W With/without Remote Interfaces
LD400 Series
Versatile solution for testing dc power sourcesConstant current, resistance, conductance, voltage and power modesWide voltage and current range, 0 to 80V and 0 to 80A400 watts continuous dissipation at 28°C (360W at 40°C)600 watts short-term dissipation (up to 60 seconds)Low minimum operating voltage of <1V at 40AHigh resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminals (front terminals 30A max.)Full bus control via USB, RS232 and LXI compliant LAN interfaces (LD400P)GPIB option (LD400P only)
-
product
Electronic Surveying Compass
TOPOSENSOR
F. W. Breithaupt & Sohn GmbH & Co.KG
*Compact electronic surveying compass*Internal memory for storage of approx. 4.000 measurements*RS232 interface*Digital LCD readout of horizontal/vertical angles; disply 1°*Declination setting*Scope magnification 10x*Accessories upon request
-
product
LEAK TEST MANAGER SOFTWARE
Leak Test Manager is a software application for PC compatible with Windows XP, 7, 8 and 10 that allows interfacing ForTest equipment to a computer via an RS232 connection (or Ethernet if optional is available on the instrument)
-
product
Mid-Range Gas Filter Correlation Carbon Monoxide Analyzer
Model T300M
The Model T300M CO analyzer measures low to mid ranges of carbon monoxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO filled chamber and a chamber with no CO present. The light path then travels through the sample cell, which has a folded path of 2.56 meters.The energy loss through the sample cell is compared with the span reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing excellent performance from low to high range.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T300M comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
product
cRIO-9038, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, and Extended Temperature, 8-Slot CompactRIO Controller
783850-01
1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, and Extended Temperature, 8-Slot CompactRIO Controller - The cRIO-9038 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application development. The cRIO-9038 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, two USB host, one USB device, and two RS-232 serial. Additionally, the cRIO-9038 supports an extended temperate range. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
RS232 I2C Adapter LowPower
*I2C frequency adjustable up to 100kHz*Maximum power consumption <5mA*Interrupt input for external events*Simple software interface (ASCII commands)
-
product
Datalogging Digital Sound Level Meter with RS-232 Software and Cable
735
Whether you are testing for OSHA compliance, quieting equipment, or monitoring the roar of a stadium crowd, B&K Precision's Sound Level Meters can get the job done. The model 735 Sound Level Meter provides 30~130 dB capability in three convenient measurement ranges Low, Med and Hi with an accuracy of ±1.5 dB. The meter meets the IEC 651 Type II and includes frequency weighting A & C and fast and slow time weighting.
