Dielectric
-
Product
Downconverter for the 21cm Bandvalon
2100
-
1440MHz inputLow noise figure LNA 0.3dB 20 KHigh gain >40dB8-pole ceramic dielectric input filterHigh dynamic range, low-spurious responses Rugged milled aluminum housingRFI shielded constructionDesigned for use with Valon 5009 as LOSuitable for hydrogen line observation and general radio astronomy in the 21cm band.6Vdc @ 400mAIncludes 20” dc power supply cable
-
Product
Handheld Moisture Meters
-
Since water has a dielectric constant considerable higher than any other material, even a small amount of water in a product will cause the combination dielectric constant to increase substantially. Finna Sensors' capacitance meters can easily recognize this increase in water content and are programmed to display the result in direct reading percent moisture content.
-
Product
Full Band Phase Shifters
STP-18-10-M2
-
Full band phase shifters are micrometer-driven, waveguide-based phase shifters. The configuration of the micrometer-driven phase shifters is similar to that of level setting attenuators, where the phase shifting is caused by an E-plane dielectric insert in the rectangular waveguide. The amount of phase shifting is directly dependent on the volume of the insert. The VSWR and the insertion loss of these phase shifters are dependent on the frequency. The below standard offering covers the frequency range of 18 to 110 GHz and a phase shifting range of 180 degrees. These micrometer-driven phase shifters are typically used to introduce a certain amount of phase shifting when the absolute number is not a focus.
-
Product
Microwave Cavity Characterization
-
Material Sensing & Instrumentation
Microwave cavity characterization complements TDR Dielectric Spectroscopy in low-loss materials, providing high-resolution permittivity and loss data at specific single frequencies. Since measurements do not change significantly with frequency in low-loss materials (Kramer-Kronig relation) cavity measurement at select frequencies provides a full characterization across the RF/microwave range.
-
Product
Tangent Delta And Dissipation Factor Measurements
-
Designed for high accuracy and reliability, it simplifies testing processes and ensures compliance with industry standards in a variety of sectors, including power and energy for high-voltage equipment testing, manufacturing for capacitor quality control, research and development for advanced dielectric material studies, and utilities and maintenance to ensure power system performance.
-
Product
Partial Discharge
-
Is a localized dielectric breakdown (DB) (which does not completely bridge the space between the two conductors) of a small portion of a solid or fluid electrical insulation (EI) system under high voltage (HV) stress.
-
Product
Multi-layer PCB
-
Teledyne Labtech has established considerable technical knowledge and manufacturing experience in the supply of complex microwave PTFE and Mixed Dielectric Multi-layer PCB. From simple multi-layer structures through to complex metal-cored PCB, Teledyne Labtech can offer the complete solution.Teledyne Labtech has a policy of continuous investment and now boasts a capability that can meet the most demanding RF/Microwave requirements. Teledyne Labtech can offer blind and buried, plated through vias (THP), laser cut cavities, embedded resistors and connectors.
-
Product
Loss Tangent M in Dielectric Oil
TAND220A
-
The measuring instrument type TAND220A complies with the international standard IEC 61620. The instrument is based on the so-called "low-amplitude, low-frequency alternating current square wave method" and allows accurate measurements of conductivity and relative permittivity. Conductivity measurement in the range of 0.01 pS/m to 20,000 pS/m allows the use of this instrument for quality control of high resistivity liquids even at room temperature. The TAND220A works with a low test voltage and also with a low test current so that it does not represent a danger for the operators.
-
Product
Dielectric Withstand Tester
-
Weshine Electric Manufacturing Co., Ltd
The induction withstand voltage test of transformers and transformers is an important test to ensure that the quality of transformers conforms to national standards. The longitudinal insulation induction withstand voltage test of the inter-turn, inter-layer, inter-section and inter-phase insulation of the transformer winding is an important item in the transformer insulation test.
-
Product
Manual Dielectric Constant, Tan Delta & Resistivity Test Set
-
*AC and DC test Voltages switched internally.*Direct digital display of test voltages.*Auto ranging and direct read out of volume resistivity.*Cell constant adjustment and Tan Delta zero correction.*Built-in protection for test sample flash over.
-
Product
Insulation Resistance Measurement
MD 5060x
-
The Megabras MD-5060x is a smart, microprocessor-controlled, 5kV insulation tester and analyzer. Besides the conventional measurement of insulation resistances up to 5 TW, its advanced features allow to automatically measure both the Polarization Index and Dielectric Absorption Index, thus significantly simplifying testing of transformers.
-
Product
A C DIELECTRIC STRENGTH TESTERS ( HIPOTS )
AVC-50V
-
A C DIELECTRIC STRENGTH TESTERS ( HIPOTS ).
-
Product
AC Resonance Test System
-
KV Hipot Power Test Equipment Co.,Ltd
KVXZ-270kVA/270kV Variable Frequency AC Resonance Test System is applied for AC dielectric test for electric equipment.
-
Product
Decade Capacitor
1419 Series
-
GenRad 1419-A and GenRad 1419-B (Polystyrene) Owing to its very low dielectric absorption, the GenRad 1419A 3 Decade 1000 pF/step & 1419B 4 Decade 100 pF/step Polystyrene Decade Capacitors are particularly useful in research and development work on computer and integrator circuits and on low-level amplifiers. Its constancy of capacitance and dissipation factor as a function of frequency also makes it extremely useful in measuring circuits and as a component in filters and tuned circuits. High insulation resistance and low dielectric absorption make it the 1419 Decade Capacitor a nearly ideal capacitor for dc work.
-
Product
50 Ohm SMA 1.0-110GHz
-
50 Ohm 1.0mm-to-1.0mm (often referred to in micro-wave contexts as "SMA 1.0" or W-band) cable assemblies are ultra-high-frequency, precision coaxial cables designed for 1.0 mm connectors operating from DC to 110 GHz. They use a 1.0mm diameter outer conductor, air dielectric for low loss, and are used for sub-Terahertz millimeter-wave applications.
-
Product
Diode Submounts
-
Ultra-precise patterning of thin film metals on dielectrics with high thermal conductivity are used for diode submount applications. Via the acquisition of Ion Beam Milling, Inc., SemiGen is the industry leader for laser diode submount fabrication. As each application is different, we work with customers to develop a custom design that perfectly fits their requirements. We have experience producing circuits utilizing substrates of varying thicknesses with high thermal conductivity such as alumina (Al), aluminum nitride (AlN), and beryllium oxide (BeO). SemiGen can deliver laser diode submounts with or without Au/Sn pads depending on your needs.
-
Product
Three Cups Insulation Oil Dielectric Strength Tester
STY Series
-
Chongqing Assen Power Equipment Co., Ltd
STY series three cups insulation oil dielectric strength tester uses a microprocessor to automatically complete boost, keep stirring, static discharge, calculate, print and other operations, is a necessary measure in the conventional test equipment.
-
Product
Optical Voltage Probe
400-02
-
Srico’s optical voltage probe uses advanced, proprietary optical chip technology to achieve precise, interference-free measurement. Our sensor and optical fibers are made of dielectric materials. This facilitates a high degree of isolation between the voltage test point and the instrumentation system ⎯ at a safe distance of 100 meters and more. This system senses, measures, and transmits electrical data very accurately.
-
Product
Materials Measurement Suite
N1500A
-
With Keysight N1500A materials measurement software suite, you can determine the intrinsic electromagnetic properties of many dielectric and magnetic materials. The complete system is based on a versatile Keysight network analyzer which measures the material’s response to RF or microwave energy. The N1500A software controls the network analyzer and calculates results. Depending on the Keysight network analyzer and sample holder or fixture used, frequencies can extend from a few hundred MHz into the low THz.
-
Product
Insulation Testing
-
Weshine Electric Manufacturing Co., Ltd
Insulation is one of the most important constituents of a transformer. Any weakness in the insulation may cause failure of transformer. To ensure the effectiveness of the insulation system of a transformer, it must confirms the dielectric test. But the power frequency withstand test alone can not be adequate to demonstrate the dielectric strength of a transformer.
-
Product
Terahertz Spectroscopy Solutions
STRIPP Control IM
-
Teratonics offers innovative solutions for contactless non-destructive testing and imaging inside dielectric materials and on coated metallic surfaces. Based on the patented technology and our profound know how on its application, we offer: ► Instruments for product and process control as well as for inspection with automated evaluation ► Laboratory services for industrial R&D, fatigue tests, maintenance, end of life studies
-
Product
Oil Resistivity Test System / Million Meg Ohm Meter (MM1)
OTD-45
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Model : OTD-45OTD-45 is single self contained unit containing oil test cell, high frequency induction heating with temperature controller/sensor; dielectric loss measuring bridge, AC test voltage source, SF6 filled standard capacitor; high resistance meter; DC voltage source and all digital circuits.
