Exhaust Test
See Also: Exhaust
-
product
Test Sockets
Yamaichi Electronics Co., Ltd.
A test socket is the ideal point to test your home’s internal phone wiring for faults. You can also use it to identify any potential faults with the phone line outside. Your test socket is located in your master socket. It is the point between the internal phone wiring in your house and the phone line outside. That means by plugging into your test socket you can bypass all the internal wiring and test your device directly on the phone line.
-
product
Primary Injection Test Systems
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
product
Load Testing Platform
NeoLoad
NeoLoad is the only load testing platform covering you for both Cloud-ready apps, microservices architected apps, mobile and IoT apps and enterprise-grade packaged apps.
-
-
product
Salt Spray Test Chambers
Labodam salt spray test chambers are reliable instruments for testing the corrosion resistivity of products with painted, organic, or inorganic film surface.
-
product
Dynamic and Fatigue Testing Systems
Instron offers an extensive range of fully-integrated dynamic and fatigue testing systems from 1000 N up to 5000 kN. Incorporating servohydraulic, servo-electric and linear motor technologies, these test instruments cover a broad range of fatigue, dynamic, and static testing applications. These applications include high-cycle fatigue, low-cycle fatigue, thermo-mechanical fatigue, fracture mechanics, crack propagation and growth studies, fracture toughness, bi-axial, axial-torsional, multi-axial, high strain rate, quasi-static, creep, stress-relaxation, and other types of dynamic and static tests.
-
product
Test Automation System for Heavy-Duty Engine Emission Testing
STARS HDEET
STARS HDEET is a Heavy-Duty Engine Emission Test application available as an optional extension to STARS Automation. It provides efficient test cycle execution, emissions equipment control, results calculation and reporting, in compliance with the different legislative standards. Its flexible design offers a wide range of customization while addressing the various requirements for research and development, conformity of production, and certification testing.
-
-
product
Environmental Test Systems
Manufactured products can be exposed to both thermal and mechanical stresses.These should not be considered separately, as the effects may be linked.IMV can supply vibration-test systems combined with climatic chambers to provide complete vibration, temperature and humidity environmental testing.These systems can be custom-designed to meet your application.
-
product
Motor Octane Testing
DewTrak II MO
DewTrakII MO dew point/humidity transmitter is an optical chill mirror hygrometer designed to continuously measure the moisture content and Barometric pressure in the motor octane testing process. It is used to monitor and ensure compliance with test
-
product
Test & Measurement Products
We offer a broad range of test and measurement devices for your scientific, educational, industrial, and process applications. We carry the test and measurements tools you need to analyze, validate, and verify measurements in your electronic and mechanical systems, ensuring compliance to quality assurance and quality control programs. Our selection features portable and bench oscilloscopes, multimeters (DMMs), clamp meters, megohmmeters, stroboscopes and tachometers, power transformers, along with precision meters for humidity, moisture, light, airflow, weather, and vibration.
-
product
Altitude Test Chamber
Aircraft and its components are subject to extreme pressure and climatic conditions during flights. These parameters have a significant influence on the functioning of individual components, and they must be monitored and measured for safety reasons. CME Altitude chamber allow for the testing of aerospace components in an environment with controlled pressure, temperature and humidity parameters. An altitude of 100,000 feet [10 mbar] can be simulated in the test space.
-
product
Meter Test Switches
TESCO introduced the original Meter Test Switch in the early 1920’s. Today, TESCO’s line of Test Switches has been redesigned with the intention to combine the best features of tried and proven switching methods with improvements in materials and construction. All of the current carrying parts are bright tin plated to prevent corrosion. Good operating contact is assured on periodic meter tests, even when the switch has been idle for long periods of time in an unfavorable atmosphere.
-
product
Fluid Contamination Test
Fluid contamination testing determines the abilities of materials to withstand the contaminating fluids, to which they are exposed in service.
-
product
Performance Testing
If you want to check the strength of your application or the server’s strength you will need to find out how much load, in terms of the number of users the application can handle. We use the Performance Testing techniques, to check the load an application can handle.
-
product
Altitude Test Chambers
Altitude chamber testing is important for manufacturers of products that might be shipped via air. It is especially important for defense and aerospace applications where pressure and vacuum conditions are even more intense. Our altitude test chambers simulate a variety of environmental conditions including temperature, altitude, humidity, and vibration for the rigorous testing standards of combined environment.
-
product
Test Set
TS® 19
The Fluke Networks TS19 Test Set combines all the essential test set features at an affordable price. This test set was specifically designed for in-house telecom technicians. Its high impedance monitor prevents accidental disruption of service from clipping onto a data line while in monitor mode, thus ensuring the integrity of critical data lines.
-
product
Meter Test Station
WECO 8000
The innovative WECO 8000 Meter Test Station is the first of its kind – a multi-position test board integrating meter qualification and accuracy. This versatile and economic test station is the solution for utilities needing the ability to switch between functional testing and accuracy testing. Separate multi-position test boards are no longer a necessity.
-
product
Avionics Interfaces & Test Instruments
ARINC 664
Avionics Interface Technologies
AIT’s ARINC 664 test instruments can be used in test and simulation applications that are required to transmit and receive data over the ARINC 664 avionics databus. AIT’s instruments use small form-factor pluggable transceivers (SFP) and support copper or fiber optic physical network interfaces.Using an FPGA based architecture, with multiple embedded processors, the ARINC 664 instruments provide onboard support for upper layer protocol processing (A653, UDP, IP) and utilize DMA to provide optimal data throughput. All ARINC 664 protocol operations, including VL traffic shaping, redundancy management, and IP fragmentation and reassembly, are handled onboard.
-
product
Car-to-X Test Bench
Qosmotec Software Solutions GmbH
The QPER-C2X adaptation, that emulates signal strength between radio devices for Car-to-X communication in the lab, can be combined with the test automation software CANoe from Vector Informatik to enable a fully automated lab test under realistic radio conditions. This combination can be regarded as full test bench setups for Car-to-X test laboratories.
-
product
Full Wafer Test System
FOX-1P
Enables High Throughput, Single Touchdown, Full Wafer Production Testing. Capable of simultaneously testing up to 16,000 die in a single wafer touchdown. Resource configurable up to 16,384 " Universal Channels " - each programmable as anI/O, Clock, Pin Parametric Measurement Unit ( PPMU ) or Device Power Supply ( DPS ). Software-enabled per site flexibility to support small and large device pin count test needs. Comprehensive functional and parametric test capabilities Deep functional pattern data and capture memory optimized for BIST/DFT testing. Per channel PMU for per site parametric testing Individual channel over-current protection to protect wafers and probe cards. Configured for high volume production. Compatible with industry standard probers and probe cards. Available as an integrated test cell with prober, probe cards and 16,384 channel probe I/F. Configurable as a single or dual system integrated test cell.
-
product
Semiconductor Testing Equipment
We provide you with various inspection equipment mainly for the semiconductor post-production process. Also, "inspection boards", "measurement control" and "test applications" are available for you to meet your various needs.
-
product
PMS Leak Test System
The system (Pressure Measuring System) is a portable, complete system for leak tests. This consist of the pressure test kit PMS3000 for performing leak tests with an integrated graphic-capable 4.3” color touch display and a pressure relief kit DAK2000 for discharge test according to W400-2, Part 16 pressure loss methods as well as DIN EN 805. The system is complemented by a variety of connection accessories like the rugged accessory case (individually equipped), the test standpipe PSR and accessories for building gas connection as well as the electronically controlled test pumps EPP and the compact air compressor KLK1030.
-
product
Testing Services
Howland & Lawrence Chamber Services
RF shield testing: IEEE-299, MIL-STD-285, NSA 65-6CTIA CATL certification testing: Probe symmetry and amplitude ripple measurements following Test Plan for Wireless Device Over-the-Air PerformanceAnechoic material test, inspection, remediation: VSWR, inverse spherical nearfield testing of installed material and NRL arch screening tests of individual absorber pieces We can also provide in-process testing of welded steel shielded enclosures with a test technique based on ASME BPVC vacuum box testing—confirm quality of RF welds before the shield envelope is complete. We developed this method for testing the Navy’s Advanced System Integration Lab (ASIL) chamber at Patuxent River, shaving weeks off the construction/testing schedule.
-
product
5G Testing
Teradyne test solutions are at the forefront of the 5G test era. Why? We work with the leading semiconductor manufacturers and provide optimized test coverage for the major wireless standards. From emerging millimeter wave devices to the traditional sub-6GHz, our test solutions are already leading the way.
-
product
Test Automation Management
In many organizations, testing is split: Automation testing is still disconnected from manual testing, and results are reported separately. This makes holistic decision-making, based on the overall testing, close to impossible. Running and managing both your manual and automated tests in PractiTest ensures the coverage of your entire process and gives you a holistic view of your entire QA operation. PractiTest is a centralized solution that helps you make data-driven decisions, focus your team’s efforts and improve your process.
-
product
Thermal Test Boards
Thermal Engineering Associates, Inc.
TEA offers a series of thermal test boards for package characterization and design comparison that conform to to the JEDEC JESD51 standards. The board family, referred to as the TTB-1000 series, consists of two different standard sizes designed to cover a wide range of package sizes. These boards, also referred to as test coupons, provide a well defined mounting environment, will withstand temperatures to 125 oC, and have lead lands terminated in eyelets to allow for hand-wired connection to the board edge contacts. The board mates with a dual 18-pin, 3.962 mm (0.156") pitch edge-card connector.
-
-
product
Test Fixtures
Pneumatically actuated Kelvin connection to custom manufactured device inserts either to complement ART's wide range of precision parametric test equipment or for use with third party measurement hardware.
-
product
Contact Resistance Test Sets
When a high current passes through a pair of mechanically independent metallic contacts, the resistance must be as low as possible. An increase in resistance can lead to additional degradation, as I2R losses will cause local heating of the contact surfaces. Our range of micro-ohmmeters measure both steady state and dynamic low resistance values. With test currents up to 600A available, logging and trending are also available on some models. We ensure that our Contact Resistance tests sets are portable, making them suitable for field measurements. Our contact resistance testers’ portability makes them ideal for a vast range of resistance testing across the entire LV, MV HV and EHV spectrum.
