Mains
chief conduit of electricity, gas or water distribution.
-
product
VLF Diagnostics System
PHG 80 TD
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PHG 80 TD. The combination of the PHG 80 programmable test generator with the BAUR dissipation factor measurement system produces the cable testing and diagnostics system PHG TD. It is operated via PC control. Dissipation factor measurement and diagnostic testing sequences can be programmed in the menu, after which the dissipation factor measured values are automatically determined in various voltage steps and a final evaluation is conducted.* Biggest dynamic range of tan delta measured values from 1 to 10-4 with a cable capacitance >10 nF to 20 uF* High resolution +/- 1x10-5 applicable even in new PE/XLPE cables* Insensitive against interferences due to complete mains separation* Lowest time required for assessing a medium-voltage cable (3-phase approx. 1 hour)
-
product
Waveform Generation Toolbox for Wideband Signal Simulation
N7509A
The Waveform Generation Tool provides a simplified interface for baseband modulation of Keysight's wide bandwidth signal simulation solutions, for signals with up to 1 GHz RF bandwidth. Even the most complex signals are defined and implemented easily through the software interface. Signals can be defined through basic parameter entry or from files created in MATLAB or other engineering environments. For each selection in the main menu, a subsequent screen appears, enabling the user to enter the parameters required to define the waveform and invoke the built-in calibration routines. A display on each sub-panel shows the ideal frequency domain waveform calculated from entered parameters. A simulation mode is provided to enable development and operation without connection to the instrument hardware.
-
product
EMC Analyzers
Mains and harmonics analyzer and associated low distortion AC power source for EMC measurements to EN61000-3-2 and EN61000-3-3.
-
product
Split type AC Current Sensor
CTF-600A
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Suitable for current measurements of main cable. * Wire stopper is equipped for the slipping protection. * The special connector is not necessary as the output terminals are provided. * Open circuit protection and nonflammable plastic material.
-
product
6U CompactPCI® Rear Transition Board for MIC-3396
RIO-3316
The RIO-3316 is the first Rear Transition Module (RTM) supporting PCIe connectivity to the main CPCI board enabling significant value-added features and extensions to next generation CPCI blades such as MIC-3396. The RIO-3316 supports: one PS/2 port, one USB 3.0 and one USB 2.0 ports, one RS-232/485/422 ports, two Gigabit Ethernet ports, two PICMG 2.16 LAN ports, one digital and one integrated (digital/analogue) DVI port on the rear panel. One UHM connector on J3 provides PCIe bus and allows supporting USB 3.0 and SATA Gen III (6 Gb/s).
-
product
MFP-570 Main Fuel Pump
The MFP-570 provides main engine burn flow as well as servo flow and engine actuator flow. This two-stage “cartridge type” fuel pump is designed to be inserted directly into the engine fuel metering unit.
-
product
Multi-purpose Tester
DEL-101
Standard Electric Works Co., Ltd
● Mains wiring polarity check.● ELCB/RCD testing.● Measuring ear for line current.● Measuring ear for leakage current.● Helps calculate insulation resistance.● Helps calculate power consumption.● Helps fault finding of standing earth fault.● Fused main adapter.● Appliance testing (with the aid of a clamp meter).● Fused appliance socket.● No batteries required.● HRC fuse inside.● Fused, color-coded universal test sockets.● Universal mains IEC Lead.
-
product
Land Platform Inertial Navigation Unit
Epsilon™
Versatile, Epsilon™ family provides advanced applications, even in GNSS denied environment: navigation (position & heading), aiming aid, driving aid. It covers all tactical applications from logistic to infantry fighting vehicles, as well as main battle tank.- Can be integrated with small artillery caliber to provide precision pointing- Connectable to any Battle Management system- Immune to magnetic disturbances
-
product
Copy Tools
DemiXG1020
Main unit weight is approx. 1.4kg, ultra compact and thin designResults in superior portability, perfect for on-site copying, backup, and data deletion.High speed data transfer at 10GB per minute (*1).(*1 Transfer speed varies according to performance of connected devices.)Reverse copy functionCan copy from last portion of HDD. Perfect for restoring data.Built-in evidence preservation functions including hash generation (MD5, SHA1, and SHA256) and creating DD images, etc.Built-in deletion function and quick diagnosis functionDeletion report can be created using host software (sold separately).
-
product
Micro Vickers Hardness Tester
Sinowon Innovation Metrology Manufacture Ltd.
◆ MicVision main use in testing materials allows for the measurement of the hardness of small or thin specimens and small areas of larger specimens, MicVision testing is commonly used to determine characteristics of thin sheets, foils, fine wire, epoxies, paints, etc. and is often employed in R&D applications .◆ MicrVision hardness is especially useful in determining hardness variations, caused by hardening, quenching, plating, fabrication, welding or annealing, bonding, etc. Micro hardness testing can be accurately employed using loads as slight as 10 gram, somewhat less and considerably more in certain situation.
-
product
Electronic Loads
The DSO and DSOT series electronic loads are designed using advanced linear technology.The DSO series offers two main functions: constant current and constant resistance. However, these loads can absorb full power between 20% and 100% of the acceptable input voltage thanks to the autoranging mode.For more extensive requirements, we offer 'DSOT' models that also include constant voltage and constant power functions. These functions are essential for testing voltage generators such as automotive alternators or photovoltaic panels to determine their power curve. In addition, DSOT models have a basic '0 Volt' characteristic, which means they can be used with input voltages as low as 0 Volt. However, they still maintain a high reaction speed, which can reach 1V/us and 8A/us.
-
product
Counter Electrodes
For a system using a three-electrode potentiostat, we measured current when a potential is applied between the working electrode and the reference electrode. Passage of current through an electrical circuit requires electron transfer reaction between the working electrode and the counter electrode.The main function of the counter electrode is to provide the location of the second electron transfer reaction. Important parameter of the counter electrode is the surface area. It is required (area) large enough to support the current generated for the working electrode. For example, the surface area of the platinum electrode of 5 cm is sufficient to use as an electrode, such as steady-state cyclic voltammetry experiments. However, for generating a high current measurements such as bulk electrolysis, the counter electrode of a larger area is required, as Catalog No.012961 which the length of platinum is 23 cm. This electrode is used for measurement, such as rotating ring disk.
-
product
4x 3U OpenVPX MOSA Remote Interface Unit
SIU34-RIUVARM-01
SIU34-RIUVARM-01 is a Modular Open Systems Approach (MOSA) Remote Interface Unit (RUI) to manage, monitor and control connected I/O, communications, measurement and simulation interfaces through Ethernet commands from a main mission processors. Extremely low power with 2 x 10/100/1000Base-T Ethernet.
-
product
Beam Directional Power Supply Mains
SiteX CP160D
The CP160D is the lightest and most compact generator of the CPSERIES. Featuring a built-in Beryllium window, it is the perfect generator for the inspection of light alloys such as aluminum, magnesium or fiber based materials like glass and carbon, as well as the greater thickness of steel. In fact, with its penetration capacity that is capable of reaching up to 37 mm of steel, the CP160D is able to execute many different types of NDT tasks without the need to ever have to add extra accessories.
-
product
Robotic Intelligent Laboratory System
CHANGSHA KAIYUAN INSTRUMENTS CO., LTD.
Is able to determine calorific value, total sulfur, internal moisture, ash, volatile matter, CHN content and other indicators by robot technology. The main components include intelligent robot, automatic analytical instruments (calorimeter, sulfur analyzer, proximate analyzer, and elemental analyzer), automatic bottle opener and sampling device, automatic weighing device, oxygen vessel loading and cleaning device, electrical control system, and laboratory analysis and data management software.
-
product
Handheld TDR / Cable Fault Locator
RapidTrace 1100
*This TDR / Cable Fault Locator is suitable for testing all Communication CAT (3-6) , Power Cabling , coaxial and mains power cabling*The RapidTrace 1100 TDR / Cable Fault Locator has a 11 measurement ranges from 0.5m to 3500m (3.5km) and is accurate to 1%*The TDR / Cable Fault Locator has 25, 50, 75 & 100ohm Selectable Cable Impedances*Using pre determined gain and pulse width on the TDR / Cable Fault Locator, all major operating and setting parameters can be easily accessed
-
product
LAN Tester
TVR10/10/100
Triplett Test Equipment & Tools
TVR10/100/1000 LAN Tester is comprised of a "Main unit" and a "Remote Probe". The Main unit performs the bulk of the tests, such as determining the LAN device type (is it a hub/switch or PC?), the LAN speed and duplex (10, 100, 1000 MB/s, half or full duplex) and whether PoE (Power over Ethernet) is present without the need of the Remote Probe. The Remote Probe adds the ability to trace cable locations (by audibly tracing tones placed on the cable by the Main Unit) and to test the wiring of the cable (by decoding and displaying wiring information placed on the cable by the Main Unit).
-
product
With CATV RF Input EDFA
HA4600/RF
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA4600/RF series is the narrow-band multiplexing EDFA which suitable with CATV application. This EDFA build-in one unit 1550nm direct modulated CATV transmitter used in inter cutting local VAD service. Build-in WDM multiplexing TX optical signal and External input optical signal of the main road then enter EDFA amplification, to server the local users. In order to avoid TX output optical power and the external input optical power does not fit the main road interfere with each other, the output power of the TX through the build-in VOA, from front panel adjust and set. The whole unit is concision, install and debug convenient. Providing high-quality, low-cost solution for all-optical relay 1550nm optical CATV systems, second-grade service area or administration village inter cut local VAD service.
-
product
6x 3U OpenVPX MOSA Remote Interface Unit
SIU36-RIUVARM-01
SIU36-RIUVARM-01 is a Modular Open Systems Approach (MOSA) Remote Interface Unit (RIU) to manage, monitor and control connected I/O, communications, measurement and simulation interfaces through Ethernet commands from a main mission processors. Extremely low power with 2 x 10/100/1000Base-T Ethernet.
-
product
Stainless Steel Junction Box
JB104SS
The JB104SS junction box model is designed to connect and trim up to four load cells per board. It may also be used in combination with additional juction boxes through the use dof an expansion port on the main board to connect multiple junction boxes thus allowing the summing of more than four load cells.
-
product
2nd Generation PCI Multi-function Decommutator
LS-50-D
The Lumistar LS-50-D PCI Multi-function PCM Decommutator offers a PCM decom, PCM simulator, time code reader/generator, and optional bit synchronizer in a single short PCI card slot. The multi-function decom and simulator are implemented in FPGA using a next generation design based on the LS-50-P. The simulator, decommutator, time code reader and time code generator are achieved on the main board and the bit synchronizer is achieved through an optional low-profile daughterboard. CVSD voice decoding, h.261 video decoding, and IRIG Chapter 8 decoding are achieved through software.
-
product
RFID Sensor Transponder (HF)
TELID®200
With the TELID® 200 range, you can have a combination of RFID transponders and sensors for measuring physical quantities. Here, in particular, pressure, acceleration, strain, moisture, and electric conductivity are of significant interest. Determining the situation just-in-time and storing the newly measured values in the integrated memory is one of its main functions. More complex functions such as digital I/O ports for connecting memories, microcontrollers and digital subsystems are also available. TELID® 200 products do not require batteries and work with no internal energy source.
-
product
Lamp Converters
PeakTech Prüf- und Messtechnik GmbH
This AC / AC voltage converter is particularly suitable for use with halogen indoor lights and other low-voltage light sources that require an AC voltage source for supply. There is a safe galvanic separation between mains and low voltage according to the isolating transformer standard. This pre-assembled AC / AC converter is equipped with an overtemperature switch that cannot be reset.
-
product
High Power Dry SIL Reed Relays
Series 114
SIL relays - Will replace mercury wetted relays in some applications. 1 Amp switching, 2 Amps carry. AC Mains voltage switch.
-
product
ATSC/DVB-T/QAM VHF/UHF Modulator For PCI
DTA-112
Cost-effective variant of DTA-115 with 75-Ω BNC main output and support for ATSC, QAM-A/B/C and DVB-T.
-
product
Ultrasonic Thickness Gauge
MX-5 DL
The MX-5 DL is a simple to operate Ultrasonic Thickness Gauge with an internal data logger. It offers features that make your job easier. An Alarm mode, Differential mode, high speed scanning, and data send are the main features of the MX-5 DL. The MX-5 DL will automatically log your readings in numeric order ( 1 to 1000 readings ). The gauge comes as a complete kit, ready to use, and is backed by Dakota Ultrasonics 5 year limited warranty.
-
product
3D Geo-Magnetometer
For the measurement of magnetic equilibria such as the earth's magnetic field, for the determination of anomalies and biologically active location factors. Three highly sensitive magnetic field sensors, as well as a dedicated microprocessor, are integrated into the measuring probe. The sensitive magnetic field sensor is connected to a PC, notebook or laptop (not included). The main features in brief:
-
product
Software
Photometric Solutions International Pty Ltd
PSI’s main focus is on the design and development of quality photometric equipment. We write all of our own software for the control of the equipment, interfacing devices, data acquisition, user-interface and report generation.
-
product
Integrated Safety Unit For ATOS
ISU-R
Raytech Integrated Safety Unit is a useful device when creating rack mounted transformer observing systems. It supplies Raytech devices with fused electrical power, manages external Interlocks and provides a single interface for an external warning lamp. The whole system can be turned on and off with a single mains switch.
-
product
MIL-STD-1553 Modules
> MIL-STD-1553B is the military specification defining a digital time division command/response multiplexed databus. The 1553 databus is a dual-redundant, bi-directional, Manchester II encoded databus with a high bit error reliability. All bus communications are controlled and initiated by a main bus controller. Remote terminal devices attached to the bus respond to controller commands. MIL-STD-1553B defines specifications for terminal device operation and coupling, word structure and format, messaging protocol and electrical characteristics.





























